This code tries to summarize NSSA Type-7 LSAs using normal ranges
which are intended to summarize Type-3 LSAs only. This is not only
wrong, but the code is incomplete and lacking lots of things. Better
to remove it before implementing NSSA ranges correctly.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The iteration performed on ospf6_abr_unapprove_translates() was
wrong since AS-external LSAs are stored in the global LSDB and not
in the area LSDBs. As such, the "unapproved" flag wasn't being set
in any translated AS-external LSA, leading them to linger forever.
Fix the LSDB iteration and make the required changes to unset the
"unapproved" flag for AS-external LSAs that shouldn't be removed.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Change ospf6_get_nssa_fwd_addr() to try finding a global address
on any interface of the area and not on the first one only.
Additionally, do a micro-optimization in
ospf6_interface_get_global_address() to return as soon as a global
address is found.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Every received or originated LSA is automatically scheduled to be
refreshed periodically, there's no need to do that manually here.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The lsa->expire thread is for keeping track of when we
are expecting to expire(remove/delete) a lsa. There
are situations where we just decide to straight up
delete the lsa, but we are not ensuring that the
lsa is not already setup for expiration.
In that case just stop the expiry thread and
do the deletion.
Additionally there was a case where ospf6d was
just dropping the fact that a thread was already
scheduled for expiration. In that case we
should just setup the timer again and it will
reset it appropriately.
Fixes: #9721
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add the "default-information-originate" option to the "area X nssa"
command. That option allows the origination of Type-7 default routes
on NSSA ABRs and ASBRs.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The route created by the "default-information-originate" command
isn't a regular external route. As such, an NSSA ABR shouldn't
originate a corresponding Type-7 LSA for it (there's a separate
configuration knob to generate Type-7 default routes).
While here, fix a small issue in ospf6_asbr_redistribute_add()
where routes created by "default-information-originate" were being
displayed with an incorrect "unknown" type.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Fix wrong comparison since route->path.metric_type is always set
to either 1 or 2. The OSPF6_PATH_TYPE_EXTERNAL2 constant, whose
value is 4, refers to a route type so its usage was incorrect here.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Once NSSA is unconfigured on an area, all self-originated Type-7
LSAs need to be flushed. The existing code was iterating over the
LSDB in the wrong way, causing ospf6_nssa_flush_area() to flush
LSAs of all types. Use the ALL_LSDB_TYPED_ADVRTR macro to perform
the intended iteration correctly.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Once NSSA is unconfigured, the OSPF area should still be operational
as a normal area instead of being deleted.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
RFC 3101 - Section 2.1 says:
"(..) Interfaces associated with an NSSA will not send or receive
Type-5 LSAs on that interface but may send and receive Type-7 LSAs.
Therefore, if the N-bit is set in the options field, the E-bit must
be clear."
If the E-bit isn't cleared on an NSSA ABR, that will cause hello
packets to be dropped (due to parameters mismatch), which will
prevent the ABR from forming adjacencies with others routers in
the NSSA area.
This problem didn't affect the existing NSSA topotest by chance
of luck. In that topotest, in the NSSA ABR, the NSSA area is
configured before any interface is associated to it. That caused
ospf6_check_and_set_router_abr() to return false, leading to
the unsetting of the E-bit. With this fix, the order in which
areas/interfaces are configured shouldn't matter because the E-bit
will always be unset on NSSA areas.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
RCA: When Type-7 LSA is updated, the LSDB is searched, if the
LSA is present in the LSDB then the LSA is updated with next
sequence number and if not then it is originated with the
INITIAL sequence number.
Here while originating Type-7 LSA Process Level LSDB is searched
for instead of area level LSDB.
Fix: Search in the area level LSDB and not in the process level.
Fixes#9099
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
This is a requirement for avoiding sending traffic somewhere it was not
supposed to go: install summary route to local RIB to send traffic to
Null0.
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
Prefix options are per-prefix, not per-path. As evident by the fact
that the field is never used on ECMP paths. Move it where it belongs.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The ospf6_is_router_abr is checking to see if ospfv3 is an abr router
and also setting values. Let's rename it too `ospf6_check_and_set_router_abr`
to more accurately reflect what it is doing.
Additionally fix coverity #1505176 where we were not checking the return
value of ospf6_is_router_abr like we did every other time. In this
case we don't care about the return value so indicate that we do not.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The following is implemented.
1. Configuring area as NSSA.
2. Generating Type 7 LSA.
3. Conversion of Type 7 to Type 5 ( Default Behavior).
4. NSSA ABR selection.
Reviewed-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Co-authored-by: Kaushik <kaushiknath.null@gmail.com>
Co-authored-by: Soman K.S <somanks@gmail.com>
Signed-off-by: Kaushik <kaushiknath.null@gmail.com>
