The bgp_duplicate_nexthop test installs routes with nexthop's
flags set to both DUPLICATE and FIB: this should not happen.
The DUPLICATE flag of a nexthop indicates this nexthop is already
used in the same nexthop-group, and there is no need to install it
twice in the system; having the FIB flag set indicates that the
nexthop is installed in the system. This is why both flags should
not be set on the same nexthop.
This case happens at installation time, but can also happen
at update time.
- Fix this by not setting the FIB flag value when the DUPLICATE
flag is present.
- Modify the bgp_duplicate_test to check that the FIB flag is not
present on duplicated nexthops.
- Modify the bgp_peer_type_multipath_relax test.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
During the bgp_peer_type_multipath_relax_test, the test does not
check the 'duplicate' flag value of the duplicate nexthop.
Fix this by adding the duplicate value in the expected json files.
Fixes: ee88563ac2 ("bgpd: Add 'bgp bestpath peer-type multipath-relax'")
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
1. The lsp_update_data() function will check for the presence of the ISIS_TLV_DYNAMIC_HOSTNAME in the LSP, and then call isis_dynhn_insert() to add a hostname entry corresponding to the LSP ID. However, when the ISIS_TLV_DYNAMIC_HOSTNAME is not present in the LSP, the hostname entry corresponding to the LSP ID should also be deleted.
2. The command “show isis neighbor” invokes isis_adj_name() to display the System ID or hostname, but it does not check the area->dynhostname flag.
3. When the LSP expires and is removed, the corresponding hostname entry should also be deleted.
4. The TLV for LSP fragmentation will not contain the hostname and should be skipped.
Signed-off-by: zhou-run <zhou.run@h3c.com>
Since the displayed header of "show ip rip" and "show ipv6 ripng" are changed,
we should update tests of ripd and ripngd.
Signed-off-by: anlan_cs <vic.lan@pica8.com>
In some cases (large scale) it's desired to avoid changing configurations, but
let the BGP to automatically handle ASN changes.
`auto` means the peering can be iBGP or eBGP. It will be automatically detected
and adjusted from the OPEN message.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Current code when a link is set down is to just mark the
nexthop group as not properly setup. Leaving situations
where when an interface goes down and show output is
entered we see incorrect state. This is true for anything
that would be checking those flags at that point in time.
Modify the interface down nexthop group code to notice the
nexthops appropriately ( and I mean set the appropriate flags )
and to allow a `show ip route` command to actually display
what is going on with the nexthops.
eva# show ip route 1.0.0.0
Routing entry for 1.0.0.0/32
Known via "sharp", distance 150, metric 0, best
Last update 00:00:06 ago
* 192.168.44.33, via dummy1, weight 1
* 192.168.45.33, via dummy2, weight 1
sharpd@eva:~/frr1$ sudo ip link set dummy2 down
eva# show ip route 1.0.0.0
Routing entry for 1.0.0.0/32
Known via "sharp", distance 150, metric 0, best
Last update 00:00:12 ago
* 192.168.44.33, via dummy1, weight 1
192.168.45.33, via dummy2 inactive, weight 1
Notice now that the 1.0.0.0/32 route now correctly
displays the route for the nexthop group entry.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add a new start option "-K" to libfrr to denote a graceful start,
and use it in zebra and bgpd.
zebra will use this option to denote a planned FRR graceful restart
(supporting only bgpd currently) to wait for a route sync completion
from bgpd before cleaning up old stale routes from the FIB. An optional
timer provides an upper-bounds for this cleanup.
bgpd will use this option to denote either a planned FRR graceful
restart or a bgpd-only graceful restart, and this will drive the BGP
GR restarting router procedures.
Signed-off-by: Vivek Venkatraman <vivek@nvidia.com>
The current OSPF neighbor retransmission operates on a single per-neighbor
periodic timer that sends all LSAs on the list when it expires.
Additionally, since it skips the first retransmission of received LSAs so
that at least the retransmission interval (resulting in a delay of between
the retransmission interval and twice the interval. In environments where
the links are lossy on P2MP networks with "delay-reflood" configured (which
relies on neighbor retransmission in partial meshs), the implementation
is sub-optimal (to say the least).
