The #if 0 code in ospfd, has not been compiled since at least
2012. If we are at least 9 years old at this point with no effort
to use or save, we should just get rid of it.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Implement the below 2 CLIs to clear the current data in the process
and neighbor data structure.
1. clear ip ospf process
2. clear ip ospf neighbor
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
No output when selecting a vrf
frr# show ip ospf vrf default database router adv-router 10.125.0.1
VRF Name: default
OSPF Router with ID (10.125.0.1)
In comparison with:
frr# show ip ospf database router adv-router 10.125.0.1
OSPF Router with ID (10.125.0.1)
Router Link States (Area 0.0.0.0)
LS age: 155
Options: 0x2 : *|-|-|-|-|-|E|-
(...)
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
When executing the following command to change the NSSA translator role
from OSPF_NSSA_ROLE_ALWAYS to OSPF_NSSA_ROLE_NEVER
r2(config-router)# area 1 nssa translate-never
During the time the `ospf_abr_nssa_check_status()` function is not executed,
we are in a situation where the role is OSPF_NSSA_ROLE_NEVER (just configured)
but the NSSATranslatorState is still ENABLED
During this time the output of "show ip ospf" displays the following:
r2# show ip ospf
Area ID: 0.0.0.1 (NSSA)
Shortcutting mode: Default, S-bit consensus: no
Number of interfaces in this area: Total: 1, Active: 1
It is an NSSA configuration.
Elected NSSA/ABR performs type-7/type-5 LSA translation.
We are an ABR and Number of fully adjacent neighbors in this area: 1 (**)
Basically the case TranslatorState=ENABLED && TranslatorRole=ROLE_NEVER is not
covered in `ospf_vty.c`
This PR adds the case TranslatorState=ENABLED and TranslatorRole=ROLE_NEVER
which should only happen for a small period of time
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
Areas created via interface command are not being deleted when
executing the command `no ip ospf area x`
With the following configuration:
!
interface eth1
ip address 10.0.12.2/24
ip ospf area 0.0.0.100
!
router ospf
!
r2# sh ip ospf
OSPF Routing Process, Router ID: 2.2.2.2
Supports only single TOS (TOS0) routes
....
Number of opaque AS LSA 0. Checksum Sum 0x00000000
Number of areas attached to this router: 1 <--- ***
Area ID: 0.0.0.100 <--- ***
Shortcutting mode: Default, S-bit consensus: ok
Number of interfaces in this area: Total: 1, Active: 1
Number of fully adjacent neighbors in this area: 0
Area has no authentication
Number of full virtual adjacencies going through this area: 0
SPF algorithm executed 1 times
Number of LSA 1
Number of router LSA 1. Checksum Sum 0x0000f3d4
Number of network LSA 0. Checksum Sum 0x00000000
Number of summary LSA 0. Checksum Sum 0x00000000
Number of ASBR summary LSA 0. Checksum Sum 0x00000000
Number of NSSA LSA 0. Checksum Sum 0x00000000
Number of opaque link LSA 0. Checksum Sum 0x00000000
Number of opaque area LSA 0. Checksum Sum 0x00000000
However when removing the area from the interface, the command
above displays the same information
r2# conf t
r2(config)# int eth1
r2(config-if)# no ip ospf area 0.0.0.100
r2(config-if)# exit
r2(config)# exit
r2# sh ip ospf
OSPF Routing Process, Router ID: 2.2.2.2
Supports only single TOS (TOS0) routes
....
Number of opaque AS LSA 0. Checksum Sum 0x00000000
Number of areas attached to this router: 1 <--- ***
Area ID: 0.0.0.100 <--- ***
Shortcutting mode: Default, S-bit consensus: ok
Number of interfaces in this area: Total: 0, Active: 0
Number of fully adjacent neighbors in this area: 0
Area has no authentication
Number of full virtual adjacencies going through this area: 0
SPF algorithm executed 2 times
Number of LSA 1
Number of router LSA 1. Checksum Sum 0x0000e26e
Number of network LSA 0. Checksum Sum 0x00000000
Number of summary LSA 0. Checksum Sum 0x00000000
Number of ASBR summary LSA 0. Checksum Sum 0x00000000
Number of NSSA LSA 0. Checksum Sum 0x00000000
Number of opaque link LSA 0. Checksum Sum 0x00000000
Number of opaque area LSA 0. Checksum Sum 0x00000000
r2# sh run
!
interface eth1
ip address 10.0.12.2/24
!
router ospf
!
end
This PR removes the area when executing `no ip ospf area` command
r2# sh ip ospf
OSPF Routing Process, Router ID: 2.2.2.2
Supports only single TOS (TOS0) routes
....
