Ticket: CM-6690
Reviewed By: Donald, Kanna
Testing Done:
Double commit of 4bbc0cf4a98d7fd2aabe47241424fa7c5a3ae1eb from br2.5 to master
PTM cable status updates were not being handled in the notification callback registered with the ptm lib. This results in interface ptm status mismatch between PTM and zebra when interface cable check status changes (pass->fail or fail->pass). Zebra requests PTM to send cable status updates using get-status command and PTM sends the cable status updates as command responses to get-status. This was being handled in the commmand response callback registered with ptm lib. But, the subsequent status updates come as notifications and handling of those notifications that was missing in the notification callback. Fixed the issue by making a common callback for command responses and notifications. All the command responses other than the responses to get-status are dropped/ignored.
Integrates Prescriptive Topology Module(ptm) into quagga.
If this module is enabled, link ups are notified only after the link is verified
as being connected to the neighbor specified. The neighbor specification and
checking is done by the ptm daemon.
<This is a recommit of this patch because it was changed in situ>
OSPF BFD command enhancement to configure BFD parameters (detect multiplier, min rx and min tx).
interface <if-name>
ip ospf bfd <detect mult> <min rx> <min tx>
This patch also adds BFD support for IPv6 OSPF. ospf6d will dynamically register/deregister IPv6 neighbors with BFD for monitoring the connectivity of the neighbor. Neighbor is registered with BFD when 2-way adjacency is established and deregistered when adjacency goes down if the BFD is enabled on the interface through which the neighbor was discovered.
OSPF6 BFD command added to configure BFD and parameters (detect multiplier, min rx and min tx).
interface <if-name>
ipv6 ospf6 bfd <detect mult> <min rx> <min tx>
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
This patch also adds BFD multihop support for BGP. Whether a peer is multi-hop or single hop is determined internally. All IGP peers are considered as multi-hop peers. EBGP peers are considered as single hop unless configured as multi-hop.
BGP BFD command enhancement to configure BFD parameters (detect multiplier, min rx and min tx).
router bgp <as-number>
neighbor <name/ip-address> bfd <detect mult> <min rx> <min tx>
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
protocols. BGP and OSPF are integrated to respond this BFD session down message
originated in Zebra via ptmd.
BGP and OSPF now have a bfd command, which tells OSPF/BGP to respond to the
BFD session down message.
OSPF:
interface <>
ip ospf bfd
BGP:
router bgp <>
neighbor <> bfd
Please note that these commands don't enable BFD as a protocol. BFD configuration
and paramter tuning are via BFD applicable UI.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Integrates Prescriptive Topology Module(ptm) into quagga.
If this module is enabled, link ups are notified only after the link is verified
as being connected to the neighbor specified. The neighbor specification and
checking is done by the ptm daemon.
