Adds a knob that sets the time between loc-rib scans for conditional
advertisement.
I chose the range (5-240) because 1 second seems dumb and too easy to
hurt yourself at even moderate scale, 5 seconds you can still hurt
yourself but I could see a use case for it, and 4 minutes should be
enough for anyone (tm)
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Adds new commands to allow a user to default 'default' address-families
to be inherited by all new peers. Previously this was limited to just
ipv4/ipv6 unicast, now the full list is:
---
ipv4-unicast
ipv4-multicast
ipv4-vpn
ipv4-labeled-unicast
ipv4-flowspec
ipv6-unicast
ipv6-multicast
ipv6-vpn
ipv6-labeled-unicast
ipv6-flowspec
l2vpn-evpn
---
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Introduces bgp->default_af to selectively enable various default
afi/safis to be inherited by new peers.
Makes default_af flag logic consistent for all address-families, i.e.
instead of a "no default" flag for ipv4 and a "default" flag for ipv6,
just use "default" for both and make it true for ipv4 by default.
Removes old BGP_FLAG_NO_DEFAULT_IPV4 and BGP_FLAG_DEFAULT_IPV6, and
cleans up bgp->flags bit definitions to avoid gaps for unused bits.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Add a terse option to show bgp summary to shorten output.
Do not show the following information about the BGP
instances: the number of RIB entries, the table version and the used memory.
The "terse" option can be used in combination with the "remote-as", "neighbor",
"failed" and "established" filters, and with the "wide" option as well.
Before patch:
ubuntu# show bgp summary remote-as 123456
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
% No matching neighbor
Total number of neighbors 5
After patch:
ubuntu# show bgp summary remote-as 123456 terse
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 1
% No matching neighbor
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
When filtering sessions on show bgp summary with failed, established,
neighbor and remote-as options, add a counter of displayed neighbors
in addition to the total number of neighbor :
"Displayed neighbors X"
ubuntu# show bgp summary failed remote-as external
IPv4 Unicast Summary (VRF default):
Neighbor EstdCnt DropCnt ResetTime Reason
10.200.200.2 0 0 never Waiting for NHT
172.16.29.2 0 0 never Waiting for NHT
10.22.1.2 0 0 never Waiting for NHT
Displayed neighbors 3
Total number of neighbors 5
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
We are inconsistently using peer_establiahed(peer) with
sometimes using `peer->status == Established`. Just Convert
over to using the function for consistency.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Modify VRF/view display in show bgp summary:
- to be more concise
- to display on which VRF/view no neighbor was found
Before patch:
ubuntu# show bgp vrf all summary
Instance default:
IPv4 Unicast Summary:
BGP router identifier XX.XX.XX.XX, local AS number XXXX vrf-id 0
(...)
IPv6 Unicast Summary:
Instance private:
IPv4 Unicast Summary:
ubuntu# show bgp vrf all ipv4 multicast summary
% No BGP neighbors found
% No BGP neighbors found
After patch:
ubuntu# show bgp vrf all summary
IPv4 Unicast Summary (VRF default):
BGP router identifier XX.XX.XX.XX, local AS number XXXX vrf-id 0
(...)
IPv6 Unicast Summary (VRF default):
(...)
IPv4 Unicast Summary (VRF private):
(...)
ubuntu# show bgp vrf all ipv4 multicast summary
% No BGP neighbors found in VRF default
% No BGP neighbors found in VRF private
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
This commit add cli to check bgp's srv6 status
which is srv6-locator name and its locator-chunks
for bgpd. And this command also can be used to
check tovpn_sid for each bgp instances.
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
This commit add cil to configure BGP SRv6-VPN sid allocation.
Almost mechanism are based on BGP MPLS-VPN.
User can allocate and export sid with using following config.
Then bgpd try to allocate new SID to redirect vpn to vrf using
SRv6 localsid End.DT4/DT6. Currently linux kernel will regect
End.DT4 route install due to no-implementation.
(at-least today's FRR's ci kernel.)
So now we only supports BGP SRv6-VPNv6.
router bgp 1
segment-routing srv6
locator loc1
!
address-family ipv6 vpn
exit-address-family
!
router bgp 1 vrf vrf10
address-family ipv6 unicast
sid vpn export 1 !!(option1)!!
sid vpn export auto !!(option2)!!
exit-address-family
!
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
This commit add command to speficy SRv6 locator for BGP SRv6-VPN.
CLI example is follow. CLI block of "segment-routing" is already
implemented by previous commits and it's managed by zebra.
Zebra manage just the ownership of locator's prefix.
