The alias/description of an interface in linux was being
used to override the internal description. As such let's
fix the display to keep track of both if we have it.
Config in FRR:
!
interface docker0
description another combination
!
interface enp3s0
description BAMBOOZLE ME WILL YOU
!
Config in linux:
sharpd@robot ~/f/zebra> ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
alias This is the loopback you cabbage
2: enp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether 74:d0:2b:9c:16:eb brd ff:ff:ff:ff:ff:ff
alias HI HI HI
Now the 'show int descr' command:
robot# show int description
Interface Status Protocol Description
docker0 up down another combination
enp3s0 up up BAMBOOZLE ME WILL YOU
HI HI HI
lo up up This is the loopback you cabbage
Fixes: #4191
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Start using the dataplane for interface-address programming,
on netlink platforms. Other platforms just stubbed at this
point.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
The master thread handler is really part of the zrouter structure.
So let's move it over to that. Eventually zserv.h will only be
used for zapi messages.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
"brief" output for "show interface" helps when we have to quickly check
important information like ip address, vrf etc. This prints
information in the easy to read tabular format. Currently it prints oper
status, ifname, vrf, ipv4 and ipv6 addresses.
Ticket: CM-9109
Signed-off-by: Nitin Soni <nsoni@cumulusnetworks.com>
Even if the neighbor entry we want already exists, force its
reinstallation to ensure that it's valid. This will now take place when
we request an update of the neighbor entry.
Ticket: CM-22604
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
The interface type can be a bond or a bond slave, add some
code to note this and to display it as part of a show interface
command.
Signed-off-by: Dinesh Dutt <didutt@gmail.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Abstract the mac neigh installation for 169.254.0.1 into
it's own function that we can pass the mac address into.
This will allow a future commit to use this functionality
when we have the appropriate mac address from reading
optional attributes of a RA packet.
Signed-off-by: Donald Sharp <sharpd@cumuusnetworks.com>
The block comments from a couple commits were not following
proper style. Fix.
Fix SA warning that had snuck in.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Netdevices are not sorted in any fashion by the kernel during the initial
interface nldump. So you can get an upper device (such as an SVI) before
its corresponding lower device (bridge).
To fix this problem we skip resolving link dependencies during handling of
nldump notifications. Resolving instead at the end (when all the devices
are present)
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Ticket: CM-22388, CM-21796
Reviewed By: CCR-7845
Testing Done:
1. verified on a setup with missing linkages
2. automation - evpn-min
This crash occurs only with netns implementation.
vrf meaning is different regarging its implementation (netns or
vrf-lite)
- With vrf-lite implementation vrf is a property of the interface that
can be changed as the speed or the state (iproute2 command: "ip link
set dev IF_NAME master VRF_NAME"). All interfaces of the system are in
the same netns and so interface name is unique.
- With netns implementation vrf is a characteristic of the interface
that CANNOT be changed: it is the id of the netns where the interface
is located. To change the vrf of an interface (iproute2 command to
move an interface "ip netns exec VRF_NAME1 ip link set dev IF_NAME
netns VRF_NAME2") the interface is deleted from the old vrf and
created in the new vrf.
Interface name is not unique, the same name can be present in the
different netns (typically the lo interface) and search of interface
must be done by the tuple (interface name, netns id).
Current tests on the vrf implementation (vrf-lite or netns) are not
sufficient. In some cases (for example when an interface is moved from
a vrf X to the default vrf and then move back to VRF X) we can have a
corruption message and then a crash of zebra.
To avoid this corruption test on the vrf implementation, needed when an
interface changes, has been rewritten:
- For all interface changes except deletion the if_get_by_name function,
that checks if an interface exists and creates or updates it if
needed, is changed:
* The vrf-lite implementation is unchanged: search of the interface
is based only on the name and update the vrf-id if needed.
* The netns implementation search of the interface is based on the
(name, vrf-id) tuple and interface is created if not found, the
vrf-id is never updated.
- deletion of an interface (reception of a RTM_DELLINK netlink message):
* The vrf-lite implementation is unchanged: the interface
information are cleared and the interface is moved to the default
vrf if it does not belong to (to allow vrf deletion)
* The netns implementation is changed: only the interface
information are cleared and the interface stays in its vrf to
avoid conflict with interface with the same name in the default
vrf.
This implementation reverts (partially or totally):
commit 393ec5424e ("zebra: fix missing node attribute set in ifp")
commit e9e9b1150f ("lib: create interface even if name is the same")
commit 9373219c67 ("zebra: improve logs when replacing interface to an
other netns")
Fixes: b53686c52a ("zebra: delete interface that disappeared")
Signed-off-by: Thibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
when interface is a virtual ethernet interface, then there is no need to
update link pointer of interface.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This function is changed so that the interface index is searched across
the correct namespace.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This is the start of separating out the static
handling code from zebra -> staticd. This will
help simplify the zebra code and isolate static
route handling to it's own code base.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When I did a show ip route with `json` on a vrf when it didn't exist,
frr would output invalid json.
Signed-off-by: Nathan Van Gheem <nathan@cumulusnetworks.com>
Problem reported that if the vrf device is taken down and then brought
back up, any static route referencing that vrf device was not
re-installed. This fix runs back thru the static routes that
reference the vrf device coming up and re-install them.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
When zebra starts up it receives from the kernel a full dump of
interface information. Unfortunately it is in no particular order.
As such we sometimes receive data from the kernel about interfaces
we do not know about yet.
In this bug, we are attempting to use the interface pointer(->link)
for a vlan interface that we have not properly resolved.
This fix ensures that we will not attempt to call zvni_map_svi
if we have a NULL pointer. There are other places in the code
we are already checking for the fact that the ->link pointer
is valid before calling this function, so I believe that this
is correct.
We do need to come back and resolve all ->link pointers
after we have received the full table. This can be
done in another commit.
Ticket: CM-17041
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
There are cases when switching from one netns to an other one, where the
if_table registration by index has not been flushed. This fix mitigates
the potential crashes, in case the ifp->node pointer is null, the value
is overwritten by the route_node obtained.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Notice when someone deletes a neighbor entry we've put in for
rfc-5549 gets deleted by some evil evil person. When this happens
notice and push it back in, immediately.
Ticket: CM-18612
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The following types are nonstandard:
- u_char
- u_short
- u_int
- u_long
- u_int8_t
- u_int16_t
- u_int32_t
Replace them with the C99 standard types:
- uint8_t
- unsigned short
- unsigned int
- unsigned long
- uint8_t
- uint16_t
- uint32_t
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
When moving interfaces to an other place, like other netns, the
remaining interface is still present, with inactive status.
Now, that interface is deleted from the list, if the interface appears
on an other netns. If not, the interface is kept.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Because vrf with netns backend may be used, the correct zns must be
found prior any modifications.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
So as to get the correct NETNS where some discovery must be done and
populated, the zns pointer is directly retrieved from zvrf, instead of
checking that the VRF is a backend NETNS or not.
In the case where the interfaces are discovered before the VRF is enabled
( VRF-lite populate), then the default NS is retrieved.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
this is a static analysis performed by c-lang scan-build tool that
demonstrated this issue. This commit is handling the fix.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
