Fix details :
Added a utility cli to generate a igmp query on an interface.
This won't impact the existing query generation based on the
general query interval.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
In a pim-evpn setup (say TORC11<=>TORC12) an mroute can have a mix of
PIM and IGMP joins. The vxlan termination device ipmr-lo is IGMP
joined on termination mroutes and the peerlink-rif can be pim joined
on the same mroute if the MLAG peer (TORC11) loses all its uplinks to
underlay -
root@TORC12:~# net show pim state 239.1.1.101|grep pimreg
1 * 239.1.1.101 uplink-1
pimreg(I ), ipmr-lo( J ), peerlink-3.4094( J )
root@TORC12:~#
When the uplinks come back up on TORC11 it will prune the peerlink-rif
and join the RP (say spine) via the uplinks.
TORC12 is rxing the prune and removing the if_channel
(pim_ifchannel_delete). However it is not removing the OIF from
mfcc_ttl basically leaving behind a leaked OIF in the forwarding
entry. And this is because it is deriving the owner flag from the
parent upstream entry and incorrectly concluding that all OIFs are
IGMP joined.
Thix fix flushes out both PIM and IGMP ownership when the ifchannel is
deleted.
There is a second fix in the commit and that is to set the proto mask
correctly (to STAR) for inherited OIFs. (S,G) entries can inherit the
OIF from the (*, G) entry and this decision can change when the pim/igmp
ifchannel is removed. The earlier code was setting the proto-mask
incorrectly to PIM or IGMP.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
(cherry picked from commit d4d1d968dbbe61347393f7dace8b675496ff1024)
When a link goes down the vifi was being deleted but the OIF stayed
in the OIL with a stale vifi -
oroot@act-7726-03:~# net show pim state
Codes: J -> Pim Join, I -> IGMP Report, S -> Source, * -> Inherited from (*,G), V -> VxLAN
Installed Source Group IIF OIL
1 * 239.1.1.111 swp1s1 pimreg(I ), ipmr-lo( J )
1 6.0.0.28 239.1.1.111 lo pimreg( J ), ipmr-lo( *), swp1s1( J )
root@act-7726-03:~# ip link set swp1s1 down
root@act-7726-03:~# net show pim state
Codes: J -> Pim Join, I -> IGMP Report, S -> Source, * -> Inherited from (*,G), V -> VxLAN
Installed Source Group IIF OIL
1 * 239.1.1.111 swp1s0 pimreg(I ), ipmr-lo( J )
1 6.0.0.28 239.1.1.111 lo ipmr-lo( *), swp1s0( J ), <oif?>( J ) >>>>>>>>
root@act-7726-03:~#
The problem was as a part ifchannel_delete the join state of the channel
was checked to avoid incorrect OIF deletion this was preventing the OIF
from being flushed. Fix is to flip the channel join-state to NOINFO before
deleting it.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
There has never been a `debug igmp trace detail` but we have
had code to display this when we had the appropriate flags
set. Since we never can accept this, let's remove this.
This showed up because of commit:0ab16492d2d9fcc6cba7e001227deed6765ed261
where we re-arranged some debugs to combine them being turned on.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Position of address family and encoding type is defined wrongly in the
packed structure. This will correct the position as per RFC 4601 4.9.1
Signed-off-by: Saravanan K <saravanank@vmware.com>
If we create a channel_oil ensure that all paths that
we can go down will create one. Future commits
can remove the (up->channel_oil) tests.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
There is no need to check for ALLOC function failures
in the code base. If we cannot get more memory we
assert.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The vifi being displayed is just confusing. Display the
actual interface name being used in the mroute.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This is mostly relevant for Solaris, where config.h sets up some #define
that affect overall header behaviour, so it needs to be before anything
else.
Signed-off-by: David Lamparter <equinox@diac24.net>
In Scenario where receiver is present in a subnet where 2 or more pim mrouters.
When IGMP query received on a DR interface and RP is reachable through non DR.
Currently we are blocking to create upstream where iif == oif. So pim join
not generated towards RP. We have to allow the DR router in the network to create an upstream.
Signed-off-by: Saravanan K <saravanank@vmware.com>
clippy can't process #ifdef or similar bits inside of an argument list
(e.g. within the braces of a DEFUN or DEFPY statement.) Improve error
reporting to catch these cases instead of generating broken C code.
Fixes: #3840
Signed-off-by: David Lamparter <equinox@diac24.net>
Field vrf_id is replaced by the pointer of the struct vrf *.
For that all other code referencing to (interface)->vrf_id is replaced.
This work should not change the behaviour.
It is just a continuation work toward having an interface API handling
vrf pointer only.
some new generic functions are created in vrf:
vrf_to_id, vrf_to_name,
a zebra function is also created:
zvrf_info_lookup
an ospf function is also created:
ospf_lookup_by_vrf
it is to be noted that now that interface has a vrf pointer, some more
optimisations could be thought through all the rest of the code. as
example, many structure store the vrf_id. those structures could get
the exact vrf structure if inherited from an interface vrf context.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
vrf_id parameter is replaced with struct vrf * parameter. It is
needed to create vrf structure before entering in the fuction.
an error is generated in case the vrf parameter is missing.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
the vrf_id parameter is replaced by struct vrf * parameter.
this impacts most of the daemons that look for an interface based on the
name and the vrf identifier.
Also, it fixes 2 lookup calls in zebra and sharpd, where the vrf_id was
ignored until now.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The pim ifchannel expiry timer was not setting any debug output.
Let's add something in to help us understand what is going on.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We already log whether or not we add nht tracking, having
an additional boolean to say to log another line is
a bit over the top.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
While this is impossible, make the compilers a bit happier
for those of us having to use something old.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com
Various compilers in our CI system were complaining about various
auto-conversions. Let's get these cleaned up a bit more.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When pim is started and has nothing to talk to zebra about
over the zlookup socket and interface events are happening
then the zlookup socket is not being drained.
This eventually leads to a situation where the kernel send buffer
fills up and zebra is unable to write anything down the pipe.
At this time the zapi starts buffering data in `struct buffer`
which of course slowly fills up as pim has nothing to do.
As a bit of a hack allow the zlookup socket to wake up 1 time
a minute and ask for information about the default route
and do nothing with it. This will cause the socket buffers
to be drained and the system will be happy.
Long term we need to get rid of this synchronous/asynchronous
duality that pim has. This is on the radar but is not something
that could be fixed in an afternoon or a week of effort in my
opinion. Given time constraints right now. Let's put this
in place and then once we get pim completely async then
we can just remove the zlookup( I hope ) code.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
A couple of places of strncpy snuck in due to my confusion
about if Quentin's earlier change had gotten in. Just some
code in flux. This should fix the issue/warnings in our
CI system.
