Just disable pbr tests on anything less than 4.10.
This has to do with the fact that the arm platform
is not allowing us to install a route into a
non default table using a interface associated
with a vrf.
ip route add default 4.5.6.7 via swp39 table 10000
When swp39 is in a vrf other than default
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
From last addition we can tell that the nexthop-group C is
installed but pbr does not think it is. This failure
has been consistent the last 4-5 runs in master. Lets
add a bit more data gathering to figure out what is going on.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Include vrf name with interface name when topojson framework
generates interface configuration. This matches the output of
'show runn', and makes config reset less disruptive. Also
stop removing configured debugs and log output when re-generating
config.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
This may be expanded in the future as we figure out more things
to gather when the test has gone south.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This is the bulk part extracted from "bgpd: Convert from `struct
bgp_node` to `struct bgp_dest`". It should not result in any functional
change.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Under heavy load some systems may still be processing. Let's give
the system some time to figure out what is going wrong.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Announcements that are marked as invalid were previously not revalidated.
This was fixed by replacing the range lookup with a subtree lookup.
Signed-off-by: Marcel Röthke <marcel.roethke@haw-hamburg.de>
Error Message seen:
2020-06-11 14:00:35,288 ERROR: assert failed at "test_ebgp_ecmp_topo2/test_ecmp_after_clear_bgp[redist_static]": Testcase test_ecmp_after_clear_bgp[redist_static] : Failed
Error: TIMEOUT!! BGP is not converged in 30 seconds for router r3
assert 'TIMEOUT!! BGP is not converged in 30 seconds for router r3' is True
if a retry for a failed connection is 120 seconds we should wait slightly
longer than a retry session, which this clear test was not doing.
Especially since we know our topotests are lossy on data under load.
Apparently I changed this earlier to 90 seconds, but a retry window
is 120. Not sure wtf I was thinking
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add some basic route scale tests to ensure that we can
install a large number of routes. Also grab some timings
so that we can keep track and see if anything substantially
changes over time.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The convergence timeout in lib/bgp.py was something like 40 secs;
that's not really long enough for the CI. Raise the timeout to
40 x 3 secs.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Use `json_cmp` instead of raw text comparison. It should fix some of the
ordering problems we are seeing in CI runs.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Update OSPF Segment Routing topotest in conformity to ECMP
- Add one more interface between r1 and r2 for ECMP
- Anonymize Adjacency SID
- Update expected json output
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
The bgp_as_wide_bgp_identifier test can time out after
30 seconds waiting for convergence. This is of course
a problem in our test setup where we know that convergence
can fail on first startup due to load issues in the
topology. Additionally we also know that our default time
for bgp sessions is 120 seconds to retry. Give things
a bit longer than 120 seconds to actually fail
instead of 30 seconds
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Just add a basic test for pbr. This code
does not actually test installation in the kernel at this
point in time.
What we do do is make sure pbr is in a sane state after
some very basic configuration.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Just a simple setup for pbr to prove it starts. Once the json
code for pbr gets in we can add more.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Issue number #6291 describes how OSPFd crashes after being deleted and then
added again with configuration when segment routing is used.
The problem occurs in ospf_ri.c because the OspfRI structures retains
the reference to the old area pointer which is mofified when ospfd is
reactivated by configuration. When segment routing is activated, the LSA Router
Information is sent with reference to the old area pointer, instead the new one,
which causes the crash. The same problem is also present in ospf_ext.c with
OspfEXT structure and Extended Link/Prefix structure.
This commit introduces Extended Link/Prefix and Router Information LSAs flusing
when OSPFd is stopped when configuration is removed and adds the correct
initialization to the area pointer in OspfRI and Extended Link/Prefix structure
when OSPFd is re-enabled with the configuration. Area pointer has been removed
from the OspfEXT structure as it is never used with this commit.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Changes:
- Renamed file so we don't get confused when it fails.
- Use `json_cmp` instead of direct key access.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
The involved piece of code is supposed to find a 'closest' match for two
JSON structures using another JSON diff. However, it can happen that
during that new diff the JSON structures are altered (elements from a
list are deleted when 'found'). This is in general ok when the deleted
element is part of the JSON structure which 'matches', but when it later
turns out that some other element of the structure doesn't fit, then the
whole structure should be recovered. This is now realized by using a
deepcopy for the besaid new JSON diff such that the original is only
altered (e.g. deleted) when the diff is clean.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
1. Adding 4 testcases to this testsuite to verify BGP multi-vrf functionality
2. Adding supporting JSON file to create topology and base config
3. Execution time is ~3 mins
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
1. Adding 22 testcases to this testsuite to verify BGP multi-vrf functionality
2. Adding supporting JSON file to create topology and base config
3. Execution time is ~7 mins.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
Now that the "frr-interface" list has a "state" container, move the
IS-IS interface state nodes underneath it using a new augmentation.
Also, update the IS-IS SR topotest to account for this change. Make
use of symlinks where possible to avoid having multiple files with
the same content.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
