Traceback (most recent call last):
File "/home/docs/checkouts/readthedocs.org/user_builds/frrouting/envs/latest/lib/python3.11/site-packages/sphinx/config.py", line 529, in eval_config_file
exec(code, namespace) # NoQA: S102
^^^^^^^^^^^^^^^^^^^^^
File "/home/docs/checkouts/readthedocs.org/user_builds/frrouting/checkouts/latest/doc/user/conf.py", line 77, in <module>
html_context["READTHEDOCS"] = True
^^^^^^^^^^^^
NameError: name 'html_context' is not defined
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Add a specific debug command to handle srv6 troubleshooting.
Move the srv6 traces that initially were under 'debug zebra packet'
debug.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
For consistency between RIB and BGP, the aigp comparison should
be made after the local route check in bgp bestpath selection.
Signed-off-by: Enke Chen <enchen@paloaltonetworks.com>
The value of 0 is accepted from peers, and can also be set by the
route-map "set aigp-metric igp-metric". For coonsistency, it should
be allowed in "set aigp-metric <value>" as well.
Signed-off-by: Enke Chen <enchen@paloaltonetworks.com>
This command did not allow the operator to display neighbor information
related to graceful-restart when used inside of a vrf.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The minimum and maximum values for BFD timers and multiplier settings
have been updated to align with RFC 5880 requirements.
Since the values inputted via VTY are in milliseconds, the maximum
permissible value on the VTY interface is 4,294,967 milliseconds.
For the multiplier setting, the minimum value is now restricted to be
greater than zero, as zero is not allowed.
The minimum transmit interval has been set to 10 milliseconds to ensure
reliable service performance.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
It was using `-v` which is actually a _version_.
Fixes: 0435b31bb8 ("bgpd: Allow bgp to specify if it will allow v6 routing with v4 nexthops")
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Introduce a command to stop bgpd from enabling IPv6 router advertisement
messages sending on interfaces.
Signed-off-by: Mikhail Sokolovskiy <sokolmish@gmail.com>
With lots of update-groups, subgroups, this could be very tricky and the timer
is spawned even if it's totally unnecessary (default-originate is not enabled).
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Read The Docs made some changes that require us to add some
configuration in our build config files.
Signed-off-by: Quentin Young <qlyoung@qlyoung.net>
When using a regex (or anything that uses `\?` escapes) in python, raw
strings (`r"content"`) should be used so python doesn't consume the
escapes itself. Otherwise we get either broken behavior and/or
`SyntaxWarning: invalid escape sequence '\['`
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Document 'router pim[6] [vrf NAME]' configuration.
All the commands are basically the same, just dropped the
'ip pim[6]' prefix and document them under the router pim block.
Signed-off-by: Nathan Bahr <nbahr@atcorp.com>
In some cases (large scale) it's desired to avoid changing configurations, but
let the BGP to automatically handle ASN changes.
`auto` means the peering can be iBGP or eBGP. It will be automatically detected
and adjusted from the OPEN message.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Add a new start option "-K" to libfrr to denote a graceful start,
and use it in zebra and bgpd.
zebra will use this option to denote a planned FRR graceful restart
(supporting only bgpd currently) to wait for a route sync completion
from bgpd before cleaning up old stale routes from the FIB. An optional
timer provides an upper-bounds for this cleanup.
bgpd will use this option to denote either a planned FRR graceful
restart or a bgpd-only graceful restart, and this will drive the BGP
GR restarting router procedures.
Signed-off-by: Vivek Venkatraman <vivek@nvidia.com>