Recent commits rewrote the `clear mroute` command and this caused
these two two functions to no longer be used, remove.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The header inclusion in mtracebis.c should include zebra.h
and not config.h. There are other issues that need to
be worked through as well, but we can do this in the future.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Introduce new cli commands ip igmp last-member-query-count <1-7>
ip igmp last-member-query-interval <1-255> deciseconds.
Display the config in show running config and show ip igmp interface
Signed-off-by: Sarita Patra <saritap@vmware.com>
Introduced a new command "show ip mroute summary"
to display total number of (*, G) and (S, G) mroutes
created and number of mroutes installed in the kernel.
Signed-off-by: Sarita Patra <saritap@vmware.com>
Made changes to clean up the all upstreams and ifchannels
in FRR apart from cleanup datapath mroutes when this command
issued.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Fix: When RP receives a (*, G) join and corresponding (s,g)
is present, then check for OIL is not-empty, then only switch
upstream (s, g) state to JOINED.
Signed-off-by: Sarita Patra <saritap@vmware.com>
This would show only bsm related statistics for now.
We shall add more statistics to this later.
Sw3# show ip pim statistics
BSM Statistics :
----------------
Number of Received BSMs : 1584
Number of Forwared BSMs : 793
Number of Dropped BSMs : 1320
Interface : ens192
-------------------
Number of BSMs dropped due to config miss : 0
Number of unicast BSMs dropped : 0
Number of BSMs dropped due to invalid scope zone : 0
Interface : ens224
-------------------
Number of BSMs dropped due to config miss : 0
Number of unicast BSMs dropped : 0
Number of BSMs dropped due to invalid scope zone : 0
Interface : ens256
-------------------
Number of BSMs dropped due to config miss : 0
Number of unicast BSMs dropped : 0
Number of BSMs dropped due to invalid scope zone : 0
Signed-off-by: Saravanan K <saravanank@vmware.com>
This command shows all the fragments of the last received preferred BSM.
This displayed in readable format.
Sw3# sh ip pim bsm-database
Scope Zone: Global
Number of the fragments: 1
BSM Fragment : 1
------------------
BSR-Address BSR-Priority Hashmask-len Fragment-Tag
30.0.0.100 0 0 3289
Group : 225.1.1.1/32
-------------------
Rp Count:9
Fragment Rp Count : 9
RpAddress HoldTime Priority
20.0.0.2 150 0
2.2.2.2 150 0
9.9.9.10 150 0
7.7.2.7 150 0
7.2.2.7 150 0
7.7.9.7 150 0
7.8.9.10 150 0
7.5.2.7 150 0
9.10.9.10 150 0
Group : 226.1.1.1/32
-------------------
Rp Count:1
Fragment Rp Count : 1
RpAddress HoldTime Priority
9.9.9.9 150 0
Signed-off-by: Saravanan K <saravanank@vmware.com>
If no_fwd bit not set,
forward on all interfaces including which it came.
store it in bsm list with size for forwarding it later to new neighbor.
calculate PIM mtu of the interface, if bsm size is more do sematic frag and send
Signed-off-by: Saravanan K <saravanank@vmware.com>
When all rp received on a partial list, this routine is called.
if static rp configured for the group range
if partial list is empty
clean main list and partial list
else
replace main with partial and start the g2rp timer with head of new main
return
if main list was empty
call rp new with head of partial list and start g2rp timer.
else
if partial list is empty
call rp del
else
stop g2rp timer of old elected rp.
call rp change with new rp(head of partial list) and start g2rp timer.
swap the lists and clean the old list(now partial list).
Signed-off-by: Saravanan K <saravanank@vmware.com>
Bootstrap rp table is route_table datastructure with group range as key.
Each node represents a group range.
Every node has two lists of rp nodes. partial list and active list(bsrp_list)
Whenever a rp is parsed from BSM, it is updated to partial list.
When partial list is full, we move it to main list(bsrp_list). This commit doesn't cover that.
Rp Election routine based on RFC 7761 Sec 4.7
Hash calculation for rp election based on RFC 7761 Sec 4.7.2
Signed-off-by: Saravanan K <saravanank@vmware.com>
1. Packet validation as per RFC 5059 Sec 3.1.3
We won't supporting scope zone BSM as of now, they are dropped now.
Order of the check slightly be changed in code for optimization.
if ((DirectlyConnected(BSM.src_ip_address) == FALSE) OR
(we have no Hello state for BSM.src_ip_address)) {
drop the Bootstrap message silently
}
if (BSM.dst_ip_address == ALL-PIM-ROUTERS) {
if (BSM.no_forward_bit == 0) {
if (BSM.src_ip_address != RPF_neighbor(BSM.BSR_ip_address)) {
drop the Bootstrap message silently
}
} else if ((any previous BSM for this scope has been accepted) OR
(more than BS_Period has elapsed since startup)) {
#only accept no-forward BSM if quick refresh on startup
drop the Bootstrap message silently
}
} else if ((Unicast BSM support enabled) AND
(BSM.dst_ip_address is one of my addresses)) {
if ((any previous BSM for this scope has been accepted) OR
(more than BS_Period has elapsed since startup)) {
#the packet was unicast, but this wasn't
#a quick refresh on startup
drop the Bootstrap message silently
}
} else {
drop the Bootstrap message silently
}
2. Nexthop tracking registration for BSR
3. RPF check for BSR Message.
Zebra Lookup based rpf check for new BSR
NHT cache(pnc) based lookup for old BSR
Signed-off-by: Saravanan K <saravanank@vmware.com>
This commit includes parsing of Nbit and contructing pim hdr with Nbit
Adding Nbit to PIm hdr structure
Adding Scope zone bit and Bidir bit to Encoded IPv4 Group Address
Signed-off-by: Saravanan K <saravanank@vmware.com>
When bs time out occurs,
1. Delete the bsm list
2. Reset the BSR address
3. delete nexthop tracking for the expired BSR
4. Give one more lease of life to all the bsr advertised rp with hold time
5. clear partial list of each grp node if not empty
Signed-off-by: Saravanan K <saravanank@vmware.com>
DS Overview:
Bootstrap RP table has grp node.
scope --> rp table --> grp node1 --> rp list --> rp nodes(g2rp timer)
|
-------> grp node2 --> rp list --> rp nodes(g2rp timer)
When grp2rp mapping expires, following has to be done.
