Because vrf backend may be based on namespaces, each vrf can
use in the [16-(2^32-1)] range table identifier for daemons that
request it. Extend the table manager to be hosted by vrf.
That possibility is disabled in the case the vrf backend is vrflite.
In that case, all vrf context use the same table manager instance.
Add a configuration command to be able to configure the wished
range of tables to use. This is a solution that permits to give
chunks to bgp daemon when it works with bgp flowspec entries and
wants to use specific iptables that do not override vrf tables.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Added references to some other sysctl knobs that influence behavior
significant to routers, e.g. arp_accept, arp_ignore, bc_forwarding.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
1. This check is absolutely useless. Nothing keeps user from deleting
the address right after this check.
2. This check prevents zebra from correctly reading the user config with
"set src" because of a race with interface startup (see #4249).
3. NO OPERATIONAL DATA USAGE ON VALIDATION STAGE.
Fixes#7319.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
"ip nht resolve-via-default" is currently placed in "Link Parameters
Commands" section. Add a separate section and missing IPv6 counterpart.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Description:
Added a new show command("show ip zebra route dump") to dump all routes
with detailed information including nexthops,flags, status ..etc.
This helps for dubugging and added to support_bundle_command.conf.
Defined this command as a hidden command.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
These don't need to be documented, most of the time they are obvious,
when they aren't the behavior can just be described in the command
description.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
- Generate index entries automatically
- Remove manual command index entries
- Clean up a few other manual index entries
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
People keep asking about the default unreachable route
in the linux vrf table. Add a bit of color about the
design choices and what is going on.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Many index entries used '[no] xxx' or 'no xxx', some had both
positive and 'no' forms. Clean that up mostly - index positive
form of commands only.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Add a command that allows FRR to know it's being used with
an underlying asic offload, from the linux kernel perspective.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add a type specifier to the `show nexthop-group` command
so we can easily filter by type when using proto created
nexthop groups.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
With the change of Solaris going from Supported -> UnSupported
the documentation needed to be updated to reflect the reality
on the ground.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
* add a vrf sub-command `[no] ipv6 router-id X:X::X:X`.
* add command `[no] ipv6 router-id X:X::X:X [vrf NAME]` for backward
compatibility.
* add a vrf sub-command `[no] ip router-id A.B.C.D` and make the old
one without `ip` an alias for it.
* add a command `[no] ip router-id A.B.C.D [vrf NAME]` for backward
comptibility and make the old one without `ip` an alias for it.
* add command `show ip router-id [vrf NAME]` and make
the old one without `ip` an alias for it.
* add command `show ipv6 router-id [vrf NAME]`.
* add ZAPI commands `ZEBRA_ROUTER_ID_V6_ADD`,
`ZEBRA_ROUTER_ID_V6_DELETE` and `ZEBRA_ROUTER_ID_V6_UPDATE`
for deamons to get notified of the IPv6 router-id.
* update zebra documentation.
Signed-off-by: Sebastien Merle <sebastien@netdef.org>
Include an IPv6 example for set src
And a note that the IP address has to exist. This is to try and make
people aware to avoid things like issue #4249https://github.com/FRRouting/frr/issues/4249
Signed-off-by: Tim Bray <tim@kooky.org>
router-id is buried deep in "show running-config", this new
command makes it easy to retrieve the user configured router-id.
Example:
# configure terminal
(config)# router-id 1.2.3.4
(config)# end
# show router-id
router-id 1.2.3.4
# configure terminal
(config)# no router-id 1.2.3.4
(config)# end
# show router-id
#
Signed-off-by: Jafar Al-Gharaibeh <jafar@atcorp.com>
Add some doc information for the new nexthop group commands. Also
had to add some for ones that were missing, which we are adding
additional commands to.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
The FRR documentation had no discussion about how Administrative
Distance is used. Update the documentation to reflect the reality
on the ground.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add notes to several docs about the limits to FRR's current
MPLS-TE support, which is limited to some routing protocol
LSA/TLV support. It wasn't very clear that FRR does not offer
a complete TE/RSVP-TE solution at this time.
Also removed some stale info about configure script options.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
the documentation of zebra is appended with that command.
PR=61261
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Acked-by: Thibaut Collet <thibaut.collet@6wind.com>
The -N <namespace> option is now used to control the location
of various control files and sockets. Update the documentation
to reflect this.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This code doees this:
a) Imagine ospf installs a route into zebra. Zebra crashes and
we restart FRR. If we are using the -k option on zebra than
all routes are re-read in, including this OSPF route.
b) Now imagine at the same time that zebra is starting backup
ospf on a different router looses a link to the this route.
c) Since zebra was run with -k this OSPF route is read back
in but never replaced and we now have a route pointing out
an interface to other routers that cannot handle it.
We should never allow users to implement bad options from zebra's
perspective that allow them to put themselves into a clear problem
state and additionally we have *absolutely* no mechanism to ever
fix that broken route without special human interaction.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
<Initial Code from Praveen Chaudhary>
Add the a `--graceful_restart X` flag to zebra start that
now creates a timer that pops in X seconds and will go
through and remove all routes that are older than startup.
If graceful_restart is not specified then we will just pop
a timer that cleans everything up immediately.
Signed-off-by: Praveen Chaudhary <pchaudhary@linkedin.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Noticed that a couple of the `show zebra ...` commands are missing
from the zebra documentation that I use a bunch. Let's add them
in.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This command is broken and has been broken since the introduction
of vrf's. Since no-one has complained it is safe to assume that
there is no call for this specialized linux command. Remove
from the system with extreme prejudice.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
It is possible to dynamically change default VRF name, if vrf backend is
a netns backend. By creating a link to the default netns in
/var/run/netns folder, then the file name will be used to name the
default VRF. If no backend netns is chosen, it is explained that it is
still possible to statically configure the default vrf name to new
define.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Remove the ip route specific sections from zebra documenation and
create a specific one for the new staticd.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The parameter was missing in that vty command. Then it is being added.
Also some documentation is refreshed.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Keeping the config intact might be misunderstood. I say that even if VRF
netns is automatically discovered, it is possible for administrator to
save the netns information in the config file, to bring more clarity (
hence the config commands available).
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
To avoid some confusions, it is precised in the documentation that
the configuration not done from zebra will not be injected in the
configuration context. As consequence, the config file will not be
impacted by underlying network context. But also, this will not be
possible for *Zebra* to attempt to modify outside networking objects.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
As there are subtle differences between VRF-lite and VRF-netns,
some information is given to the operator on what can be/ can not be
done.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Explain the --enable-ecmp=X configure option as well as
modify the zebra user doc to explain the -e X option.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* Run sphinxcontrib-spelling over docs
* Correct spelling errors
* Compile a dictionary for future spellchecking efforts
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Short and long form options can be written on the same line, Sphinx
understands how to cross-reference using either one of them. Also
replace some - with _ where appropriate.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