This commit reimplements OSPF neighbor retransmission as follows:
1. A new data structure making use the application managed
typesafe.h doubly linked list implements an OSPF LSA
list where each node includes a timestamp.
2. The existing neighbor LS retransmission LSDB data structure
is augmented with a pointer to the list node on the LSA
list to faciliate O(1) removal when the LSA is acknowledged.
3. The neighbor LS retransmission timer is set to the expiration
timer of the LSA at the top of the list.
4. When the timer expires, LSAs are retransmitted that within
the window of the current time and a small delta (50 milli-secs
default). The LSAs that are retransmited are given an updated
retransmission time and moved to the end of the LSA list.
5. Configuration is added to set the "retransmission-window" to a
value other than 50 milliseconds.
6. Neighbor and interface LSA retransmission counters are added
to provide insight into the lossiness of the links. However,
these will increment quickly on non-fully meshed P2MP networks
with "delay-reflood" configured.
7. Added a topotest to exercise the implementation on a non-fully
meshed P2MP network with "delay-reflood" configured. The
alternative was to use existing mechanisms to instroduce loss
but these seem less determistic in a topotest.
Signed-off-by: Acee Lindem <acee@lindem.com>
The atomlist test consists of a sequence of (MT) sub-tests, from which
counters are collected and verified. TSAN doesn't know that these
counters are synchronized by way of the sub-test starting and finishing,
so it complains. Just use atomics to get rid of the warning.
(This is solely an issue with the test, not the atomlist code. There
are no warnings from that.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
TSAN warns about leaving the second thread dangling. Doesn't really
matter, but just add a pthread_join to get rid of the warning.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
seqlock_bump() used to return the value before bumping, but that's
unhelpful if you were to actually need it. I had changed it to return
the value after, but the update to the test got lost at some point.
The return value is not in fact used anywhere in FRR, so while it is
a bug, it has zero impact.
NB: yes, test_seqlock is not run, which sounds wrong. The problem here
is that (a) the test itself uses sleeps and is timing sensitive, which
would raise false positives. And (b), the test is meaningless if
executed once. It needs to be run millions of times under various
conditions (e.g. load) to catch rare races, and it needs to be run on
machines with "odd" memory models (in this case I used BE ppc32 and
ppc64 systems as test platforms.)
Fixes: 6046b690b5 ("lib/seqlock: avoid syscalls in no-waiter cases")
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The command "show isis topology" calls print_sys_hostname() to display the system ID or hostname, but it does not check the area->dynhostname flag.
Signed-off-by: zhou-run <zhou.run@h3c.com>
Add a topotest that ensures that when addpath is enabled and two
paths with same nexthop are received, they are sent to ZEBRA which
detects 'duplicate nexthop'.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Some tests may want to use the json facility of iproute2 to
dump some results.
Add an internal API in lib/topotest.py that tells whether iproute2
is json capable or not.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Taking over this development from https://github.com/FRRouting/frr/pull/14788
This commit addresses 4 issues found in the previous PR
1) FRR would accept messages from a spoke without authentication when FRR NHRP had auth configured.
2) The error indication was not being sent in network byte order
3) The debug print in nhrp_connection_authorized was not correctly printing the received password
4) The addresses portion of the mandatory part of the error indication was invalid on the wire (confirmed in wireshark)
Signed-off-by: Dave LeRoy <dleroy@labn.net>
Co-authored-by: Volodymyr Huti <volodymyr.huti@gmail.com>
The isis_tilfa_topo1 topotest is comprehensive and contains a large
amount of reference data. One problem is that, when changes occur,
updating this reference data can be difficult.
To address this problem, this commit introduces a method to
automatically regenerate the reference data by setting the `REGEN_DATA`
environment variable.
Usage:
$ REGEN_DATA=true python3 ./test_isis_tilfa_topo1.py
When `REGEN_DATA` is set, the topotest regenerates reference data
from the current run instead of comparing against existing reference
data. Note that regenerated data must be manually verified for
correctness.