1. delete the rp node from the active bs-rp list in the list
2. calculate the elapsed time for other rp nodes in the list
3. delete those nodes having more elapse time than their hold time
4. If the list is not empty and current rp src is not static
rp change with new rp(head) & start g2rp timer with value holdtime - elapse
5. If the list is empty and current rp src for the grp is not static
delete the rp
6. If the list is not empty and current rp is static, just start the
g2rp timer with value holdtime - elapse
7. If list is empty and pending list is empty, delete grp node.
Note: g2rp timer will be run only on elected RP node for optimization.
when it expires, other node are update with elapse time.
This list is sorted insuch way that elected RP is the HEAD of list
Signed-off-by: Saravanan K <saravanank@vmware.com>
Command to display current bsr, last received bsm ts, bsr uptime
Sw3# sh ip pim bsr
PIMv2 Bootstrap information
Current preferred BSR address: 30.0.0.100
Priority Fragment-Tag State UpTime
0 6390 ACCEPT_PREFERRED 91:26:24
Last BSM seen: 00:00:37
Signed-off-by: Saravanan K <saravanank@vmware.com>
pim_rp_new split into pim_rp_new_config and pim_rp_new.
pim_rp_new_config is called by CLI.
pim_rp_new will be called by pim_rp_new_config and bsm rp config.
pim_rp_del is split into pim_rp_del_config and pim_rp_del
pim_rp_del_config is called by CLI.
pim_rp_del is called by pim_rp_del_config and bsm rp config
Signed-off-by: Saravanan K <saravanank@vmware.com>
(intf)ip pim bsm - to enable bsm processing on the interface
(intf)no ip pim bsm - to disable bsm processing on the interface
(intf)ip pim unicast-bsm - to enable ucast bsm processing on the interface
(intf)no ip pim unicast-bsm - to disable ucast bsm processing on the interface
Note: bsm processing and ucast bsm processing is enabled by default on a
pim interface. The CLI is implemented as a security feature as recommended by
RFC 5059
Signed-off-by: Saravanan K <saravanank@vmware.com>
Sw3# sh ip pim rp-info
RP address group/prefix-list OIF I am RP Source
20.0.0.2 225.1.1.1/32 ens192 no BSR
9.9.9.9 226.1.1.1/32 (Unknown) no BSR
30.0.0.100 229.1.1.5/32 ens192 no Static
Signed-off-by: Saravanan K <saravanank@vmware.com>
For each BSM packet, rpf check is performed. We will be accepting if the
source address match any of the next hop neighbor(in ecmp case) to reach
the Bootstrap Router.
1. pim_nexthop_match - this lookup in zebra and return true if any of the
next hop nbr is matching (in ecmp case).
2. pim_nexthop_match_nht_cache - this api searches the given address in local
pnc and return true if any of the next hop
nbr is matching (in ecmp case).
Signed-off-by: Saravanan K <saravanank@vmware.com>
Apart from datastructure, bsm scope initialization and deinitialiation
routines called during pim instance init and deinit. Also makefile changes.
Signed-off-by: Saravanan K <saravanank@vmware.com>
It doesn't make much sense for a hash function to modify its argument,
so const the hash input.
BGP does it in a couple places, those cast away the const. Not great but
not any worse than it was.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
bfd cbit is a value carried out in bfd messages, that permit to keep or
not, the independence between control plane and dataplane. In other
words, while most of the cases plan to flush entries, when bfd goes
down, there are some cases where that bfd event should be ignored. this
is the case with non stop forwarding mechanisms where entries may be
kept. this is the case for BGP, when graceful restart capability is
used. If BFD event down happens, and bgp is in graceful restart mode, it
is wished to ignore the BFD event while waiting for the remote router to
restart.
The changes take into account the following:
- add a config flag across zebra layer so that daemon can set or not the
cbit capability.
- ability for daemons to read the remote bfd capability associated to a bfd
notification.
- in bfdd, according to the value, the cbit value is set
- in bfdd, the received value is retrived and stored in the bfd session
context.
- by default, the local cbit announced to remote is set to 1 while
preservation of the local path is not set.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The route_map_event_hook callback was passing the `route_map_event_t`
to each individual interested party. No-one is ever using this data
so let's cut to the chase a bit and remove the pass through of data.
This is considered ok in that the routemap.c code came this way
originally and after 15+ years no-one is using this functionality.
Nor do I see any `easy` way to do anything useful with this data.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
become stale entries.
Topology:
--------
Source
|
FHR
|
RP ------ LHR --- Recv1
|
Recv2
Root case :
-----------
When RP acts as a LHR i.e RP has a local receiver and registed for
the same group where LHR connected receiver also registered for the
same multicast group.When RP receives a (s,g) join form LHR , it
increments upstream ref count to two to track the Local membership
as well.But at the time of KAT expiry in RP , upstream reference
is not being removed Which is added to track local membership which
is causing to make these entries as stale in RP and FHR.
Fix : Made the change such that it removes the upstream reference
if it is added to track the local memberships.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
vrf_id parameter is added to the api of bfd_client_sendmsg().
this permits being registered to bfd from a separate vrf.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This macro:
- Marks ZAPI callbacks for readability
- Standardizes argument names
- Makes it simple to add ZAPI arguments in the future
- Ensures proper types
- Looks better
- Shortens function declarations
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
There exists a possiblity that we have upstream data but
at this point in time the rpf failed because there is no
path. As such the rpf interface will be NULL and we
should not necessarily trust it. Prevent a crash
Ticket: CM-24857
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
So when we remove a ifchannel from the system we should check to
see if we still care about the S,G having it in the OIL still
due to inheritance rules. The deletion does not necessarily
mean it should not be in the OIL for the S,G.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
the json code has not been updated since a variety of new flags have
been added to the code base. Add those flags in so we can tell
what is going on sometimes.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add the ability to select on a S or G for a `show ip mroute`
command.
show ip mroute 225.1.1.111
show ip mroute 4.5.6.7 225.1.1.111
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Always when creating a new S,G state look at all possible ifchannels
to decide what the mroute should be.
The bug that this is fixing is this:
Suppose two incoming `*,G` joins on swp1, and swp2.
Now suppose that one of those ifchannel `*,G` sends a `*,G S,G RPT Prune`.
We were creating the S,G upstream state as we should but we were
only looking at the S,G ifchannel to decide the S,G mroute we would
be creating. As such what we need to do is to look over the associated
*,G ifchannels and allow us to associate correct oil needed.
Ticket: CM-24732
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
1. vxlan instance cleanup needs to be done before the upstream entries are
force-flushed.
