Zebra is starting to have some run-time capabilites that would be
useful to pass up to the higher level protocols so that they
can act in an appropriate manner when needed.
Send the ecmp value zebra is being run with and whether or not
we believe mpls is enabled in the kernel or not.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In order to avoid duplicates functions, the zebra_pbr_rule structure
used by zebra to decode the zapi message, and send netlink messages, is
slightly modified. the structure is derived from pbr_rule, but it also
includes sock identifier that is used to send back information to the
daemon that did the request. Also, the ifp pointer is stored in that
structure.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Those messages permit a remote daemon to configure an iptable entry. A
structure is defined that maps to an iptable entry. More specifically,
this structure proposes to associate fwmark, and a table ID.
Adding to the configuration, the initialisation of iptables hash list is
done into zebra netnamespace. Also a hook for notifying the sender that
the iptables has been correctly set is done.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
PBR rule is being added a 32 bit value that can be used to record a rule
in the kernel, by using a fwmark information.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Once ipset entries are injected in the kernel, the relevant daemon is
informed with a zebra message sent back.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
ZEBRA IPSET defines are added for creating/deleting ipset contexts.
Ans also create ipset hash sets.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The header length needs to be subtracted from the handling
side of the zapi in zebra. This is because we refigure the
header data structure. The receive side doesn't care
about the total header length so no need to subtract there.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In BGP, doing policy-routing requires to use table identifiers.
Flowspec protocol will need to have that. 1 API from bgp zebra has been
done to get the table chunk.
Internally, onec flowspec is enabled, the BGP engine will try to
connect smoothly to the table manager. If zebra is not connected, it
will try to connect 10 seconds later. If zebra is connected, and it is
success, then a polling mechanism each 60 seconds is put in place. All
the internal mechanism has no impact on the BGP process.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This commit is connecting the table manager with remote daemons by
handling the queries.
As the function is similar in many points with label allocator, a
function has been renamed.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The following types are nonstandard:
- u_char
- u_short
- u_int
- u_long
- u_int8_t
- u_int16_t
- u_int32_t
Replace them with the C99 standard types:
- uint8_t
- unsigned short
- unsigned int
- unsigned long
- uint8_t
- uint16_t
- uint32_t
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
When a route_delete is received allow the deletion
to occur in the passed in tableid if the vrf is VRF_DEFAULT.
This now matches route_add behavior in rib_add_multipath
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ensure that we have properly decoded the zapi_route sent to us
and if we cannot decode, log and move on.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When figuring out whom to call and if we actually can legally
call into the handler array actually use the number of elements
in the array instead of the size of the array.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When zebra detects that the originator has dissapeared
delete all rules associated with that client.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
There were several places where when I am attempting
to debug zebra functionality that I would really
like to have the ability to know what vrf I think
I am operating on.
Add the vrf_id to a bunch of zlog_debug messages
to help figure out issues when they happen.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Group send and receive functions together, change handlers to take a
message instead of looking at ->ibuf and ->obuf, allow zebra to read
multiple packets off the wire at a time.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
A lot of the handler functions that are called directly from the ZAPI
input processing code take different argument sets where they don't need
to. These functions are called from only one place and all have the same
fundamental information available to them to do their work. There is no
need to specialize what information is passed to them; it is cleaner and
easier to understand when they all accept the same base set of
information and extract what they need inline.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Formalize the ZAPI header by documenting it in code and providing it to
message handlers free of charge to reduce complexity.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
All of the ZAPI message handlers return an integer that means different
things to each of them, but nobody ever reads these integers, so this is
technical debt that we can just eliminate outright.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Every place we need to pass around the rule structure
we need to pass around the ifp as well. Move it into
the structure. This will also allow us to notify up
to higher level protocols that this worked properly
or not better too.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Keep track of rules written into the kernel. This will
allow us to delete them on shutdown if we are not cleaned
up properly.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow the add/delete to go through a intermediary function in
zebra_pbr.c instead of directly to the underlying os call. This
will allow future refinements to track the data a bit better
so that on shutdown we can delete the rules.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
1) use uint32_t instead of u_int32_t as we are supposed to
2) Consolidate priority into the rule.
3) Cleanup the api from this.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Also modify `struct route_entry` to use nexthop_groups.
Move ALL_NEXTHOPS loop to nexthop_group.h
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow the calling daemon to pass down what table-id we
want to use to install the route. Useful for PBR.
The vrf id passed must be the VRF_DEFAULT else this
value is ignored.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When decoding and creating the appropriate data structures
for a nexthop, use the passed in vrf.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Implement support for EVPN symmetric routing for IPv6 routes. The next hop
for EVPN routes is the IP address of the remote VTEP which is only an IPv4
address. This means that for IPv6 symmetric routing, there will be IPv6
destinations with IPv4 next hops. To make this work, the IPv4 next hops are
converted into IPv4-mapped IPv6 addresses.
As part of support, ensure that "L3" route-targets are not announced with
IPv6 link-local addresses so that they won't be installed in the routing
table.
Signed-off-by: Vivek Venkatraman vivek@cumulusnetworks.com
Reviewed-by: Mitesh Kanjariya mitesh@cumulusnetworks.com
Reviewed-by: Donald Sharp sharpd@cumulusnetworks.com
The addition of the name of the netns in the vrf message introduces also
a limitation when the size of the netns is bigger than 15 bytes. Then
the netns are ignored by the library.
In addition to this, some sanity checks have been introduced. some
functions to create the netns from a call not coming from the vty is
being added with traces.
Also, the ns vty function is reentrant, if the context is already
created.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Add a bit more detail to tell us what we are sending
up to a protocol so we can debug it better in the
future.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If you were to configure a v4 and v6 vrf pop and forward label
that both happened to be the same, unconfiguring one would
remove them both.
This fixes that issue by noticing if we should remove it or
not based upon v4 or v6 having the same label or not.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add the ability to pass in an afi to zebra. zebra_vrf keeps
track of the afi/label tuple and then does the right thing
before we call down. AF_MPLS does not care about v4 or v6
it just knows label and what device to use for lookup.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
