bgpd crashes when there is several entries in the prefix-list. No
backtrace is provided because the issue was catched from a code review.
Fixes: 856ca177c4 ("Added json formating support to show-...-neighbors-... bgp commands.")
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
0x<address>FX was displayed instead of the prefix.
Fixes: b219dda129 ("lib: Convert usage of strings to %pFX and %pRN")
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Don't over-allocate syscaps in zcaps2sys(): This is just a single struct
(pset_t) with a count and a pointer to an array of capabilities, not an
array. So only allocate a single pset_t, not num copies of it.
The allocation size of syscaps->caps then needs to be based on the number of
Linux capabilities (count), but that is already handled properly a few lines
below.
Note that this fix is mostly cosmetic and for correctness. There was no
potential for memory corruption, because num is guaranteed to be nonzero. So
at least the one required pset_t was always allocated (but potentially much
more).
Signed-off-by: Martin Buck <mb-tmp-tvguho.pbz@gromit.dyndns.org>
This allows eliminating the superfluous yang_data object (which
is getting created used to call lyd_new_term then deleted). Instead
just call lyd_new_term() in the callback directly.
Signed-off-by: Christian Hopps <chopps@labn.net>
"ip/ipv6 protocol any route-map <route map>" cli is setting
wrong route type ( ZEBRA_ROUTE_MAX ), It should set route type
ZEBRA_ROUTE_ALL.
Ticket: #4101560
Signed-off-by: Sougata Barik <sougatab@nvidia.com>
newline is not expected to be printed in JSON outputs, e.g.:
```
"lastUpdate":{"epoch":1734490463,"string":"Wed Dec 18 04:54:23 2024\n"
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Issue: When the incoming config has say 30K entries of a prefix-lists,
current implementation is to schedule the configs to be batched and
only after batching the entire config, the processing of the configs
take place. As part of batching this config, we perform string
concatenation to save all the configs in the buffer which over time
results in taking longer time.
Ex: Imagine each line of config is 50 chars. With a delimiter of ‘- ‘ we end
up adding 52 chars to buffer for each command i.e. 52*30000 = 156K of chars.
Strlcat is an expensive operation and every time we strlcat, we have to
traverse at end of string to append new char.
Because of this, we end up adding extra 6-8 secs for accepting the config.
Fix: The idea here is to bring back something similar to the backoff
count implemented as part of 20e9a402 (lib: introduce configuration
back-off timer for YANG-modeled commands).
Essentially we keep a cap of 5000 per batch. So once 5000k config
commands are batched, we process them, clear the buffer, set the count
to 0 and then continue processing the rest of the config.
option1 file has 30K entries of prefix-list
Without Fix:
root@mlx-3700-20:mgmt:/var/log/raja/frr# time sudo vtysh -f option1
<SNIP>..............
Waiting for children to finish applying config...
[25191|staticd] done
[25189|watchfrr] done
[25178|ospfd] done
[25190|pbrd] done
[25181|bgpd] done
[25175|zebra] done
real 0m20.123s
user 0m9.384s
sys 0m2.403s
With Fix:
root@mlx-3700-20:mgmt:/var/log/raja/frr# time sudo vtysh -f option1
<SNIP>..............
Waiting for children to finish applying config...
[19887|staticd] done
[19885|watchfrr] done
[19886|pbrd] done
[19874|ospfd] done
[19877|bgpd] done
[19871|zebra] done
real 0m12.168s
user 0m7.511s
sys 0m1.981s
Issue: 3589101
Ticket# 3589101
Signed-off-by: Rajasekar Raja <rajasekarr@nvidia.com>
- WHen declaring macro scoped variables, can run into problem if the macro
variable passed in has the same name as the new variable introduced in the inner
scope. We don't get a warning and the uses will be wrong.
e.g.,
```
{
int __len = 10;
foo(__len); // => 10 and not 15 as we wanted.
}
```
Signed-off-by: Christian Hopps <chopps@labn.net>
- ran into problem with darr macros and nested macros using the same name
variables as passed in variables in an out scope. Make these macro scoped
variables more unique as well.