2. also vxlan callbacks need to be ignored post instance-cleanup.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
This was resulting in static analyzer warnings for subsequent usage
of the same pointer -
pimd/pim_vxlan.c:962:36: warning: Access to field 'info' results in a
dereference of a null pointer (loaded from variable 'ifp')
pim_ifp = (struct pim_interface *)ifp->info;
^~~~~~~~~
1 warning generated.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
The MLAG component on the switch is expected to provide some
properties (such as peerlink-rif) to bootstrap the anycast-VTEP
functionality. The final interface for this is being defined as
a part of the pim-mlag functionality.
This commit provides a hidden command to test the anycast-VTEP
functionality independent of the MLAG component.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Sample output:
root@TORS1:~# vtysh -c "show ip pim vxlan-groups"
Codes: I -> installed
Source Group Input Output Flags
27.0.0.7 239.1.1.101 lo I
* 239.1.1.100 - ipmr-lo I
* 239.1.1.101 - ipmr-lo I
27.0.0.7 239.1.1.100 lo I
root@TORS1:~#
root@TORS1:~# vtysh -c "show ip pim vxlan-work"
Codes: I -> installed
Source Group Input Flags
27.0.0.7 239.1.1.100 lo I
PS: note the worklist dump is a hidden command
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
The unique physical IP is used as the SIP in the ip header to ensure
that pim-register-stop makes it back to the right MLAG switch.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
1. peerlink-rif as OIF in origination mroutes -
Hosts are multi-homed to the anycast-VTEP pair and can send BUM traffic to
either switch. But the RP would have only joined one MLAG switch for
pulling down the MDT. To make that work we add the peerlink/ISL as
an OIF to origination mroutes (TORC11<=>TORC12 is an anycast VTEP pair) -
root@TORC11:~# ip mr |grep "(36.0.0.9, 239.1.1.100)"
(36.0.0.9, 239.1.1.100) Iif: peerlink-3.4094 Oifs: peerlink-3.4094 uplink-1
root@TORC11:~#
root@TORC12:~# ip mr |grep "(36.0.0.9, 239.1.1.100)"
(36.0.0.9, 239.1.1.100) Iif: peerlink-3.4094 Oifs: peerlink-3.4094
root@TORC12:~#
2. VTEP-PIP as register source -
TORC11 and TORC12 share the same anycast VTEP IP (36.0.0.9 in the above
example). And that is the source registered by both VTEPs for all the BUM
mcast-groups. However to allow the pim register start machine to close
the SIP in the register-pkt's IP header must be set to an unique IP address.
This is the VTEP PIP.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
1. special handling of term device in orig mroutes -
The multicast-vxlan termination device ipmr-lo is added to the (*, G)
mroute -
(0.0.0.0, 239.1.1.100) Iif: uplink-1 Oifs: uplink-1 ipmr-lo
This means that it will be inherited into all the SG entries including the
origination mroute. However we cannot terminate the traffic we originate
so some special handling is needed to exclude the termination device
in the origination entries -
27.0.0.7, 239.1.1.100) Iif: lo Oifs: uplink-1
2. special handling of term device on the MLAG pair -
Both MLAG switches pull down BUM-MDT traffic but only one (the DF) can
terminate the traffic. The non-DF must not exclude the termination device
from the MFC to prevent dups to the overlay.
DF -
root@TORC11:~# ip mr |grep "(0.0.0.0, 239.1.1.100)"
(0.0.0.0, 239.1.1.100) Iif: uplink-1 Oifs: uplink-1 ipmr-lo State: resolved
root@TORC11:~#
non-DF -
root@TORC12:~# ip mr |grep "(0.0.0.0, 239.1.1.100)"
(0.0.0.0, 239.1.1.100) Iif: uplink-1 Oifs: uplink-1 State: resolved
root@TORC12:~#
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
An interface needs to be designated as "termination device" and added to
the termination mroute's OIL. This is used by kernel and ASIC backends
to vxlan-decaps matching flows.
The default termination device is expected to have the prefix (start
sub-string) "ipmr-lo". This can be made configurable if needed -
root@TORS1:~# ip -d link show ipmr-lo
28: ipmr-lo: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/ether 12:5a:ae:74:51:a2 brd ff:ff:ff:ff:ff:ff promiscuity 0
dummy addrgenmode eui64
root@TORS1:~# ip mr
This commit includes the changes to enable pim implicitly on the device
and set it up as the vxlan-term device per-pim-instance.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
For vxlan origination mroutes the IIF is pinned to
a. lo for single VTEPs
b. peerlink-rif for anycast VTEPs
This commit includes the changes to react to pim-vifi add/del for these
devices.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
To terminate a multicast VxLAN tunnel entry we setup a mroute with
ipmr-lo in the OIL -
(0.0.0.0, 239.1.1.100) Iif: uplink-1 Oifs: uplink-1 ipmr-lo
This is done by the vxlan component that add ipmr-lo as a local
member to termination SG entries. In addition termination entries
are also subject to MLAG DF election on the anycast VxLAN-AA setup.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Two flags have been introduced per-upstream entry -
1. XXX_MLAG_VXLAN - This indicates that MLAG DF (designated-forwarded)
election is needed on the entry. In the case of pim-evpn this flag is set
for termination (*, G) entries and will be inherited by the (S, G) entries
that are created as a result of SPT switchover on the G.
2. XXX_MLAG_NON_DF - This is set on entries that have lost the
DF election. Such entries are primarily used for blackholing traffic on
one of the MLAG switches. On a hardware accelerated switch this blackholing
happens in the ASIC preventing (non-needed) traffic hitting the CPU.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
For multicast vxlan tunnels we register the local VTEP-IP independent
of the prescence of BUM traffic i.e. we prime the pump. This
is acheived via NULL registers.
VxLAN orig entries with upstream in a PIM_REG_JOIN state are linked to
a work list for periodic NULL register transmission. Once the SPT setup
is complete the upstream-entry moves to a PIM_REG_PRUNE state and is
remved from the VxLAN work list.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
In a PIM MLAG setup (say L11<->L12 is the anycast VTEP pair) the RP
can choose to join either MLAG switch as the anycast VTEP-IP is
present on both. Let's say the RP joins L11.