This commit also simplifies the reference data by replacing all diff
files with complete JSON snapshots.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
In this topotest, steps 10-15 were added to test the IS-IS switchover
functionality. In short, two cases were tested: switchover after a
link down event and switchover after a BFD down event. Both cases
were tested in sequence on the same router, rt6. This involved the
following steps:
- Setting the SPF delay timer to 15 seconds
- Shutting down the eth-rt5 interface from the switch side
- Testing the post-switchover RIB and LIB (triggered by the link down
event)
- Testing the post-SPF RIB and LIB
- Bringing the eth-rt5 interface back up
- Configuring a BFD session between rt6 and rt5
- Shutting down the eth-rt5 interface from the switch side once again
- Testing the post-switchover RIB and LIB (triggered by the BFD down
event)
- Testing the post-SPF RIB and LIB
Since the time window to test the post-switchover RIB and LIB was too
narrow (10 seconds), these tests were having sporadic failures.
To resolve this problem, we can simplify the switchover test as follows:
- Setting the SPF delay timer to 60 seconds (not 15)
- Disabling "link-detect" on rt6's eth-rt5 interface
- Shutting down the eth-rt5 interface from the switch side
- On rt6, testing the post-switchover RIB and LIB (triggered by the
BFD down event)
- On rt5, testing the post-switchover RIB and LIB (triggered by the
link down event)
Notice how we can test both post-link-down and post-BFD-down switchover
cases simultaneously by having different "link-detect" configurations
on rt5 and rt6. Additionally, by using a larger SPF delay timer, the
time window to test the post-switchover RIB and LIB is much larger
and less prone to sporadic failures.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
There are 3 tests with OSPF, IS-IS, BGP and MPLS configured:
1. Check the status of BGP session
between North and South == Established
2. Check the connectivity with "ping South -I North"
3. Check the label on the West.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Dmytro Shytyi <dmytro.shytyi@6wind.com>
Check that "show ip route vrf XXX json" and the JSON at key "XXX" of
"show ip route vrf all json" gives the same output.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
- `darr_free_free` to `darr_free` each element prior to `darr_free`
the array.
- `darr_free_func` to call `func` on each element prior to `darr_free`
the array.
Signed-off-by: Christian Hopps <chopps@labn.net>
Topotest relevant changes:
- add support for `timeout` arg to `cmd_*()`
- handle invalid regexp in CLI commands
- fix long interface name support
Full munet changelog:
munet: 0.14.9: add support for `timeout` arg to `cmd_*()`
munet: 0.14.8: cleanup the cleanup (kill) on launch options
munet: 0.14.7: allow multiple extra commands for shell console init
munet: 0.14.6:
- qemu: gather gcda files where munet can find them
- handle invalid regexp in CLI commands
munet: 0.14.5:
- (podman) pull missing images for containers
- fix long interface name support
- add another router example
munet: 0.14.4: mutest: add color to PASS/FAIL indicators on tty consoles
munet: 0.14.3: Add hostnet node that runs it's commands in the host network namespace.
munet: 0.14.2:
- always fail mutest tests on bad json inputs
- improve ssh-remote for common use-case of connecting to host connected devices
- fix ready-cmd for python v3.11+
munet: 0.14.1: Improved host interface support.
Signed-off-by: Christian Hopps <chopps@labn.net>
The test is done on r2. A BGP update is received on r2, and is
filtered on r2. The RIB of r2 does not have the BGP update stored,
but the ADJ-RIB-IN is yet present. To demonstrate this, if the
inbound route-map is removed, then the BGP update should be copied
from the the ADJ-RIB-IN and added to the RIB with the label
value.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
This test ensures that when r1 changes the label value, then
the new value is automatically propagated to remote peer.
This demonstrates that the ADJ-RIB-OUT to r2 has been correctly
updated.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Only output requested information to stdout so it can be
filtered and captured in shell variables etc...
Signed-off-by: Christian Hopps <chopps@labn.net>
Contains 2 testcases. The first does a basic configuration/connectivity.
The second testcase initiates a shortcut through the primary NHS,
verifies shortcut routes are installed. Primary NHS interface brought
down and verify that the shortcut is not impacted. Finally verify that
after the shortcut expires, it is able to be re-established via a backup
NHS.
