Moving the common lines of pim_show_nexthop cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_neighbors_vrf_all cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_neighbors cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_local_membership cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_jp_agg cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_interface_vrf_all cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_interface cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_channel cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
The test for setting pimDesignatedRouterLocal was comparing
the result of pim_addr_cmp to non zero to say that the
pim_dr_addr and primary_address are the same. This is
not correct in that pim_addr_cmp returns 0 for being the
same, so the correct test is !pim_addr_cmp
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
PIM conformance test case 11.12 sends a register stop msg with
source address as 0. This should trigger a register stop for
all the upstreams. It is not happening as such because we are not
considering 0.0.0.0 source address for starg_handling.
Fixed it.
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
Prior to this fix, restarting the client just failed b/c the code tried to
"refresh" the existing LSA being added, except that code checked for meta-data
to exist, which was deleted when the client disconnected previously (or had
never connected and the LSA state was picked up from the network).
Signed-off-by: Christian Hopps <chopps@labn.net>
Reachable router information is used by OSPF opaque clients in order
to determine if the router advertising the opaque LSA data is
reachable (i.e., 2-way conectivity check).
Signed-off-by: Christian Hopps <chopps@labn.net>
The reachable router table is used by OSPF opaque clients in order to
determine if the router advertising the opaque LSA data is
reachable (i.e., 2-way conectivity check).
Signed-off-by: Christian Hopps <chopps@labn.net>
Only the multi-topology command can use 'ipv4-unicast' keyword to
configure standard topology.
The remaining code: dump from show commands, and yang definition,
uses 'standard' keyword instead.
The test have not been modified. The change would consists in
modifying test_fuzz_isis_tlv_tests.h.gz:
- replacing ipv4-unicast occurences with standard
\x69\x70\x76\x34\x2d\x75\x6e\x69\x63\x61\x73\x74
with
\x73\x74\x61\x6e\x64\x61\x72\x64
- align the buffer length by removing 4 bytes per occurence
Instead, a specific isis_mtid2str_fake() routing has been
put in place in isis_tlvs.c file.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