Hosts are dual connected to L11<->L12 and can send traffic to either
switch. Let's say a host sends broadcast traffic to L12; now L12
must encapsulate and send the traffic toward L11. To do that the
origination-mroute on L12 must include the ISL in its OIL -
(36.0.0.9, 239.1.1.100) Iif: peerlink-3.4094 Oifs: peerlink-3.4094
L11 has a similar mroute -
(36.0.0.9, 239.1.1.100) Iif: peerlink-3.4094 Oifs: peerlink-3.4094 uplink-1
This mroute is used to rx traffic on peerlink-3.4094 and send it out of
uplink-1. Note that this mroute also includes the peerlink-rif in its
OIL. Explicit removal of IIF from OIL is done by the kernel (and other
dataplanes) to prevent traffic looping.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
For every (local-vtep-ip, bum-mcast-grp) registered by evpn an origination
mroute is setup by pimd. The purpose of this mroute is to forward vxlan
encapsulated BUM -
Sample mroute (single VTEP):
(27.0.0.7, 239.1.1.100) Iif: lo Oifs: uplink-1
Sample mroute (anycast VTEP):
(36.0.0.9, 239.1.1.100) Iif: peerlink-3.4094\
Oifs: peerlink-3.4094 uplink-1
This commit is part-1 of orignation mroute setup and includes setup
of upstream entries with vxlan properties.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
pim-vxlan work is maintained in a lists and processing staggered. One
such work is the generation of periodic null registers for the local
VTEP-IP.
This info is instance agnostic and maintained in a global cache.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
This information will come in from a MLAG component. Hidden commands
will also be provided for testing the interface independent of the
separate MLAG component.
PS: It is possible that this cache will be merged with the base
pim-mlag datastructures once they are available.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
pim vxlan component will create upstream entries and OIFs for
multicast VxLAN tunnel origination and termination in single-VTEP
and anycast-VTEP (MLAG) setups.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
pim_vxlan will use this for registering the local-VTEP-IP wth the RP
independent of the presence of BUM traffic.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
ipmr-lo is a dummy netdev with no additional addressing requirements -
root@TORS1:~# ip -d link show ipmr-lo
28: ipmr-lo: <BROADCAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/ether 12:5a:ae:74:51:a2 brd ff:ff:ff:ff:ff:ff promiscuity 0
dummy addrgenmode eui64
root@TORS1:~#
This device is used by pim-vxlan to signify multicast-vxlan-tunnel
termination.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
In an anycast VTEP setup the peerlink-rif (ISL) is added as a OIF to the
tunnel origination mroute. A new OIF protocol, VxLAN, has been added to
allow that functionalty.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Two devices have special significance to multicast VxLAN tunnels -
1. tunnel origination device -
This device is used as the source device to vxlan-encapsulate BUM traffic.
In the case of the default-vrf this is lo. And in the case of non-default
VRF this is vrf-net-device. This patchset is limited to default-VRF
underlay so all subsequent references of origination-dev are to lo. But it
is possible in the future to extend support to non-default VRFs.
Sample origination mroute on single-VTEP:
(27.0.0.7, 239.1.1.100) Iif: lo Oifs: uplink-1
In the case of MLAG we need to mroute traffic form the MLAG-peer so
we force the IIF to the ISL.
Sample origination mroute on MLAG-VTEP:
(36.0.0.9, 239.1.1.100) Iif: peerlink-3.4094 Oifs: peerlink-3.4094 uplink-1
2. tunnel termination device -
This device is used in the OIL to indicate that packets matching the flow
must be vxlan terminated and overlay packets subsequently forward to the
tenants. A special device has been created for this purpose called ipmr-lo.
This is a simple dummy interface from the kernel perspective which has
special siginficance only to pimd which implicitly enabled pim on the
device and adds it to the termination mroutes.
Sample termination mroute:
(0.0.0.0, 239.1.1.100) Iif: uplink-1 Oifs: uplink-1 ipmr-lo
PS: currently we default the termination device name to "ipmr-lo" but in
the future it is possible to provide a config command to set the
termination device.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
PIM VxLAN handling will create two types of upstream entries and
maintain app-specific properties against the entry.
This commit provides the header definitions for that.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
In a VxLAN-AA setup both the anycast VTEPS can send VxLAN encapsulated
traffic. This is despite the fact that the it is not-DR on the IIF
associated with the originating mroute.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
In a MLAG setup both of the VTEPs can rx and reg-encapsulate BUM traffic
toward the RP. To prevent these duplicates we need a mechanism to disable
register encaps on specific mroutes.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
This is specifically needed to allow pim-evpn mroutes in the MLAG setup -
(36.0.0.11, 239.1.1.100) Iif: peerlink.4094 Oifs: uplink-1, peerlink.4094
I could have gone the other way and disabled PIM_ENFORCE_LOOPFREE_MFC but
that opens the door too wide. Relaxing the checks for mlag-specific mroutes
seemed like the safer choice.
This commit provides the infrastructure to relax checks on a per-mroute
basis.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
In the case of vxlan origination entries IIF is set to -
1. lo for single VTEPs
2. MLAG-ISL for VTEPs multihomed via MLAG.
This commit creates the necessary infrastructure by -
1. allowing the IIF to be set statically (without RPF lookup)
2. and by preventing next-hop-tracking registration
PS: Note that I have skipped additional checks in pim_upstream_del
intentionally i.e. an attempt will be made to remove nexthop-tracking
for the upstream entry (with STATIC_IIF) which will fail because of the
up-entry not being in the nh's hash table. Ideally we should maintain
a nh pointer in the up-entry to prevent this unnecessary processing.
In the abscence of that I wanted to avoid spraying STATIC_IIF checks
all over.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
In the case of pim vxlan we create and keep upstream entries alive
in the abscence of traffic. So we need a mechanism to purge entries
abruptly on vxlan SG delete without having to wait for the entry
to age out.
These are again just the infrastructure changes needed for it.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
For vxlan BUM MDTs we prime the pump and register the local-VTEP-ip
as source even before the first BUM packet is rxed. This commit provides
the infrastructure changes needed for that.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
zebra sends (S, G) and (*, G) entries for BUM mcast groups to pimd. This
commit includes the changes to handle the notifications and trigger the
creation of (S, G) base cache in pimd.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
These entries will be used over the subsequent commits for
1. vxlan-tunnel-termination handling - setup MDT to rx VxLAN encapsulated
BUM traffic.
2. vxlan-tunnel-origination handling - register local-vtep-ip as a
multicast source.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Add a bit of code to allow us to look at specified S,G for
the upstream available to us.
If one item is listed we assume Group, if both we assume Source
then Group.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add a bit of code to allow us to look at specified S,G for
the upstreams available to us.
If one item is listed we assume Group, if both we assume Source then
Group.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Replace cli 'debug static' with 'debug pim static', to make
the 'debug static' node available for staticd (eventually).
