The RPF cost is incremented by 10 if the RPF interface is the peerlink-rif.
This is used to force the MLAG switch with the lowest cost to the RPF
to become the MLAG DF. If a switch has to go via the peerlink-rif to get
to the RP or source it simplly cannot be the designated forwarder.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
DF election is only run for (*,G) entries i.e. election is skipped
for (S,G) entries that are setup as a result of SPT switchover. (S,G)
entries inherit the DF role from the parent (*,G) entry. So the DF is
responsible for terminating all sources associated with a group.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
1. Upstream entries associated with tunnel termination mroutes are
synced to the MLAG peer via the local MLAG daemon.
2. These entries are installed in the peer switch (via an upstream
ref flag).
3. DF (Designated Forwarder) election is run per-upstream entry by both
the MLAG switches -
a. The switch with the lowest RPF cost is the DF winner
b. If both switches have the same RPF cost the MLAG role is
used as a tie breaker with the MLAG primary becoming the DF
winner.
4. The DF winner terminates the multicast traffic by adding the tunnel
termination device to the OIL. The non-DF suppresses the termination
device from the OIL.
Note: Before the PIM-MLAG interface was available hidden config was
used to test the EVPN-PIM functionality with MLAG. I have removed the
code to persist that config to avoid confusion. The hidden commands are
still available.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Channel with the MLAG daemon is setup on the first VxLAN BUM MDT or
pim-mlag AA SVI.
This channel is used for -
1. rxing MLAG status status updates (peer state, role etc.)
2. for syncing active-active upstream entries with the peer MLAG
switch.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
RFC 4861 states that ipv6 RA messages sent out an interface should
contain all global ipv6 addresses on that interface. This fix adds
that capability. To override the default flags and timer settings
for a particular prefix, the existing "ipv6 nd prefix ..." command
should be used via vtysh under the appropriate interface.
Ticket: CM-20363
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Add some additional output/debug to code to allow
us to see the vrf name instead of just the vrf id.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add a quick macro to allow for safe dereference of the vrf
since it may or may not exist in all cases.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The babel_main_loop function did not have a return for
a non-void function. For some reason gcc is starting to complain
about this now.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Override ORIGIN attribute if defined.
E.g.: Cisco and Juniper set ORIGIN for aggregated address
to IGP which is not what rfc4271 says.
This enables the same behavior, optionally.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Track the returned peer_sorted value and use it where
we can and recalculate where necessary.
This is an effort to reduce the amount of work done here.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The act of peer_sort() being called always set this value
even when we are just looking it up. We need to seperate
out the idea of lookup from set.
For those places that this is immediately obvious that
this is a lookup switch over to using this function.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
A route where ESI, GW IP, MAC and Label are all zero at the same time SHOULD
be treat-as-withdraw.
Invalid MAC addresses are broadcast or multicast MAC addresses. The route
MUST be treat-as-withdraw in case of an invalid MAC address.
As FRR support Ethernet NVO Tunnels only.
Route will be withdrawn when ESI, GW IP and MAC are zero or Invalid MAC
Test cases:
1) ET-5 route with valid RMAC extended community
2) ET-5 route no RMAC extended community
3) ET-5 route with Multicast MAC in RMAC extended community
4) ET-5 route with Broadcast MAC in RMAC extended community
Signed-off-by: Kishore Aramalla <karamalla@vmware.com>
Current failed reasons for bgp when you have a peer that
is not online yet is `Waiting for NHT`, even if NHT has
succeeded. Add some code to differentiate this.
eva# show bgp ipv4 uni summ failed
BGP router identifier 192.168.201.135, local AS number 3923 vrf-id 0
BGP table version 0
RIB entries 0, using 0 bytes of memory
Peers 2, using 43 KiB of memory
Neighbor EstdCnt DropCnt ResetTime Reason
192.168.44.1 0 0 never Waiting for NHT
192.168.201.139 0 0 never Waiting for Open to Succeed
Total number of neighbors 2
eva#
eva# show bgp nexthop
Current BGP nexthop cache:
192.168.44.1 invalid, peer 192.168.44.1
Must be Connected
Last update: Mon Feb 10 19:05:19 2020
192.168.201.139 valid [IGP metric 0], #paths 0, peer 192.168.201.139
So 192.168.201.139 is a peer for a connected route that has not been
created on .139, while 44.1 nexthop tracking has not succeeded yet.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
