The 'show zebra' command really shouldn't be owned
by ospf6. This command is a specialized command
to show some basic information about ospf6 and zebra
so limit it to ospf6.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The indentation of ifjoin_to_noinfo was not consistent with
the rest of the function and caused clang to loose it's mind
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The indentation of ifjoin_to_noinfo was not consistent with
the rest of the function and caused clang to loose it's mind
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This reverts commit fa14eb2c0b.
This was for stable/2.0 and wasn't intended to go on stable/3.0
-- my bad, missed this in the merge.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Revert "ospf6d: fix decimal area ID cli"
commit a27cb3cfe9
Revert "bgpd: add back unicast option to 'address-family vpnv(4&6)' Issue #459"
commit 399598bf6b
Revert "Fix the memory leak"
commit d8d58e9839
Revert "zebra: 'no ip route 4.1.1.19 255.255.255.255 99' is ambiguous"
commit 83f3561935
Revert "ospf6d: Allow unconfig of unknown lsa's"
commit 5b0747d71d
Revert "Fix the "Dead assignment" of clang SA."
commit 3a6570a1f1
Revert "snapcraft: Improve README.usage.md based on feedback received"
commit 2a3a819a9c
Revert "zebra: stop deregistering static nexthops unless removing the static"
commit 1dac3a9619
All of these changes do not apply on stable/3.0 due to either CLI
changes or another fix already being present.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
All PIM Neighbors for a given pim interface is registered with
BFD.
Upon receiving BFD status down event, PIM Neighbor with BFD info is deleted.
Add pim bfd configuraiton (CLI) per interface, '[no] ip pim bfd'
Testing Done:
Configure BFD under PIM interface on all neighbor routers,
check bfd sessions up, remote end unconfigure BFD, results in BFD session down.
Previous state was UP to New state DOWN, results in PIM neighbor delete behind
that particular pim interface.
Pim-smoke Results:
Ran 94 tests in 7409.680s
FAILED (SKIP=8, failures=2)
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
When we add a thread pointer to thread_add_XXX functions
when the specified function is called, thread.c is setting
the thread pointer to NULL. This was causing pim to
liberally pull it's zassert grenade pin's.
Additionally clean up code to not set the NULL pointer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
RFC2332 states that prefix length MUST be 0xff for unique bindings.
However, it seems at least some Cisco firmwares use host prefix
length instead (which on wire level makes sense). Relax the handling
of prefix length to treat all value longer than address length as
0xff. Additionally treat 0x00 the same way too, this is required
by the RFC. This also fixes the prefix length address family to be
checked against protocol address.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
eigrpd defines a bandwidth command that takes kilobits instead of
megabits which is problematic when installed in the same node as the
megabits command since (1-100000) and (1-10000000) are ambiguous
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Ensure that we have a valid vrf before we log
information about it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
The command 'debug ospf6 lsa unknown' was
always showing up, upon starting of the ospf6 daemon.
Remove this from happening. Also fix some help strings
while we are in there.
Ticket: CM-7913
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Basically if we are reading in a cli with a extended-nexthop
and we have not received from zebra the interface we are working
on I believe we have a race condition where we are not
propagating the PEER_FLAG_CAPABILITY_ENHE in this case.
Modify the code to propagate even if we haven't found the
interface yet.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