Signed-off-by: Mark Stapp <mjs@voltanet.io>
The decision for Update_SPTbit(S,G, iif) includes a test
for JoinDesired(S,G) in section 4.2.2. When we were deciding
to update the spt bit we were not taking this into account.
This commit fixes this issue.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we receive a S,G join and the ifchannel is in S,G RPT Prune state,
pim should transition the ifchannel state to JOIN and transition the
pim_upstream state for the S,G stream.
Ticket: CM-24513
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
pim was sending a triggered response on every S,G RPT prune information
read. Suppose we had this in a *,G message:
*,G
S1, G RPT Prune
S2, G RPT Prune
We would send two triggered *,G messages upstream. This leads to over
processing and quickly changing state if S1 or S2 were in different
states.
Modify the code to send just one Triggered *,G upstream after looking
at all S,G state for a *,G.
Ticket: CM-24531
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
On the LHR after we decide that traffic is flowing and
we set the SPT bit for the S,G *and* the incoming IIF
of the S,G is different than the incoming IIF of the *,G
we should immediately send the *,G S,G RPT Prune as
a triggered response instead of waiting for the next
cycle.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Track whether or not we have received an answer from
our query to do nexthop tracking. This allows us to
go straight to doing a synchronous query for our
RPF.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Start the separation of tracking a Destination from the act
of looking it up. The cojoining of these two concepts led
to a bunch of code that had to think about both problems leading
to weird situations and code paths. Simplify the code by making
pim_ecmp_nexthop_search a static function and we only ever
call pim_ecmp_nexthop_lookup when we need to do a RPF().
pim_ecmp_nexthop_lookup will now attempt to find a stored pnc
and if it finds one it will report on the answer from it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When creating new RP information from a `ip pim rp A.B.C.D/M A.B.C.D`
we should determine if we are the RP even if we can or cannot
determine if we have a path to the RP via RPF.
This is because we should determine if we are the RP based upon a
connected ip address match not whether or not we have a path to
the RPF. We would normally think this is not important but
RPF is inherently asynchronous and we can have a state where
we have registered for nht but have not received the actual
path back yet from zebra.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The current reverse logic led to this code construct
if (!pim_nexthop_lookup(...)) {
//Do something successfull
}
This is backwards and will cause logic errors when people
use this code. Fix to use true/false for success/failure.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When a new pim neighbor comes up, we need to go through and
mark nexthops that we have received from zebra for reachability
tracking so we can refigure stuff. If we pass in the new neighbor
we can limit the search to those nexthops out the interface that
the new neighbor has come up.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The pim_resolve_upstream_nh function call is no longer being used
let's remove it from the code base.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Issue: (*,G) mroute uptime is not updated in mroute table,
after deleting and adding the RP
Root cause: When RP gets deleted or becomes not reachable, then
we un-install the entry from the kernel, but still maintains the
entry in the stack. When RP gets re-configured or becomes reachable,
"show ip mroute" shows the uptime, when the channel_oil gets created.
Fix: Introduce a new time mroute_creation in the channel_oil, gets
updated when mroute gets installed in the kernel.
Signed-off-by: Sarita Patra <saritap@vmware.com>
When we delete an interface, we need to set the interface
ifindex to an internal value so that we don't end up in
a state where the re-addition of the same ifindex, due to
a rename operation, causes an infinite loop.
Fixes:#4007
Fix-Suggested-by: Saravanan K
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we are displaying S,G string data we already auto
display the string as (S,G) no need to have ((S,G)).
Cleanup some that were found during log look through.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The pim_rp_check_is_my_ip_address function was checking to see
if we were the actual RP as well as the pim_register code
was doing the same thing. Remove the reduncancy a bit and
just make this function check for that we are the actual receiver
of this data.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The code as written will scan the entirety of all pim upstreams
on a rpf change, this is not necessary because we know that when
we get a nexthop change we already scan the upstreams reliant
on that and do this work. There is no need to do this again a
short time later.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The interface column in pim was limited to 8 or 9 columns
all over the place in pim, fix the code up to allow interface
length to be up to 16 columns.
Ticket: CM-23083
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we are shutting down, delay the zlookup free to as
late as possible since we may need it still
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Suppose we have 2 routers A and B. Both Router A and B have
the same priority of 1000. Router A is the elected DR.
Now suppose B lowers his priority to 1. He still looses the
DR election and we are not sending a hello with the new priority.
Immediately after this A's priority is also lowered to 1, it
looses the election and sends the hello. B receives this hello
and elects A as the DR( since it has the better ip address)
At this point A believes B is the DR, and B believes A is the
DR until such time that the normal hello from B is sent to A,
which if timed correctly can be a significant amount of time).
This code just causes a hello to be sent if the priority is
changed. Now both sides will be able to converge quickly
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When RP gets deleted, find all the (*, G) upstream whose group belongs to
the deleted RP, release the upstream from pnc->upstream_hash in the function
pim_delete_tracked_nexthop().
Signed-off-by: Sarita Patra <saritap@vmware.com>
When a RP gets deleted, find all the (*, G) upstream whose
group belongs to the deleted RP.
case 1: if the group belongs to any other rp, then call
pim_upstream_update() to update the upstream addr and rpf
information.
case 2: If no RP found for the group, then clear the pim
upstream address and rpf information.
Signed-off-by: Sarita Patra <saritap@vmware.com>
When a new RP is configured, find all the (*, G) upstream whose
group belongs to the new RP and then update the upstream structure
with the below fields.
1. De-register for the old RP.
2. Set the upstream address as new RP
3. Register for the new RP.
4. Update the upstream rpf information and kernel multicast forwarding
cache(MFC), if the new RP is reachable.
Signed-off-by: Sarita Patra <saritap@vmware.com>
When route to RP gets modified, FRR receives a notification from
zebra, and call the function pim_resolve_upstream_nh() to compute the
nexthop and update upstream->rpf structure.
Issue: In case when RP becomes not reachable, FRR only uninstall
the mroute from the kernal, but not update the upstream->rpf structure.
Fix: When FRR receives a notification from zebra saying RP becomes
not reachable, then update the following fields.
1. update channel_oil incoming interface as MAXVIFS
2. Un-install the mroute from the kernel.
3. Switch upstream state from JOINED to NOTJOINED.
4. Clear the nexthop information of the upstream.
Signed-off-by: Sarita Patra <saritap@vmware.com>
When route to RP gets modified, FRR receives a notification from
zebra, and call the function pim_update_rp_nh() to compute the
new nexthop and will update the source_nexthop information of
rp_info. This is not working for the case when RP becomes not
reachable.
