During a debugging session last night I discovered that I was
still having some `fun` figuring out why zebra was not making
a route's nexthop active. After some debugging I figured out
that I was missing some states that we could end up in that
didn't have debug information about what happened in nexthop_active.
Add the missing breadcrumbs for nexthop resolution. In addition
add a bit of code to notice the ebgp state without recursion turned
on and to let the user know about it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
libunwind provides an alternate to backtrace() for printing out the call
stack of a particular location. It doesn't use the frame pointer, it
goes by the DWARF debug info. In most cases the traces have exactly the
same information, but there are some situations where libunwind traces
are better.
(On some platforms, the libc backtrace() also uses the DWARF debug info
[e.g.: ARM backtraces are impossible without it] but this is not the
case everywhere, especially not on BSD libexecinfo.)
Signed-off-by: David Lamparter <equinox@diac24.net>
on some cases, kernel routes are not selected, because the kernel
suppressed it without informing the netlink layer that the route has
been suppressed ( for instance, when an interface goes down, the route
never goes back when interface goes up again). This commit intends to
suppress that entry from zebra.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Recent changes to the nht code in bgp caused us to actually
keep a true count of v6 nexthop paths when using v4 over v6.
This change introduced a race condition on shutdown on who
got to the bnc cache first( the v4 table or not ). Effectively
we were allowing the continued existence of the path->nexthop
pointing to the freed bnc. This was especially true when
we had route leaking. So when we free the bnc make sure
we clean up the path->nexthop variables pointing at it too.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If you are using bgp unnumbered( or interface based peers )
when we detect an error give the user a bit more of a clue
what they may have done wrong.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
IS-IS would ignore any area lsp-mtu setting configured after initial
creation of the LSP since move to the new tlv serialized/deserializer.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
isisd would crash when lsp fragments aged out, since they got freed
correctly, but were not removed from LSP0's linked list of fragments.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Add the ability to aggregate routes to handle
extended communities. Make the actions similiar
to what we do for normal communities.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The evpn_vtep_ip_cmp function must return positive and negative
numbers for when we are doing sorted linked list inserts.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The purpose of adding a l2vni as an sorted list is
shot in the foot when the l2vni compare function only
returns 0 or 1. This will cause subtle crashes when
we add sorted and we end up with multiple list node pointing
to the same thing.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Use the proper multi hop hash for matching multi hop peers.
Spotted by Dmitrii Turlupov.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Use ospf6_prefix_same for comparing two exact same prefix
to determine ECMP for a route.
ospf6_route_cmp expects two different prefix rather
being exactly same.
Ticket:CM-22630
Testing Done:
performed ECMP of intra network prefix route via
sending same route via different available
ospf6 paths.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Add the '[no] flood <disable|head-end-replication>' command
to the l2vpn evpn afi/safi sub commands for bgp. This command
when entered as 'flood disable' will turn off type 3 route
generation for the transmittal of the type 3 route necessary
for BUM replication on the remote VTEP. Additionally it will
turn off the BUM handling via the new zebra command,
ZEBRA_VXLAN_FLOOD_CONTROL.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow the modification of whether or not we will allow
BUM flooding on the vxlan bridge. To do this allow
the upper level protocol to specify via the ZEBRA_VXLAN_FLOOD_CONTROL
zapi message.
If flooding is disabled then BUM traffic will not be forwarded
to other VTEP's.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
1. "show bgp ipv4 json"
- Added "network" field which displays a prefix in 'prefix/prefixlen' format.
2. "show bgp ipv6 json"
- Added "network" field which displays a prefix in 'prefix/prefixlen' format.
- JSON does not have "prefix", "prefixLen" fields which are present in IPv4
command. Added these fields as they are useful.
3. "show bgp ipv4/ipv6 neighbor <neighbor_addr> advertised-routes json"
- Added "network" field.
4. "show bgp ipv4/ipv6 summary json"
- Added "pfxSnt" for peers. This count is obtained from corresponding
update_subgroup.
5. "show bgp neighbor json"
- Added "sentPrefixCounter"
Signed-off-by: Ameya Dharkar <adharkar@vmware.org>
Work to handle the route-maps, namely the header changes in zebra_vrf.h
and the mapping of using that everywhere
Signed-off-by: vishaldhingra vdhingra@vmware.com
When reading in config files and we have failures on multiple
lines actually note the actual failure lines and return them.
This fixes an issue where we stopped counting errors after
the first one and we got missleading line numbers that
did not correspond to the actual problem.
This is fixed:
sharpd@donna ~/frr> sudo /usr/lib/frr/pimd --log=stdout -A 127.0.0.1 -f /etc/frr/pimd.conf
2018/10/11 09:41:01 PIM: VRF Created: default(0)
2018/10/11 09:41:01 PIM: pim_vrf_enable: for default
2018/10/11 09:41:01 PIM: zclient_lookup_sched_now: zclient lookup immediate connection scheduled
2018/10/11 09:41:01 PIM: zclient_lookup_new: zclient lookup socket initialized
2018/10/11 09:41:01 PIM: pimd 6.1-dev starting: vty@2611
2018/10/11 09:41:01 PIM: [EC 100663304] ERROR: No such command on config line 2: inteface lo
2018/10/11 09:41:01 PIM: [EC 100663304] ERROR: No such command on config line 3: ip igmp
2018/10/11 09:41:01 PIM: [EC 100663304] ERROR: No such command on config line 4: ip igmp join 224.1.1.1 13.13.13.2
^C2018/10/11 09:45:09 PIM: Terminating on signal SIGINT
2018/10/11 09:45:09 PIM: VRF Deletion: default(0)
Fixes: #3161
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