Signed-off-by: dleroy <dleroy@labn.net>
Locally this test would occassionally fail for me
because the connected route the sharp route being
installed has not fully come up yet due to heavy
load and start up slowness. Add a bit of code
to look for the problem and make sure it doesn't
happen.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The IPv4 directly connected route prefix exists in both the root LSP and the root's neighbor LSP:
1. When generating vertices for directly connected route prefixes with a metric of 0 based on the root LSP, the isis_spf_preload_tent_ip_reach_cb function only generates vertices of type VTYPE_IPREACH_INTERNAL without distinguishing between area->oldmetric and area->newmetric.
2. When generating vertices for the directly connected route prefix based on the neighbor LSP, the isis_spf_process_lsp function will generate vertices of type VTYPE_IPREACH_INTERNAL and VTYPE_IPREACH_TE based on area->oldmetric and area->newmetric, where the vertex metric is the sum of the metric from the root IS to the neighbor IS and from the neighbor IS to the root IS, respectively.
If area->newmetric=1, the same directly connected route prefix will have both VTYPE_IPREACH_INTERNAL vertices with a metric of 0 and VTYPE_IPREACH_TE vertices with a non-zero metric. During route generation, the isis_spf_loop function will prioritize selecting VTYPE_IPREACH_TE vertices, leading to incorrect metrics for the directly connected routes.
Signed-off-by: zhou-run <166502045+zhou-run@users.noreply.github.com>
fix frrbot styling issues found.
1）fix frrbot styling issues found.
2）Roll back the modifications to TE.
Signed-off-by: zhou-run <166502045+zhou-run@users.noreply.github.com>
Maintain code factorization and avoid duplicating code.
Maintain code factorization and avoid duplicating code.
Signed-off-by: zhou-run <166502045+zhou-run@users.noreply.github.com>
isisd: fix frrbot styling issues found
fix frrbot styling issues found
Signed-off-by: zhou-run <166502045+zhou-run@users.noreply.github.com>
isisd: fix frrbot styling issues found
fix frrbot styling issues found
Signed-off-by: zhou-run <166502045+zhou-run@users.noreply.github.com>
isisd: Resolve compilation issues.
Resolve compilation issues.
Signed-off-by: zhou-run <166502045+zhou-run@users.noreply.github.com>
isisd: Resolve compilation issues.
Resolve compilation issues.
Signed-off-by: zhou-run <166502045+zhou-run@users.noreply.github.com>
isisd: fix frrbot styling issues found
fix frrbot styling issues found
Signed-off-by: zhou-run <166502045+zhou-run@users.noreply.github.com>
isisd: fix frrbot styling issues found
fix frrbot styling issues found
Signed-off-by: zhou-run <166502045+zhou-run@users.noreply.github.com>
isisd: Resolve compilation issues.
Resolve compilation issues.
Signed-off-by: zhou-run <166502045+zhou-run@users.noreply.github.com>
"show isis database [detail] json" returns invalid or incorrect JSON
that is difficult to parse.
Fix key with '-' characters, add booleans and null data when possible.
Deprecate the old format.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Current command (bundled two into one) is absolutely wrong.
When you configure TCP session with the source, the command thinks, that
it's a SSH session with a username.
It's much better to split this into two separate commands where it's much
easier to do the changes in the future (if more options comes in).
Yes, this is a breaking change, but there is no other proper way to overcome
this.
Bonus note how it looks, which also can lead to crashes (due to port 0x0):
```
(gdb) p *cache->tr_config.ssh_config
$11 = {host = 0x5555562f9cd0 "1.1.1.1", port = 0, bindaddr = 0x0,
username = 0x55555629ad00 "",
server_hostkey_path = 0x7ffff53667a0 <rpki_create_socket> "Uf\017\357\300H\211\345AWAVAUATSH\201", <incomplete sequence \354\230>, client_privkey_path = 0x0,
data = 0x0, new_socket = 0x51, connect_timeout = 4143762592,
password = 0x7ffff6fccca0 <main_arena+96> "\300\"0VUU"}
(gdb) p *cache->tr_config.tcp_config
$12 = {host = 0x5555562f9cd0 "1.1.1.1", port = 0x0, bindaddr = 0x0,
data = 0x55555629ad00, new_socket = 0x7ffff53667a0 <rpki_create_socket>,
connect_timeout = 0}
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Leaked route from the l3VRF are installed with the loopback as the
nexthop interface instead of the real interface.
