Add a terse option to show bgp summary to shorten output.
Do not show the following information about the BGP
instances: the number of RIB entries, the table version and the used memory.
The "terse" option can be used in combination with the "remote-as", "neighbor",
"failed" and "established" filters, and with the "wide" option as well.
Before patch:
ubuntu# show bgp summary remote-as 123456
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
% No matching neighbor
Total number of neighbors 5
After patch:
ubuntu# show bgp summary remote-as 123456 terse
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 1
% No matching neighbor
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
similarly to what was done for IS-IS in commit 01d43141, combine
the SRGB and SRLB commands for OSPF-SR, so that we can replace
overlapping ranges in one sweep change.
Also allow the range configuration to be stored before SR is enabled.
There is no reason why we should not - in fact that constraint meant
that we were always requesting the default label ranges regardless
of what we actually wanted to use.
Finally, update the topotests now that we do not need to refresh
the SRGB/SRLB/MSD after disabling SR. Note that the prefix-sid still
needs to be re-added.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
Modify VRF/view display in show bgp summary:
- to be more concise
- to display on which VRF/view no neighbor was found
Before patch:
ubuntu# show bgp vrf all summary
Instance default:
IPv4 Unicast Summary:
BGP router identifier XX.XX.XX.XX, local AS number XXXX vrf-id 0
(...)
IPv6 Unicast Summary:
Instance private:
IPv4 Unicast Summary:
ubuntu# show bgp vrf all ipv4 multicast summary
% No BGP neighbors found
% No BGP neighbors found
After patch:
ubuntu# show bgp vrf all summary
IPv4 Unicast Summary (VRF default):
BGP router identifier XX.XX.XX.XX, local AS number XXXX vrf-id 0
(...)
IPv6 Unicast Summary (VRF default):
(...)
IPv4 Unicast Summary (VRF private):
(...)
ubuntu# show bgp vrf all ipv4 multicast summary
% No BGP neighbors found in VRF default
% No BGP neighbors found in VRF private
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add a minimum sphinx version requirement for the docs; RTD needs this to
know what version of sphinx to install.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
"ip nht resolve-via-default" is currently placed in "Link Parameters
Commands" section. Add a separate section and missing IPv6 counterpart.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Add ability to filter session on show bgp summary by neighbor or
remote AS:
ubuntu# show bgp summary ?
neighbor Show only the specified neighbor session
remote-as Show only the specified remote AS session
ubuntu# show bgp summary neighbor ?
A.B.C.D Neighbor to display information about
WORD Neighbor on BGP configured interface
X:X::X:X Neighbor to display information about
ubuntu# show bgp summary remote-as ?
(1-4294967295) AS number
external External (eBGP) AS sessions
internal Internal (iBGP) AS sessions
This patch includes the documentation and the topotest.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Compile with v2.0.0 tag of `libyang2` branch of:
https://github.com/CESNET/libyang
staticd init load time of 10k routes now 6s vs ly1 time of 150s
Signed-off-by: Christian Hopps <chopps@labn.net>
