Current behavior has an EVPN_ENABLED check for both standard and 'no'
forms of 'advertise-svi-ip' and 'advertise-default-gw'. This prevents a
user from removing either command from running config if
'advertise-all-vni' is not present.
This commit removes/adjusts the EVPN_ENABLED checks to always allow the
'no' command so config doesn't get stuck.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
This was mistakenly using the host platform's pointer size rather than
the ELF file's. Only noticeable when cross compiling...
Signed-off-by: David Lamparter <equinox@diac24.net>
We should delete the access-list when the last entry and remark is
deleted. This is already done for prefix-lists.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
We delete the prefix-list when its last entry is deleted, but the check
is missed when we delete the description.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
CLI must never use operational data, because this won't work in
transactional mode. Rework search for prefix-list/access-list entries
using only candidate config.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Allow over-write of message-digest-key interface config. Most
attributes handle multi-instance by ... ignoring instances,
and tolerating repeated config: do the same for md5 auth.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
For some reason the usage of tabs in a string snuck in as well
as using a sockunion2str instead of %pSU. Fix.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When you set OSPF hello-interval for an interface and dead-interval is
not set for this interface, dead-interval will be calculated and set
automatically. "show running-config" will contain an invalid command:
test(config)# interface vpp1
test(config-if)# ip ospf area 0
test(config-if)# ip ospf hello-interval 1
test(config-if)# exit
test(config)#
test(config)# do show running-config
...
interface if1
ip ospf area 0
ip ospf dead-interval minimal hello-multiplier 0
ip ospf hello-interval 1
!
...
It causes frr-reload.py to fail because of this:
# vtysh -c "show running-config no-header" | vtysh -m -f -
line 9: % Unknown command: ip ospf dead-interval minimal hello-multiplier 0
...
With this change, output "ip ospf dead-interval" only if it has value
configured explicitly.
Signed-off-by: Alexander Chernavin <achernavin@netgate.com>
When ip nhrp map multicast is being used, this is usually accompanied by an
iptables rule to block the original multicast packet. This causes sendmsg to
return EPERM.
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
Forwarding multicast is a pre-requisite for allowing multicast based routing
protocols such as OSPF to work with DMVPN
This code relies on externally adding iptables rule. For example:
iptables -A OUTPUT -d 224.0.0.0/24 -o gre1 -j NFLOG --nflog-group 224
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
When certain events occur (connected route changes e.g.)
zebra examines LSPs to see if they might have been affected. For
LSPs with backup nhlfes, skip this immediate processing and
wait for the owning protocol daemon to react.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