> B>* 10.0.0.0/30 [20/0] is directly connected, lo (vrf default), weight 1, 00:21:01
Routing of packet from a L3VRF to the default L3VRF destined to a leak
prefix fails because of the default routing rules on Linux.
> 0: from all lookup local
> 1000: from all lookup [l3mdev-table]
> 32766: from all lookup main
> 32767: from all lookup default
When the packet is received in the loopback interface, the local rules
are checked without match, then the l3mdev-table says to route to the
loopback. A routing loop occurs (TTL is decreasing).
> 12:26:27.928748 ens37 In IP (tos 0x0, ttl 64, id 26402, offset 0, flags [DF], proto ICMP (1), length 84)
> 10.0.0.2 > 10.0.1.2: ICMP echo request, id 47463, seq 1, length 64
> 12:26:27.928784 red Out IP (tos 0x0, ttl 63, id 26402, offset 0, flags [DF], proto ICMP (1), length 84)
> 10.0.0.2 > 10.0.1.2: ICMP echo request, id 47463, seq 1, length 64
> 12:26:27.928797 ens38 Out IP (tos 0x0, ttl 63, id 26402, offset 0, flags [DF], proto ICMP (1), length 84)
> 10.0.0.2 > 10.0.1.2: ICMP echo request, id 47463, seq 1, length 64
Do not set the lo interface as a nexthop interface. Keep the real
interface where possible.
Fixes: db7cf73a33 ("bgpd: fix interface on leaks from redistribute connected")
Fixes: 067fbab4e4 ("bgpd: fix interface on leaks from network statement")
Fixes: 8a02d9fe1e ("bgpd: Set nh ifindex to VRF's interface, not the real")
Fixes: https://github.com/FRRouting/frr/issues/15909
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
`make check` should run w/o installing FRR first. Thus we need to embed
the yang modules otherwise mgmtd unit-test fails.
Signed-off-by: Christian Hopps <chopps@labn.net>
add some match in route map rules
add some set unset bgp access path list
add another prefix for better tests discrimination
update expected results
Signed-off-by: Francois Dumontet <francois.dumontet@6wind.com>
- Add separate get, get-config, get-state operations to query command, as
well as switching default output to JSON.
- Add an `--xml` to change the output format.
- move printss to logging.debug so output is a machine parseable result.
Signed-off-by: Christian Hopps <chopps@labn.net>
Similarly to recently fixed 'show ip[v6] prefix-list ...' - PR#15750,
json output is not valid for 'show ip[v6] access-list ... json' commands,
as it goes through all the running daemons and for each one it calls
'filter_show' creating a new json object. To aggreagate the output
and create a valid json that can later be parsed, the commands were
moved to vtysh and formatted accordingly
Signed-off-by: Piotr Suchy <piotrsuchy@proton.me>
So far, this test only convered redundant paths to one ABR, now it checks
redundant paths to redundant ABRs, covering both cases. Useful as a
regression test for #15777.
Signed-off-by: Martin Buck <mb-tmp-tvguho.pbz@gromit.dyndns.org>
It's just annoying when the linter tells to apply the formatting for the code
you didn't touch.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
When testing SNMP service on FRR, the following error message may
appear on some distros.
> # snmpwalk -v2c -c public .1.3.6 1.1.1.1 <OID>
> Bad operator (INTEGER): At line 73 in /usr/share/snmp/mibs/ietf/SNMPv2-PDU
> [..then result ..]
>
The error message is due to the /etc/snmp/snmp.conf file. By default, this
file is used by both snmp server and client side. The net-snmp MIB parsing
routing loads MIBS, to bind oids with the naming scheme used by the MIBS.
> # cat /etc/frr/snmp.conf
> [snmp]
> mibs +ALL
>
A potential fix would consist in modifying the SNMPv2-PDU.mib file: the
problem is known on ubuntu distros, as the snmp-mibs-downloader package
has not updated the SNMPv2-PDU.mib file.
