As netlink is available for all linux systems ( old linux distributions
are not considered), this commit removes the ipv6 ioctl support for
linux.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
It is possible to configure IPv6 addresses from interfaces by using
netlink socket, intead of using standard sockets.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
zserv.c had a grab bag of function declarations that
did not belong in it. Move those to where they better
belong.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
zserv.c has become a bit of a dumping ground for zebra cli.
I'd like to focus the zserv.c code into it's core functionality
which is handling the zapi interface.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The zebrad initialization does not need to be part of cli
initialization and should be done separately.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If the frr.conf file contains bgp unnumbered peering but the associated
interfaces do not have the commands "no ipv6 nd suppress-ra" and
"ipv6 nd ra-interval 10" configured, when frr-reload.py is issued the
interface commands are removed from the running config, causing peers to
got down and stay down after a link flap. This situation can occur if
the frr.conf file is created manually or via automation (like ansible)
but a subsequent "wr mem" has not been performed.
This fix changes the behavior so that the interface ipv6 nd ra commands
created by bgp are not displayed. Therefore, when the above condition
occurs, there is no difference between the running and stored configs
and peers work fine.
Ticket: CM-18702
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: CCR-7004
Testing-done: Manual testing successful. L3-smoke has no new failures
When we get a STREAM_GET failure of some sort we
need to handle the failure case here and safely
free up stored memory/context and return gracefully.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Some of the deprecated stream.h macros see such little use that we may
as well just remove them and use the non-deprecated macros.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
In some circumstances zebra and ldpd would display a pseudowire as UP
when in reality it's not (example: MTU mismatch between the two ends). Fix
this to avoid confusion.
Reported-by: ßingen <bingen@voltanet.io>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
When doing a route replace, on openbsd we were not
marking the old lsp as no longer installed, while
on linux we were. Move the abstraction up a layer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Setup a interface such that the add/del of lsp's from
the kernel can have a callback for success/failure.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When a route is installed or deleted into the kernel allow a
callback mechanism to handle the success/failure of
the kernel call.
This separation is to allow us to do these things:
1) In the future create a true pthread to handle route
install/deletes. This way we can schedule these
events in a smarter fashion
2) Allow us to use a common southbound api for route
install and deletion.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
zebra_find_client needs to match on instance as well so
protocols like ospfd will work correctly for notification.
Modify the zebra_find_client code to accept the instance
number and to pass it in appropriately.
Signed-off-by: Doanld Sharp <sharpd@cumulusnetworks.com>
Add a daemon that will allow us to test the zapi
as well as test route install/removal times from
the kernel.
The current commands are:
install route <starting ip address> nexthop <nexthop> (1-1000000)
This command starts installing at <starting ip address>/32
(1-100000) routes that it auto-increments by 1
Installation start time is noted in the log and finish
time is noted as well.
remove routes <starting ip address> (1-1000000)
This command removes routes at <starting ip address>/32
and removes (1-100000) routes created by the install route
command.
This code can be considered experimental and *is not*
something that should be run in a production environment.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we are installing into the kernel, not the
change points for notification to a higher level
protocol and make it happen
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow the higher level protocol to specify if it would
like to receive notifications about it's routes that
it has installed.
I've purposely made it part of zclient_new_notify because
we need to track the routes on a per daemon basis only.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Provide ZAPI code that can pass to an upper level protocol
what happened to it's route on install.
There are these notifications:
1) ZAPI_ROUTE_FAIL_INSTALL - The route attempted to be
installed did not work.
2) ZAPI_ROUTE_BETTER_ADMIN_WON - A route that was installed
has become un-installed due to another routing protocol
installing a better admin distance
3) ZAPI_ROUTE_INSTALLED - The route specified has been installed
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The rib_uninstall_kernel for non-UNICAST routes when
it is marking a route as no-longer installed should
actually mark it as uninstalled.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Rework of do_show_ip_route caused the 'show ip rpf'
cli to stop working. This put's it back into working
order.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The v6 linux kernel netlink code doees not have
route replace semantics. So if we are in that
situation, do a delete/add to get the correct
results.
Fixes: #1461
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
