This function is sure to return correct value by "assert", so the
checking its return value should be removed.
Signed-off-by: anlan_cs <anlan_cs@tom.com>
Add optional NHG ID output to `show ip route` dumps. We have
this in json output already as nexthopGroupID but nice
to have the option in a normal dump as well. Not including in main
output for now to avoid breaking screen scrapers.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
On startup we create a thread timer event to do a rib sweep
of the system. On shutdown we never stopped this timer and
as such we have a situation where a thread event could be run
on shutdown after the data for it has been freed. Here is the
crash I am seeing:
(gdb) bt
(gdb)
Save the thread data in zebra_router and stop the thread so we don't
accidently do work on shutdown we don't mean to. In this case
it happened in our topotests with some severe system load.
Essentially we happened to kill the zebra daemon just as the
graceful_restart timer popped here.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
In some cases, zebra may install a nexthop-group id that is
different from the id of the nhe struct attached to a
route-entry. This happens for a singleton recursive nexthop,
for example, where a route is installed with the resolving
nexthop's id.
The installed value is the most useful value - that corresponds
to information in the kernel on linux/netlink platforms that
support nhgs. Display both values if they differ in ascii
output, and include both values in the json form.
Signed-off-by: Mark Stapp <mstapp@nvidia.com>
Since f60a1188 we store a pointer to the VRF in the interface structure.
There's no need anymore to store a separate vrf_id field.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
During zebra shutdown, we clear out the LSP workqueue. The LSPs
will be uninstalled and freed during the shutdown process, so
just ignore any LSPs that happen to be on the workqueue.
Signed-off-by: Mark Stapp <mstapp@nvidia.com>
At some scale we eventually run out of room displaying v4/v6 route
totals for `show zebra client summ`:
janelle# show zebra client summ
Name Connect Time Last Read Last Write IPv4 Routes IPv6 Routes
--------------------------------------------------------------------------------
bgp 04w0d18h 00:00:19 00:01:2411729127/4052681 2037786/903094
This total over ran the space in just a little over a week of uptime.
Expand to have a bit more room.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The dplane_ctx_get_pbr_ipset_entry function only
failed when the caller did not pass in a valid
usable pointer. Change the code to assert on
a pointer not being passed in and remove the
bool return
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The only time this function ever failed is when
the developer does not pass in a usable pointer
to place the data in. Change it to an assert
to signify to the end developer that is what
we want and then remove all the if checks
for failure
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The function call dplane_ctx_get_pbr_ipset only
returns false when the calling function fails to
pass in a valid ipset pointer. This should
be an assertion issue since it's a programming
issue as opposed to an actual run time issue.
Change the function call parameter to not return
a bool on success/fail for a compile time decision.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
We should always treat the VRF interface as a loopback. Currently, this
is not the case, because in some old pre-VRF code we use if_is_loopback
instead of if_is_loopback_or_vrf. To avoid any future problems, the
proposal is to rename if_is_loopback_or_vrf to if_is_loopback and use it
everywhere. if_is_loopback is renamed to if_is_loopback_exact in case
it's ever needed, but currently it's not used anywhere.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
During shutdown, when table_manager_disable is called for the default
VRF, its vrf_id is already set to VRF_UNKNOWN, so the expression is true
and the table manager memory is not freed. Change the expression to
compare the VRF name instead of the id. The check in table_manager_enable
is changed for consistency.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Free the LSP workqueue later during shutdown, so that zebra
has enough time to clean up and uninstall any LSPs.
Signed-off-by: Mark Stapp <mstapp@nvidia.com>
42d4b30e introduced per-VRF table manager.
Table manager is allocated when the VRF is created, but it is freed when
the VRF is disabled. When this VRF is re-enabled, zebra ends up with
table manager being NULL pointer and it crashes on any dereference.
Table manager should be freed when the VRF is deleted, not when it's
disabled.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
We don't receive interface down/delete notifications from kernel when a
netns is deleted. Therefore we have to manually replicate the necessary
actions, otherwise interfaces are kept in the system with stale pointers
to the deleted netns.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Problem:
L2-VNI SVI down followed by L2-VNI's vxlan device
deletion leads to stale entry into L3VNI's
L2-VNI list.
Solution:
When L2-VNI associated SVI is down, default vrf
is the new tenant vrf.
Remove L2-VNI from L3VNI's l2vni list as
L3VNI/VRF is no longer valid in absence of associated
SVI.
When SVI is up re-add L2-VNI into associated VRF's
L3VNI.
The above remove/add from the L3VNI's L2VNI list is
already done when vxlan or L2-VNI is flaped, just need
to handle when SVI is flapped.
Ticket:#2817127
Reviewed By:
Testing Done:
After deleting SVI following by L2-VNI deletion,
L3VNI's L2-VNI list delets the L2-VNI. (no stale entry).
After adding back SVI/L2-VNI, L3VNI list adds back the
L2-VNI and it is associated right tenant VRF.
Signed-off-by: Chirag Shah <chirag@nvidia.com>