Signed-off-by: Christian Hopps <chopps@labn.net>
Modified ZEBRA_NEXTHOP_LOOKUP_MRIB to include the SAFI from which to do the lookup.
This generalizes the API away from MRIB specifically and allows the user to decide how it should do lookups.
Rename ZEBRA_NEXTHOP_LOOKUP_MRIB to ZEBRA_NEXTHOP_LOOKUP now that it is more generalized.
This change is in preperation to remove multicast lookup mode completely from zebra.
Signed-off-by: Nathan Bahr <nbahr@atcorp.com>
Without the fix:
```
show ip prefix-list test_1 10.20.30.96/27 first-match
<no result>
show ip prefix-list test_2 192.168.1.2/32 first-match
<no result>
```
With the fix:
```
ip prefix-list test_1 seq 10 permit 10.20.30.64/26 le 27
!
end
donatas# show ip prefix-list test_1 10.20.30.96/27
seq 10 permit 10.20.30.64/26 le 27 (hit count: 1, refcount: 0)
donatas# show ip prefix-list test_1 10.20.30.64/27
seq 10 permit 10.20.30.64/26 le 27 (hit count: 2, refcount: 0)
donatas# show ip prefix-list test_1 10.20.30.64/28
donatas# show ip prefix-list test_1 10.20.30.126/26
seq 10 permit 10.20.30.64/26 le 27 (hit count: 3, refcount: 0)
donatas# show ip prefix-list test_1 10.20.30.126/30
donatas#
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Currently the zapi reconnection is once every 10 seconds
for the first 3 times and then once every 60 seconds from then
on out. We are seeing interesting behavior under loaded systems
where zebra is just slow to come up and daemons are spending a long
time waiting to connect. Let's just make things a bit more aggressive.
Change the code to attempt to reconnect once every second for 30 seconds
and then change to once every 5 seconds from then on out.
This should help with non-integrated configuration on system startup.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
This would give more details why at some point we return deny, no match, etc.
Before this we have sometimes (I don't know why), e.g.:
```
Route-map: null, prefix: 192.168.2.0/24, result: deny
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Commit: 9112fb367b
Introduced the idea of setting the socket buffer
send/receive sizes. BSD's in general have the fun
issue of not allowing nearly as large as a size as
linux. Since the above commit was developed on linux
and not run on bsd it was never tested. Modify the
codebase to use the backoff setsockopt that we have
in the code base and use the returned values to allow
us to notice what was set and respond appropriately.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Currently if you have this sequence of events:
a) BGP starts
b) BGP reads cli that has bfd configuration
c) BGP attempts to install bfd configuration but fails because
zebra is not connected to yet
d) BGP connects to zebra
e) BGP receives resend bfd code from bfdd
f) BGP was not sending down the unsent data to bfd, never causing
the bfd session to be established.
So effectively bfd was attempting to install but failed
and then when it was asked to replay everything it decided
that the bfd information for a particular peer was actually
installed and does not need to be resent. Modify the code
such that the bfd code now tracks failed installation and
allows the resend of data to bfdd.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
In zebra_mpls.c it has a usage of MTYPE_NH_LABEL which is
defined in both lib/nexthop.c and zebra/zebra_mpls.c. The
usage in zebra_mpls.c is a realloc. This leads to a crash:
(gdb) bt
0 __pthread_kill_implementation (no_tid=0, signo=6, threadid=126487246404032) at ./nptl/pthread_kill.c:44
1 __pthread_kill_internal (signo=6, threadid=126487246404032) at ./nptl/pthread_kill.c:78
2 __GI___pthread_kill (threadid=126487246404032, signo=signo@entry=6) at ./nptl/pthread_kill.c:89
3 0x0000730a1b442476 in __GI_raise (sig=6) at ../sysdeps/posix/raise.c:26