The choice is done to not modify the original distro where the test is run
on. Fix the topotests by ignoring the 'SNMPv2-PDU line 73" error message, and
keep the other error messages that may happen, for instance, when an
unknown oid name value is requested.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Before the patch-set, ce1 was sending an IPv6 Link-local as global and
link-local nexthop to pe1.
Set bgp_vrf_leaking_5549_routes in accordance with the previous fixes.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add bgp_nexthop_mp_ipv4_6 topotest to test to nexhop value with
MP-BGP IPv4 and IPv6 on IPv4 peering. The test has route-reflector,
route-server, iBGP and eBGP peers.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
- by using symlinks in the rundir (/tmp) into the source/build directory
we avoid needing to copy the *.gcda stat files into the source/build dir.
Signed-off-by: Christian Hopps <chopps@labn.net>
When a BFD down notification is received and the C-bit is set in both
directions, any ongoing graceful restart should be aborted and stale
routes removed from the RIB.
This commit updates the `bfd_bgp_cbit_topo3` topotest accordingly to
fix the expected outcomes in the `test_bfd_loss_intermediate` test.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This commit adds the capabiity to filter OSPF neighbors using a
prefix-list with rules matching the neighbor's IP source address.
Configuration, filtering, immediate neighbor pruning, topo-tests,
and documentation are included. The command is:
ip ospf neighbor-filter <prefix-list> [A.B.C.D]
Signed-off-by: Acee Lindem <acee@lindem.com>
The Support bundle generation was/is failing in both
our upstream ci and locally. This cleans up the failures
that I am seeing such that tests now continue to run
instead of aborting the test run.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
In topotest, a given interface has only the ignore routes bit turned
on for IPv6 only, whereas topotest is expected to turn it on for all
address families.
> # show interface
> Interface r2-r3-eth2 is up, line protocol is up
> [..]
> flags: <UP,BROADCAST,RUNNING,MULTICAST>
> Ignore all v6 routes with linkdown
> Type: Ethernet
> [..]
This is because the only the 'default' ipv6 ignore sysctl is set to
1. Set also the /proc/sys/net/conf/<family>/default/ignore_routes_with_linkdown
flag, to have same behaviour for ipv4 and ipv6.
Fixes: 4958158787 ("tests: micronet: update infra")
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This extends non-broadcast support to point-to-multipoint networks.
Neighbors will be explicitly configured and polled in lieu of multicast
dicovery. Toptotests and documentation updates are included.
Additionally, the ospf neighbor commands have been greatly simplified taking
advantage of DEFPY() capabilities.
The AllOSPFRouters (224.0.0.5) is still joined for non-broadcast networks
since it is joined for NBMA networks. It seems this could be removed but
it should done be in a separate commit.
Signed-off-by: Acee Lindem <acee@lindem.com>
This topotest covers the PR-15574's coverage
where a change is not to delete neighbors when
the associated peer-group's remote-as is removed.
Ticket: #3828243
Testing:
test_bgp_peer-group.py::test_bgp_peer_group
---------------------------------------------------------------------------- live log call -----------------------------------------------------------------------------
2024-03-29 18:12:22,608 INFO: r1: checking if daemons are running
2024-03-29 18:12:22,802 INFO: r2: checking if daemons are running
2024-03-29 18:12:22,911 INFO: r3: checking if daemons are running
2024-03-29 18:12:23,015 INFO: topo: Remove bgp peer-group PG1 remote-as neighbor should be retained
2024-03-29 18:12:25,605 INFO: topo: Re-add bgp peer-group PG1 remote-as neighbor should be established
----------------------------------------------------------- generated xml file: /tmp/topotests/topotests.xml -----------------------------------------------------------
========================================================================== 2 passed in 17.63s ==========================================================================
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Add a new flag BGP_PATH_UNSORTED to keep track
of sorted -vs- unsorted path_info's. Add some
ability to the system to understand when that
flag is set.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
lib: don't define a `fallthrough` in c++ to avoid conflict with protobuf c++
check: add link libs required by some versions of grpc++ or it's dependent
linked libs
tests: don't fail the test due to known at exit memleaks
Signed-off-by: Christian Hopps <chopps@labn.net>
Apparently test_bgp_peer_type_multipath_relax.py does
no really need to run a `setup_vrfs` script. Looking
at the other configuration for this test there are
no vrf's in the frr configuration. So let's remove it
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Ensure that the fpm module connects to the specified listener
and then ensure that 10k routes from sharpd are installed
into the system and then are removed.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add the ability to run a fpm listener to the testing
system. This is nothing more just allowing the test
system to bring it up.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
adding a tests about:
"no bgp as-path access-list" command.