Fix: When FRR receives a notification from zebra saying RP becomes
not reachable, then delete the source_nexthop informatio of rp_info.
Signed-off-by: Sarita Patra <saritap@vmware.com>
In this commit, we are creating a dummy upstream & dummy channel_oil
for (*, G) when RP is not configured or not reachable.
Dummy upstream: <upstream_addr = INADDR_ANY, rpf = Unknown>
Dummy channel oil: <iif = MAXVIFS>
Signed-off-by: Sarita Patra <saritap@vmware.com>
When FRR receives IGMP/PIM (*, G) join and RP is not configured or not
reachable, then we are creating a dummy upstream with incoming interface
as NULL and upstream address as INADDR_ANY.
Added upstream address and incoming interface validation where it is necessary,
before doing any operation on the upstream.
Signed-off-by: Sarita Patra <saritap@vmware.com>
When FRR receives IGMP/PIM (*, G) join and RP is not configured or
not reachable, then we are creating a dummy upstream with incoming
interface as NULL.
Added some null checks for the incoming interface, while displaying
the pim upstream information in the cli command "show ip pim upstream".
Signed-off-by: Sarita Patra <saritap@vmware.com>
Added comments which explains the new values for existing fields
and new fields in the upstream and channel_oil data structure.
Following are the summary of the behaviour change in PIM code.
Scenario 1 : RP doesn’t exist/RP not reachable
Event: Join received
Current behaviour:
No upstream gets created
Changed behaviour:
Upstream data structure created with below info
upstream_addr: INADDR_ANY
channel_oil iif: MAXVIF
channel_oil is_valid: FALSE (flag introduced to indicate if this entry is valid to get installed in hardware)
RPF details: Not valid
Join state: NOT_JOINED
Kernal installed: FALSE
Scenario 2: Dummy upstream exists
Event: RP configured
Current Behaviour:
upstream address updated for the dummy upstream created.
Changed Behaviour:
upstream_addr: RP address
channel_oil iif: MAXVIF
channel_oil is_valid: FALSE
RPF details: only RP address updated
Join state: NOT_JOINED
Kernel installed: FALSE
Scenario 3: Dummy upstream exists
Event: RP becomes reachable
Current Behaviour:
Update channel oil, rpf details in the upstream and install in hardware
Changed Behaviour:
upstream_addr: RP Adress
channel_oil iif: MAXVIF
channel_oil is_valid: FALSE
RPF details: RPF details updated via NHT callback
Join state: JOINED
Kernel installed: TRUE
Scenario 4: MRoute exists
Event: RP gets deleted
Current behaviour:
Nothing got updated in him upstream and channel oil,
join timer still runs. Mroute still exists in kernel.
Changed behaviour:
upstream_addr: INADDR_ANY
channel_oil iif: MAXVIF
channel_oil is_valid: FALSE
RPF details: Not valid
Join state: NOT_JOINED (also sent prune towards deleted RPF nbr)
Kernel installed: FALSE
Scenario 5: MRoute Exists
Event: RP unreachable
Current behaviour:
Nothing got updated in him upstream and channel oil,
join timer still runs. Mroute sdeleted from kernel.
Changed behaviour:
upstream_addr: RP address
channel_oil iif: MAXVIF
channel_oil is_valid: FALSE
RPF details: only RP address updated
Join state: NOT_JOINED (also sent prune towards deleted RPF nbr)
Kernel installed: FALSE
Scenario 6: Mroute exists
Event: Better RP configured with precise group range & reachable.
Current behaviour:
No effect on existing route.
Changed behaviour:
Upstream address: Better RP
RPF interface: towards the better RP
Join state: JOINED (Send a prune towards the old RP and send a join
towards the better RP)
Scenario 7: Mroute exists
Event: RP deleted and another RP with broad group range fits this group & reachable
Current behaviour:
No effect on current behaviour
Changed behaviour:
Upstream address: next available RP
RPF interface: towards the next available RP
Join state: JOINED (Send a prune towards the old RP and send a join
towards the better RP)
Signed-off-by: Sarita Patra <saritap@vmware.com>
Add a test command to pim that allows you to reset the keepalive timer
for an upstream to it's max value. This is to allow purposeful testing
of cleanup code in pim, by forcing the keeaplive timer to expire later.
robot# show ip pim upstream
Iif Source Group State Uptime JoinTimer RSTimer KATimer RefCnt
enp3s0 192.168.201.136 225.1.0.0 NotJ,RegP 00:00:10 00:00:52 00:00:25 00:02:54 1
robot# show ip pim upstream
Iif Source Group State Uptime JoinTimer RSTimer KATimer RefCnt
enp3s0 192.168.201.136 225.1.0.0 NotJ,RegP 00:00:11 00:00:51 00:00:24 00:02:53 1
robot# test pim keep 192.168.201.136 225.1.0.0
Setting (192.168.201.136,225.1.0.0) to current keep alive time: 210
robot# show ip pim upstream
Iif Source Group State Uptime JoinTimer RSTimer KATimer RefCnt
enp3s0 192.168.201.136 225.1.0.0 NotJ,RegP 00:00:27 00:00:35 00:00:08 00:03:27 1
robot#
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Issue: Configure "ip pim rp x.x.x.x 225.0.0.0/4".
Show running config shows "ip pim rp x.x.x.x 224.0.0.0/4"
This is mis-leading.
Root-cause: Internally 225.0.0.0/4 is getting converted to
224.0.0.0/4 group mask, since the prefix length is 4.
Fix: Restrict the user to configure inconsistent group address
mask by throughing a cli error "Inconsistent address and mask".
Signed-off-by: Sarita Patra <saritap@vmware.com>
Issue: Shut the RP interface in the router RP. LHR will get to know
RP becomes not-reachable, so it send a prune towards the RP. On
receiving the prune, RP clear the (*, G) entry, but (S, G) should
not get removed if present.
Now no-shut the RP interface in the router RP. LHR will send a (*, G)
join towards the RP. On receiving join FRR create the (*, G) entry.
Along with this, it also add the interface(join received) in the OIL
of (S, G) and also refresh the (S, G) timer.
Fix: Dont refresh the timer for S, G or (*, G), if the flag for the
channel OIL is PIM_OIF_FLAG_PROTO_ANY.