Zlient can request to get srv6-locator's prefix chunk using
srv6_manager_get_locator_chunk() which is usuful func to
execute ZEBRA_SRV6_MANAGER_GET_LOCATOR_CHUNK api. This request
is wokring as async, And zebra calls same api to Zclients when
zebra allocate locator prefix chunk.
And then, finally zclient(bgpd) catch the information via
process_srv6_lcoator_chunk callback function.
router bgp 1
segment-routing srv6
locator loc1
!
!
segment-routing
srv6
locators
locator loc1
prefix 2001:db8:1:1::/64
!
!
!
!
[POINT_OF_REVIEW]
In current implementation, user can just configure srv6 locator
but user can't de-configure srv6 locator.
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
This commit add base-lines for BGP SRv6 VPN support.
srv6_locator_chunks property of struct bgp is used
to store BGPd's own SRv6 locator chunk getting with
ZEBRA_SRV6_MANAGER_GET_LOCATOR_CHUNK api.
And srv6_functions is used to store BGP's srv6
localsids. It's mainly used when new SID reservation
from locator chunks.
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
base
The backoff code assumed that yang operations always completed quickly.
It checked for > 100 YANG modeled commands happening in under 1 second
to enable batching. If 100 yang modeled commands always take longer than
1 second batching is never enabled. This is the exact opposite of what
we want to happen since batching speeds the operations up.
Here are the results for libyang2 code without and with batching.
| action | 1K rts | 2K rts | 1K rts | 2K rts | 20k rts |
| | nobatch | nobatch | batch | batch | batch |
| Add IPv4 | .881 | 1.28 | .703 | 1.04 | 8.16 |
| Add Same IPv4 | 28.7 | 113 | .590 | .860 | 6.09 |
| Rem 1/2 IPv4 | .376 | .442 | .379 | .435 | 1.44 |
| Add Same IPv4 | 28.7 | 113 | .576 | .841 | 6.02 |
| Rem All IPv4 | 17.4 | 71.8 | .559 | .813 | 5.57 |
(IPv6 numbers are basically the same as iPv4, a couple percent slower)
Clearly we need this. Please note the growth (1K to 2K) w/o batching is
non-linear and 100 times slower than batched.
Notes on code: The use of the new `nb_cli_apply_changes_clear_pending`
is to commit any pending changes (including the current one). This is
done when the code would not correctly handle a single diff that
included the current changes with possible following changes. For
example, a "no" command followed by a new value to replace it would be
merged into a change, and the code would not deal well with that. A good
example of this is BGP neighbor peer-group changing. The other use is
after entering a router level (e.g., "router bgp") where the follow-on
command handlers expect that router object to now exists. The code
eventually needs to be cleaned up to not fail in these cases, but that
is for future NB cleanup.
Signed-off-by: Christian Hopps <chopps@labn.net>
Add ability to filter session on show bgp summary by neighbor or
remote AS:
ubuntu# show bgp summary ?
neighbor Show only the specified neighbor session
remote-as Show only the specified remote AS session
ubuntu# show bgp summary neighbor ?
A.B.C.D Neighbor to display information about
WORD Neighbor on BGP configured interface
X:X::X:X Neighbor to display information about
ubuntu# show bgp summary remote-as ?
(1-4294967295) AS number
external External (eBGP) AS sessions
internal Internal (iBGP) AS sessions
This patch includes the documentation and the topotest.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
This reverts commit 2cbd181ac9.
We also have "no neighbor WORD peer-group" command and it's impossible
to distinguish between those two commands if PGNAME is optional.
When only one of the keepalive or hold timers is changed from the
default, bgp won't print the timers command in the config.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
The leaf is called "no-replace-as" in the model but is used reversed in
all the code. Let's rename it to comply with the actual behavior.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Compile with v2.0.0 tag of `libyang2` branch of:
https://github.com/CESNET/libyang
staticd init load time of 10k routes now 6s vs ly1 time of 150s
Signed-off-by: Christian Hopps <chopps@labn.net>
Show alias name instead of numerical value in `show bgp <prefix>. E.g.:
```
root@exit1-debian-9:~/frr# vtysh -c 'sh run' | grep 'bgp community alias'
bgp community alias 65001:123 community-1
bgp community alias 65001:123:1 lcommunity-1
root@exit1-debian-9:~/frr#
```
```
exit1-debian-9# sh ip bgp 172.16.16.1/32
BGP routing table entry for 172.16.16.1/32, version 21
Paths: (2 available, best #2, table default)
Advertised to non peer-group peers:
65030
192.168.0.2 from home-spine1.donatas.net(192.168.0.2) (172.16.16.1)
Origin incomplete, metric 0, valid, external, best (Neighbor IP)
Community: 65001:12 65001:13 community-1 65001:65534
Large Community: lcommunity-1 65001:123:2
Last update: Fri Apr 16 12:51:27 2021
exit1-debian-9#
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
vtysh will return an informational message to the user that changing any
graceful-shutdown related parameter will require a peer reset. This is should
not be treated as an error message (resulting in a return code of 1) but
rather as a simple information to the user.
