This is to avoid breaking changes between existing deployments of
extended community for bandwidth encoding. By default FRR uses uint32
to encode bandwidth, which is not as the draft requires (IEEE floating-point).
This switch enables the required encoding per-peer.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
```
exit1-debian-9# show ip bgp large-community-list
(1-500) large-community-list number
LCOMMUNITY_LIST_NAME large-community-list name
large-testas
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
```
exit1-debian-9# show ip bgp community-list ?
(1-500) community-list number
COMMUNITY_LIST_NAME community-list name
testas
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
When bgp receives the admin distance from a redistribution statement
let's store that distance for later usage.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When an EVPN prefix flaps too quickly such that the new advertisement
is received prior to the full processing of the prior withdraw, we may
get into a state where the route doesn't get imported properly into
MAC or IP VRFs. Ensure that we do the route import in such cases.
Suggested-by: Sri Mohana Singamsetty <msingamsetty@vmware.com>
Suggested-by: Ameya Dharkar <adharkar@vmware.com>
Signed-off-by: Vivek Venkatraman <vivek@nvidia.com>
Add a bit of code to allow for auto-completion of the community
alias command when attempting to use it for show commands.
example:
eva(config)# bgp community alias 11:22 FOO
eva(config)# end
eva# show bgp ipv4 uni alias
ALIAS_NAME BGP community alias
FOO
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Some BGP updates received by BGP invite local router to
install a route through itself. The system will not do it, and
the route should be considered as not valid at the earliest.
This case is detected on the zebra, and this detection prevents
from trying to install this route to the local system. However,
the nexthop tracking mechanism is called, and acts as if the route
was valid, which is not the case.
By detecting in BGP that use case, we avoid installing the invalid
routes.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Force the processing of existing network configurations when VRF is
created, otherwise will be skipped in bgp_static_update().
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Add a terse option to show bgp summary to shorten output.
Do not show the following information about the BGP
instances: the number of RIB entries, the table version and the used memory.
The "terse" option can be used in combination with the "remote-as", "neighbor",
"failed" and "established" filters, and with the "wide" option as well.
Before patch:
ubuntu# show bgp summary remote-as 123456
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
% No matching neighbor
Total number of neighbors 5
After patch:
ubuntu# show bgp summary remote-as 123456 terse
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 1
% No matching neighbor
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
While installing this route in the EVPN table, make sure all the conditions
mentioned in the draft
https://tools.ietf.org/html/draft-ietf-bess-evpn-prefix-advertisement-11 are
met.
Draft mentions following conditions:
- ESI and gateway IP cannot be both nonzero at the same time.
- ESI, gateway IP, RMAC and VNI label all cannot be 0 at the same time.
If the received EVPN RT-5 route does not meet these conditions, the route is
treated as withdraw.
Signed-off-by: Ameya Dharkar <adharkar@vmware.com>
Gateway IP overlay index is generated for EVPN RT-5 when following CLI is
configured.
router bgp 100 vrf vrf-blue
address-family l2vpn evpn
advertise ipv4 unicast gateway-ip
advertise ipv6 unicast gateway-ip
BGP nexthop of the VRF IP/IPv6 route is set as the gateway IP of the
corresponding EVPN RT-5
Signed-off-by: Ameya Dharkar <adharkar@vmware.com>
We are inconsistently using peer_establiahed(peer) with
sometimes using `peer->status == Established`. Just Convert
over to using the function for consistency.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
BGP configuration changes that imply recomputing the BGP route table
(e.g. modifying route-maps, setting bgp graceful-shutdown) might be a
long time process depending on the size of the BGP table and the
route-map numbers and complexity. For example, setups with full
Internet routes take something like one minute to reprocess all the
prefixes when graceful-shutdown is configured. During this time, a
"show bgp commands" request on vtysh results in blocking the shell until
the soft reconfigure table task is over.
This patch splits bgp_soft_reconfig_table task into thread jobs of 25K
prefixes.
Some tests on a full Internet route setup show that after reconfiguring
route-maps or graceful-shutdown, vtysh is not stucked anymore. We are
now able to request commands like "show bgp summary" after 1 or 2
seconds instead of 30 to 60s.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
For EVPN routes, there is specific logic in place for path selection
surrounding MAC Mobility. For pure type-5 routes, if a route is
advertised with a MED, this is ignored since it ultimately falls inside
of the EVPN specific path selection logic, and ultimately selects the
lower IP address. This change ensures only type-2 routes fall into the
EVPN BGP path selection.
Signed-off-by: Neal Shrader <neal@digitalocean.com>
Show alias name instead of numerical value in `show bgp <prefix>. E.g.:
```
root@exit1-debian-9:~/frr# vtysh -c 'sh run' | grep 'bgp community alias'
bgp community alias 65001:123 community-1
bgp community alias 65001:123:1 lcommunity-1
root@exit1-debian-9:~/frr#
```
```
exit1-debian-9# sh ip bgp 172.16.16.1/32
BGP routing table entry for 172.16.16.1/32, version 21
Paths: (2 available, best #2, table default)
Advertised to non peer-group peers:
65030
192.168.0.2 from home-spine1.donatas.net(192.168.0.2) (172.16.16.1)
Origin incomplete, metric 0, valid, external, best (Neighbor IP)
Community: 65001:12 65001:13 community-1 65001:65534
Large Community: lcommunity-1 65001:123:2
Last update: Fri Apr 16 12:51:27 2021
exit1-debian-9#
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