Signed-off-by: Sarita Patra <saritap@vmware.com>
Add a command to track if an interface should be in active-active
mode or not. This command is hidden at this time because it
is not finished fully.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
- some target_CFLAGS that needed to include AM_CFLAGS didn't do so
- libyang/sysrepo/sqlite3/confd CFLAGS + LIBS weren't used at all
- consistently use $(FOO_CFLAGS) instead of @FOO_CFLAGS@
- 2 dependencies were missing for clippy
Signed-off-by: David Lamparter <equinox@diac24.net>
If you have an interface being added to a static mroute
and that interface has been configured w/ pim but does
not have a valid ip address yet, we do not create a
VIF for that device yet. As such when we attempt
to assign the vif array in the pim static data structure
we attempt to write into -1 of that array.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The pimg data structure is only used in one spot to send the default
vrf id to zebra upon startup. Add the default vrf id to the struct pim_router
data structure and remove the pimg pointer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Create a `struct pim_router` and move the thread master into it.
Future commits will further move global varaibles into the pim_router
structure.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Just add the ability to notice the capabilities on startup,
but don't do anything with it yet.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we receive a igmp report and attempt to initiate
a pim ifchannel for it and that fails to work then
let's back out the work done setting stuff up to this
point.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we fail to add a local membership add some additional debugs
so that we can have a bit more information on when something goes
bad.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
It's been a year since we added the new optional parameters
to instantiation. Let's switch over to the new name.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When sending a sockoption for MRT_INIT, *bsd requires that
the data passed in must be 1. While linux does not, the
code was sending in a positive value that was causing issues
on *bsd of protocol not supported.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When trying to run PIM on *bsd, the kernel expects to only
allow the pim kernel socket to work if we elevate priviledges.
So do so.
This commit gets us further in the startup of PIM on *bsd
but is not sufficient to get it fully started yet.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Introduce frr-interface.yang, which defines a model for managing FRR
interfaces.
Update the 'frr_yang_module_info' array of all daemons that will
implement this module.
Add automatically generated stub callbacks in if.c. These callbacks will
be implemented in the following commit.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
FRR_DAEMON_INFO should now contain an array of 'frr_yang_module_info'
structures describing the YANG modules implemented by the daemon.
This array will be used by frr_init() function to load all YANG modules
and initialize the northbound callbacks during the daemon initialization.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Resolves issue with exit-vrf being placed at the end of zebra's portion
of a vrf block, but before other daemons' portions of the same config
block.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
The ->hash_cmp and linked list ->cmp functions were sometimes
being used interchangeably and this really is not a good
thing. So let's modify the hash_cmp function pointer to return
a boolean and convert everything to use the new syntax.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This commit fixes two issues during pim shutdown.
1) The rp_info structure was being freed before the
outgoing notifications that depended on it's information
was sent out as part of shutdown.
2) The pim->upstream_list shutdown involved iterating
over the list via ALL_LIST_ELEMENTS. This typically
is enough but pim will auto delete child nodes as well
as itself when it goes away and they depend on it. As such
the node and nnode could possibly already have been freed.
So change the way we look at all the data in the upstream_list
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Suppose we have a bridge with a host and two routers attached
to it.
r1 r2
| |
--------
|
host
host is sending traffic.
r1 and r2 are pim neighbors and r2 is the DR.
Both r1 and r2 will receive data from the stream up the pim
kernel socket. r1 will notice that it is not the DR and
stop processing in pim. This code adds a bit more code to blackhole
the route when r1 detects it is not the DR in this scenario.
This is being done because the kernel is both keeping state and
sending data to the pim process to continue processing this.
Additionally if we happen to be running this on a asic, then
blackholing the route in the asic can save a significant amount
of cpu time handling this situation.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we decide we are not the right pim process to add upstream state
for the igmp state received, notice this in a debug to make life
easier to debug.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The tracking of who have drpriority on an interface
in pim was not displayed anywhere. Add to the show
command for future reference.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In pim_if_new use bool instead of an int to pass
true/false values for what we should create the
pim interface type for.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The startup of a non-integrated config was not properly
allowing for startup to create the vif when we have
not learned about the interface we are trying to configure
at this point in time. Actually notice when we are
trying to create a pimreg device or not to properly
notice when to attempt to create the vif or not.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow at timer wheel creation time the ability to specify a
name for what we want the 'show thread cpu' to show up as.
Modify pim to note this.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
A new command "ip pim" is created to configure pim sm on an
interface, which replaces the existing commands "ip pim sm"
and "ip pim ssm" and make "ip pim sm" and "ip pim ssm" as
hidden commands. The command "ip multicast-routing" is removed
since it is already enabled on FRR by default.
Signed-off-by: Sarita Patra saritap@vmware.com
config.h (or, transitively, zebra.h) must be the first include file
listed for autoconf things like _GNU_SOURCE and _POSIX_C_SOURCE to work
correctly.
Signed-off-by: David Lamparter <equinox@diac24.net>
Since we're now building through one large Makefile, we can easily put
things with their daemons and crossreference nicely.
Signed-off-by: David Lamparter <equinox@diac24.net>
Problem reported that some bgp and ospf json commands did not return
any json output at all if the bgp/ospf instance did not exist.
Additionally, some bgp and ospf json commands did not return any json
output if the instance existed but no neighbors were defined. This
fix makes these commands more consistent in returning empty braces for
json output and issue a message if not using json output. Additionally,
made the flag "use_json" a bool to make it consistent since previously,
it had been defined as an int, char, u_char, and bool at various places.
Ticket: CM-21040
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
The Vrf aliases can be known with a specific hook. That hook will then,
from zebra propagate the information to the relevant zapi clients.
The registration hook function is the same for all daemons.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
End user was seeing this debug but we are not giving
the user enough information to debug this on his own.
Add a tiny bit of extra information that could point
the user to solving the problem for themselves.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When pimd is getting terminated, pim_upstream_del() gets called as
part of cleaning process. pim_upstream_del() deletes the route and
assigns NULL to the up->channel_oil. It also deletes each if_channel
by calling the function pim_ifchannel_delete().
pim_ifchannel_delete() internally calls the caller function pim_upstream_del(),
if it is the last ifchannel for that upstream. So pim_upstream_del
is getting called twice, which will access the up->channel_oil which
was already set to NULL before. This results in crash.
Fix:
pim_ifchannel_delete() should call pim_upstream_del (caller function)
only if the up->ref_count > 0. Added an assert(up->ref_count > 0) in
the function pim_upstream_del().
Signed-off-by: Sarita Patra <saritap@vmware.com>
e.g.
pimd/pim_oil.c: In function ‘pim_channel_oil_dump’:
pimd/pim_oil.c:51:19: error: ‘%d’ directive writing between 1 and 11 bytes into a region of size 10 [-Werror=format-overflow=]
Build on gcc-8.2.0 is warning-free after this patch.
Signed-off-by: David Lamparter <equinox@diac24.net>