the folloxing "clear bgp *" command leads to the
crash exhibited above.
a sleep had been added to capture the crash befor the end of scenario.
50 ../sysdeps/unix/sysv/linux/raise.c: No such file or directory.
[Current thread is 1 (Thread 0x7f5f05cbb9c0 (LWP 1371086))]
(gdb) bt
context=0x7ffcf2c216c0) at lib/sigevent.c:248
acl_list=0x55c976ec03c0) at bgpd/bgp_aspath.c:1688
dummy=0x7ffcf2c22340, object=0x7ffcf2c21e70) at bgpd/bgp_routemap.c:2401
match_object=0x7ffcf2c21e70, set_object=0x7ffcf2c21e70, pref=0x0)
at lib/routemap.c:2687
attr=0x7ffcf2c220b0, afi=AFI_IP, safi=SAFI_UNICAST, rmap_name=0x0, label=0x0,
num_labels=0, dest=0x55c976ebeaf0) at bgpd/bgp_route.c:1807
addpath_id=0, attr=0x7ffcf2c22450, afi=AFI_IP, safi=SAFI_UNICAST, type=10,
sub_type=0, prd=0x0, label=0x0, num_labels=0, soft_reconfig=0, evpn=0x0)
at bgpd/bgp_route.c:4424
packet=0x7ffcf2c22410) at bgpd/bgp_route.c:6266
packet=0x7ffcf2c22410, mp_withdraw=false) at bgpd/bgp_packet.c:341
peer=0x55c976e89ed0, size=43) at bgpd/bgp_packet.c:2414
at bgpd/bgp_packet.c:3899
Signed-off-by: Francois Dumontet <francois.dumontet@6wind.com>
This test uses the connected ipv4 mapped ipv6 prefix
to resolve the received BGP routes.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: François Dumontet <francois.dumontet@6wind.com>
This test is failing locally for me 100% of the time
since zebra was converted to mgmtd usage. The failed
command is:
torm11# show evpn mac vni 1000 mac 00:00:00:00:00:11 json
{
"00:00:00:00:00:11":{
"type":"auto",
"uptime":"00:02:01",
"localSequence":0,
"remoteSequence":0,
"detectionCount":0,
"isDuplicate":false,
"syncNeighCount":0,
"neighbors":{
"active":[
],
"inactive":[
"45.0.0.11"
]
}
}
}
The test is expecting an esi as a key in the output. Re-arranging
the startup of the tor's before the hosts fixes the issue.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Set static router-id for OSPF, because otherwise it depends on timing of
router-id updates received from zebra and may differ between test runs.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Check that local route leaks are set to "inactive" when the VRF
interface is shutdown and, conversely, that they are set to "active"
when the VRF interface is unshut.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Test functions were duplicated by mistakes. They were identical.
Fixes: 8af61c8a34 ("topotests: test leak from the default vrf")
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Following new json decoder for Opaque LSA, this patch adapts the ospfapiclient
test to the new json output.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Current code assumes that notification is always sent in stripped JSON
format and therefore notification xpath starts at the third symbol of
notification data. Assuming JSON is more or less fine, because this
representation is internal to FRR, but the assumption about the xpath is
wrong, because it won't work for not top-level notifications. YANG
allows to define notification as a child for some data node deep into
the tree and in this case notification data contains not only the
notification node itself, but also all its parents.
To fix the issue, parse the notification data and get its xpath from its
schema node.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Remove sleep time in test_bgp_snmp_bgp4v2mib before run_and_expect and
reduce wait intervals for faster test convergence.