Number of opaque AS LSA 0. Checksum Sum 0x00000000
Number of areas attached to this router: 0
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
The following virtual-link configuration was not represented in the
running configuration:
area <area> virtual-link <ip> authentication [null|message-digest]
Signed-off-by: Duncan Eastoe <duncan.eastoe@att.com>
This commit tells the compiler we are intentionally ignoring
the lsa value returned and not doing anything with ret.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Description:
The below show command introduced to diplay all configured
summary addresss information along with matching corresponding
external route information.
show ip ospf [vrf <NAME|all>] summary-address [detail] [json]
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Description:
Added json support to ospf lsdb command and its subcommands.
Added json to the following sub commands.
show ip ospf database json
show ip ospf database router json
show ip ospf database network json
show ip ospf database external json
show ip ospf database summary json
show ip ospf database asbr-summary json
show ip ospf database nssa-external json
show ip ospf databas max-age json
show ip ospf database self-originate json
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Issue:
When the ospf area is changed from default to nssa or stub, the previously
advertised external LSAs are not removed from the neighbor.
The LSAs remain in database till maxage timeout.
Fix:
Advertise the external LSAs with age set to maxage and flood to the
nssa or stub area.
Signed-off-by: kssoman <somanks@gmail.com>
Use to-string functions for GR message codes instead of raw
string array indexing; the values used can come in packets
and are not validated.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Currently, only default area parameter is cleared, but we should do the
same for all area parameters with interface addresses.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Move ospf initialization to the actual place where it is created.
We don't need to do that every time "router ospf" is entered.
Also remove a couple of useless checks that can never be true.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
We should check for existing networks configuration before creating
if_params structure, or it leads to the memory leak.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
If we enter:
int eth0
ip ospf area 0
ip ospf 10 area 0
!
This will crash ospf. Prevent this from happening.
OSPF instances:
a) Cannot be mixed with non-instance
b) Are their own process.
Since in multi-instance world ospf instances are their own process,
when an ospf processes receives an instance command we must remove
our config( if present ) and allow the new config to be active
in the new process. The problem here is that if you have not
done a `router ospf` above the lookup of the ospf pointer will
fail and we will just crash. Put some code in to prevent a crash
in this case.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
This commit fixes the following behavior:
```
nfware(config)# interface enp2s0
nfware(config-if)# ip ospf area 0
nfware(config-if)# no ip ospf area 0
% [ospfd]: command ignored as it targets an instance that is not running
```
We should be able to use the command without configuring the instance.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Description:
The following show commands are added to display helper specific
information.
1.show ip ospf graceful-restart helper [detail] [json]
--> displays user configurations and list of all helpers details.
2.show ip ospf neighbour detail
--> diplays helper details
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
1. Ospf dead-interval will be set as 4 times of hello-interval, incase
if it is not set by using "ip ospf dead-interval <dead-val>".
2. On resetting hello-interval using "no ip ospf hello-interval" the
dead interval and hello due will be changed accordingly.
Signed-off-by: Kaushik <kaushik@niralnetworks.com>
OSPFD sends ARP proactively to speed up convergence for /32 networks
on a p2p connection. It is only an optimization, so it can be disabled.
It is enabled by default.
Signed-off-by: Jakub Urbańczyk <xthaid@gmail.com>
If you configure an area range in decimal format, the running
configuration displays it in dotted format.
Call ospf_area_display_format_set() for area range command,
as it is done for other variants.
Signed-off-by: Duncan Eastoe <duncan.eastoe@att.com>
Remove mid-string line breaks, cf. workflow doc:
.. [#tool_style_conflicts] For example, lines over 80 characters are allowed
for text strings to make it possible to search the code for them: please
see `Linux kernel style (breaking long lines and strings)
<https://www.kernel.org/doc/html/v4.10/process/coding-style.html#breaking-long-lines-and-strings>`_
and `Issue #1794 <https://github.com/FRRouting/frr/issues/1794>`_.
Scripted commit, idempotent to running:
```
python3 tools/stringmangle.py --unwrap `git ls-files | egrep '\.[ch]$'`
```
Signed-off-by: David Lamparter <equinox@diac24.net>
The command `area ... virtual-link ... retransmit-interval` supports
1-65535 range and the documentation already said
`ip ospf retransmit-interval` supports that, lets make the DEFUN to
accept that value.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