4 0x0000730a1b94fb18 in core_handler (signo=6, siginfo=0x7ffeed1e07b0, context=0x7ffeed1e0680) at lib/sigevent.c:268
5 <signal handler called>
6 __pthread_kill_implementation (no_tid=0, signo=6, threadid=126487246404032) at ./nptl/pthread_kill.c:44
7 __pthread_kill_internal (signo=6, threadid=126487246404032) at ./nptl/pthread_kill.c:78
8 __GI___pthread_kill (threadid=126487246404032, signo=signo@entry=6) at ./nptl/pthread_kill.c:89
9 0x0000730a1b442476 in __GI_raise (sig=sig@entry=6) at ../sysdeps/posix/raise.c:26
10 0x0000730a1b4287f3 in __GI_abort () at ./stdlib/abort.c:79
11 0x0000730a1b9984f5 in _zlog_assert_failed (xref=0x730a1ba59480 <_xref.16>, extra=0x0) at lib/zlog.c:789
12 0x0000730a1b8f8908 in mt_count_free (mt=0x576e0edda520 <MTYPE_NH_LABEL>, ptr=0x576e36617b80) at lib/memory.c:74
13 0x0000730a1b8f8a59 in qrealloc (mt=0x576e0edda520 <MTYPE_NH_LABEL>, ptr=0x576e36617b80, size=16) at lib/memory.c:112
14 0x0000576e0ec85e2e in nhlfe_out_label_update (nhlfe=0x576e368895f0, nh_label=0x576e3660e9b0) at zebra/zebra_mpls.c:1462
15 0x0000576e0ec833ff in lsp_install (zvrf=0x576e3655fb50, label=17, rn=0x576e366197c0, re=0x576e3660a590) at zebra/zebra_mpls.c:224
16 0x0000576e0ec87c34 in zebra_mpls_lsp_install (zvrf=0x576e3655fb50, rn=0x576e366197c0, re=0x576e3660a590) at zebra/zebra_mpls.c:2215
17 0x0000576e0ecbb427 in rib_process_update_fib (zvrf=0x576e3655fb50, rn=0x576e366197c0, old=0x576e36619660, new=0x576e3660a590) at zebra/zebra_rib.c:1084
18 0x0000576e0ecbc230 in rib_process (rn=0x576e366197c0) at zebra/zebra_rib.c:1480
19 0x0000576e0ecbee04 in process_subq_route (lnode=0x576e368e0270, qindex=8 '\b') at zebra/zebra_rib.c:2661
20 0x0000576e0ecc0711 in process_subq (subq=0x576e3653fc80, qindex=META_QUEUE_BGP) at zebra/zebra_rib.c:3226
21 0x0000576e0ecc07f9 in meta_queue_process (dummy=0x576e3653fae0, data=0x576e3653fb80) at zebra/zebra_rib.c:3265
22 0x0000730a1b97d2a9 in work_queue_run (thread=0x7ffeed1e3f30) at lib/workqueue.c:282
23 0x0000730a1b96b039 in event_call (thread=0x7ffeed1e3f30) at lib/event.c:1996
24 0x0000730a1b8e4d2d in frr_run (master=0x576e36277e10) at lib/libfrr.c:1232
25 0x0000576e0ec35ca9 in main (argc=7, argv=0x7ffeed1e4208) at zebra/main.c:536
Clearly replacing a label stack is an operation that should be owned by
lib/nexthop.c. So lets move this function into there and have
zebra_mpls.c just call the function to replace the label stack.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
CID 1601478: Uninitialized variables (UNINIT)
Using uninitialized value "mbefore.real.tv_usec" when calling "event_consumed_time".
Fixes: 3e3a666331 ("lib: Add ability to track time in individual routemaps")
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Add the abilty to track how much time is spent in routemaps.
Example of the new output:
eva# show route-map
ZEBRA:
route-map: FOO Invoked: 1000000 (323 milliseconds total) Optimization: enabled Processed Change: false
deny, sequence 10 Invoked 1000000 (320 milliseconds total)
Match clauses:
Set clauses:
Call clause:
Action:
Exit routemap
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The `alloc` counter was tracking the current active
number of events in the system and if it went to
0 when freeing a new one it would assert. This
assert is a duplicate of what would happen with the
XFREE in the same situation. As such it is not
necessary.
Also remove the `event_master_free_unused` function
from the system.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
With commit:
60a3efec24
The ability for the wheel code to display the name of what
wheel was actually being run was removed from the system.
Since we can no longer do this and it's been 4 years since it's
been in, let's just remove this bit of dead code.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