Signed-off-by: Martin Winter <mwinter@opensourcerouting.org>
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
Replace OID string parsing of snmptrap log files based on odd/even line
numbers with regex string search to prevent test failures in cases where
log entries don't match assumed order.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
cisco routers are not dealing fairly whith unsupported capabilities.
When a cisco router receive an unsupported capabilities it reset the
negociation without notifying the unmatching capability as described in
RFC2842.
Cisco suggest the use of
neighbor x.x.x.x capability fqdn
to avoid the use of fqdn in open message.
this new command is to remove the use of fqdn capability in the
open message with the peer "x.x.x.x".
Link: https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/116189-problemsolution-technology-00.pdf
Signed-off-by: Francois Dumontet <francois.dumontet@6wind.com>
Currently, staticd configuration is tightly coupled with VRF existence.
Because of that, it has to use a hack in NB infrastructure to create a
VRF configuration when at least one static route is configured for this
VRF. This hack is incompatible with mgmtd, because mgmtd doesn't execute
configuration callbacks. Because of that, the configuration may become
out of sync between mgmtd and staticd. There are two main cases:
1. Create static route in a VRF. The VRF data node will be created
automatically in staticd by the NB hack, but not in mgmtd.
2. Delete VRF which has some static routes configured. The static route
configuration will be deleted from staticd by the NB hack, but not
from mgmtd.
To fix the problem, decouple configuration of static routes from VRF
configuration. Now it is possible to configure static routes even if the
VRF doesn't exist yet. Once the VRF is created, staticd applies all the
preconfigured routes.
This change also fixes the problem with static routes being preserved in
the system when staticd "control-plane-protocol" container is deleted
but the VRF is still configured.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Add tests in bgp_vrf_route_leak_basic topotest to check that route
leaking from the default VRF results in an operational route.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add a test in bgp_vrf_route_leak_basic topotest to check that route
leaking from a non existing VRF results in an inactive route.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Update bgp_vrf_route_leak_basic to set up the VRF interfaces. Otherwise
the routes to the VRF interface are inactives.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Previously, routes leaked from one VRF to another VRF were associated
with the original nexthop interface.
Due to this change, the `bgp_srv6l3vpn_route_leak` topotest always fails
because it still expects the nexthop interface.
This commit fixes the expected interface name in the
`bgp_srv6l3vpn_route_leak` topotest.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Leaked connected routes have now the following nexthop interfaces:
- lo for routes imported from the default VRF
- or the VRF interface for routes imported from the other VRFs.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
We shouldn't pass "lo" as an interface to create_interface_in_kernel.
It always exists, and this function flushes all configured IP addresses
from it.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
This needs to be used for persistent state, which currently is misplaced
into `/var/run` / `/run` where it gets deleted across reboots.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
A large set of routers are connected to the same switch. Each router
shares a single network. All shared networks must be reachable from all
routers.
Signed-off-by: "Adriano Marto Reis" <adrianomarto@gmail.com>
The name of the `test_zebra_seg6local_routes` test is wrong. The goal
of this test is to verify seg6 routes (not seg6local routes).
Let's put the correct name.
Signed-off-by: Carmine Scarpitta <cscarpit@cisco.com>
Per the RFC6860, check OSPFv2 using point-to-multipoint
over Ethernet.
Enable the behavior of the RFC6860 using:
ip ospf prefix-suppress A.B.C.D
See:
https://www.rfc-editor.org/rfc/rfc6860#section-2.3.2.2
Note that nexthops are not required to assess the checks.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
Getting this error:
2024-01-17 19:05:20,688 WARNING: torm11: Router(torm11): proc failed: rc 255 pid 2436134
args: /usr/bin/nsenter --mount=/proc/2435168/ns/mnt --net=/proc/2435168/ns/net --uts=/proc/2435168/ns/uts -F /bin/bash -c /sbin/bridge vlan add vid 1000 dev bridge
stdout: RTNETLINK answers: Operation not supported
stderr: *empty*
As I understand it the correct thing to do here is pass in:
bridge vlan add vid 1000 dev bridge self
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