This fixes GitHub issue https://github.com/FRRouting/frr/issues/8403
$ vtysh -c configure -c 'router bgp 100' -c 'bgp graceful-restart'
Graceful restart configuration changed, reset all peers to take effect
$ echo $?
0
Signed-off-by: Christian Poessinger <christian@poessinger.com>
For whatever reason the dampening show run code was outside the normal
loop of code that handles the afi/safi portion. consolidate it into
the rest of the normal code.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
bgp_config_write_peer_af already checks to see if we are
a dynamic peer. No need to do so right before we call it.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When we are cycling through all peers and looking for
dampening data to dump, do not consider non-configed
peers( dopplegangers ).
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Problem Statement:
=================
In scale setup BGP sessions start flapping.
RCA:
====
In virtualized environment there are multiple places where
MTU need to be set. If there are some places were MTU is not set
properly then there is chances that BGP packets get fragmented,
in scale setup this will lead to BGP session flap.
Fix:
====
A new tcp option is provided as part of this implementation,
which can be configured per neighbor and helps to set the TCP
max segment size. User need to derive the path MTU between the BGP
neighbors and set that value as part of tcp-mss setting.
1. CLI Configuration:
[no] neighbor <A.B.C.D|X:X::X:X|WORD> tcp-mss (1-65535)
2. Running config
frr# show running-config
router bgp 100
neighbor 198.51.100.2 tcp-mss 150 => new entry
neighbor 2001:DB8::2 tcp-mss 400 => new entry
3. Show command
frr# show bgp neighbors 198.51.100.2
BGP neighbor is 198.51.100.2, remote AS 100, local AS 100, internal link
Hostname: frr
Configured tcp-mss is 150, synced tcp-mss is 138 => new display
4. Show command json output
frr# show bgp neighbors 2001:DB8::2 json
{
"2001:DB8::2":{
"remoteAs":100,
"bgpTimerKeepAliveIntervalMsecs":60000,
"bgpTcpMssConfigured":400, => new entry
"bgpTcpMssSynced":388, => new entry
Risk:
=====
Low - This is a config driven feature and it sets the max segment
size for the TCP session between BGP peers.
Tests Executed:
===============
Have done manual testing with three router topology.
1. Executed basic config and un config scenarios
2. Verified if the config is updated in running config
during config and no config operation
3. Verified the show command output in both CLI format and
JSON format.
4. Verified if TCP SYN messages carry the max segment size
in their initial packets.
5. Verified the behaviour during clear bgp session.
6. done packet capture to see if the new segment size
takes effect.
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
If a user issues the following commands:
```
router bgp 65000 vrf red
router bgp 65000 view red
```
bgpd ends up having NB config inconsistent with actual data.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
increase the maximum number of neighbors in a bgp group.
Set the maximum value to 50000 instead of 5000.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Instead of using bgp_get_default which refers to operational state, we
can check existence of the default node using only candidate config.
The same thing is done in "no router bgp" command.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
This new BGP configuration is akin to "bgp bestpath aspath
multipath-relax". When applied, paths learned from different peer types
will be eligible to be considered for multipath (ECMP). Paths from all
of eBGP, iBGP, and confederation peers may be included in multipaths
if they are otherwise equal cost.
This change preserves the existing bestpath behavior of step 10's result
being returned, not the result from steps 8 and 9, in the case where
both 8+9 and 10 determine a winner.
Signed-off-by: Joanne Mikkelson <jmmikkel@arista.com>
Remove old BFD API usage and replace it with the new one.
Highlights:
- More shared code: the daemon gets notified with callbacks instead of
having to roll its own code to find the notified sessions.
- Less code to integrate with BFD.
- Remove hidden commands to configure single / multi hop. Use
protocol data instead.
BGP can determine if a peer is single/multi hop according to the
following criteria:
a. If the IP address is a link-local address (single hop)
b. The network is shared with peer (single hop)
c. BGP is configured for eBGP multi hop / TTL security (multi hop)
- Respect the configuration hierarchy:
a. Peer configuration take precendence over peer-group
configuration.
b. When peer group configuration is removed, reset peer
BFD configurations to defaults (unless peer had specific
configs).
Example:
neighbor foo peer-group
neighbor foo bfd profile X
neighbor 192.168.0.2 peer-group foo
neighbor 192.168.0.2 bfd
! If peer-group is removed the profile configuration gets
! removed from peer 192.168.0.2, but BFD will still enabled
! because of the neighbor specific bfd configuration.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
