This was the intent here to begin with, not sure where I managed to
forget this along the way...
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The timestamps used for the live log are wallclock, not monotonic. Also
some fields were left uninitialized.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Commit: ea47320b1d
Modified the bgp_clear_stale_route function to have
better indentation, but in the process changed some
`continue;` statements to `break;` which modified
the looping and caused stale paths to not always be
removed upon an update.
To reproduce: A ---- B, setup with addpath and GR
One side has a prefix with nhop1 and nhop2, kill one
side and then resend the same prefix with nhop3,
paths nhop1 and 2 become stale and never removed.
Code inspection clearly shows that that `continue`
statements became `break` statements causing the
loop over all paths to stop prematurely.
The fix is to change the break back to continue
statements so the loop can continue instead of
stopping.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
While running singlethreaded, the RCU code is "dormant" and rcu_free is
an immediate operation. This results in the log target loop accessing
free'd memory if a log target removes itself while a message is printed
(which is likely to happen on e.g. error conditions.)
Just use frr_each_safe to avoid this issue.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
- rather than coerce `const char *` to std:string&, just pass the
C ptr, as that's what is used anyway.
fixes#10578
Signed-off-by: Christian Hopps <chopps@labn.net>
Don't let open sockets hang for too long. This will fix an issue where a
improperly coded client (e.g. socat) could exaust the amount of open
file descriptors.
Documentation:
https://grpc.github.io/grpc/cpp/md_doc_keepalive.html
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
In the loop, local variable `ip` is always set even if the check condition
is not satisfied.
Avoid the redundant set, move this set exactly after the check condition is
satisfied. Set `ip` only if the check condition is met, otherwise needn't.
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Bad formatting applied and it worked with small amount of prefixes (lurking).
With full BGP feed and full RPKI table, this causes infinity loop.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
This issue is applicable to other protocols as well.
When user has used route-map, even though the prefixes are falling
under the permit rule, the prefixes were denied and were shown
as inactive route in zebra.
Reason being the parameter which is of type enum was passed to the api
route_map_get_index and was typecasted to uint8_t *.
This problem is visible in case of Big Endian systems because we are
accessing the most significant byte.
'match_ret' field is an enum in the caller and so it is of 4 bytes,
the typecasting it to 1 byte and passing it to the api made
the api to put the value in the most significant byte
which was already zero previously. Therefore the actual value
RMAP_NOMATCH which was 1 never gets reset in this case.
Therefore the api always returns 'RMAP_NOMATCH' and hence
the prefixes are always denied.
Fixes: #9782
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
zebra crash is seen during shutdown (frr restart).
During shutdown, remote neigh and remote mac clean up
is triggered first, followed by per vni all neigh
(including local) and macs cleanup is triggered.
The crash occurs when a remote mac is cleaned up first
and its reference is remained in local neigh.
When local neigh attempt removes itself from its associated
mac's neigh_list it triggers inaccessible memory crash.
The fix is during mac deletion if its neigh_list is non-empty
then retain the MAC in AUTO state.
This can arise when MAC and neigh duo are in different state
(remote/local). Otherwise, the order of cleanup operation
is neighs followed by macs.
The auto mac will be cleaned up when per vni all neighs and macs
are cleaned up.
Ticket:CM-29826
Reviewed By:CCR-10369
Testing Done:
Configure evpn symmetric config where
MAC is in remote state and neigh is in local state.
Perform frr restart then crash is not seen.
Signed-off-by: Chirag Shah <chirag@nvidia.com>
With recent changes to interface up mechanics in if_netlink.c
FRR was receiving as many as 4 up events for an interface
on ifdown/ifup events. This was causing timing issues
in FRR based upon some fun timings. Remove this from
happening.
Ticket: CM-31623
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Vxlan interfaces flap (protodown/up) event,
non ptm operative interfaces do not come up
as protodown up event do not trigger "if_up()"
event.
Ticket:CM-30477
Reviewed By:CCR-10681
Testing Done:
validated interfaces flaps, ip link down, ifdown
and protodown followed by UP event. all Vxlan interfaces
come up in bgpd post flap.
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Frr need to handle protocol down event for vxlan
interface.
In MLAG scenario, one of the pair switch can put
vxlan port to protodown state, followed by
tunnel-ip change from anycast IP to individual IP.
In absence of protodown handling, evpn end up
advertising locally learn EVPN (MAC-IP) routes
with individual IP as nexthop.
This leads an issue of overwriting locally learn
entries as remote on MLAG pair.
Ticket:CM-24545
Reviewed By:CCR-10310
Testing Done:
In EVPN deployment, restart one of the MLAG
daemon, which puts vxlan interfaces in protodown state.
FRR treats protodown as oper down for vxlan interfaces.
VNI down cleans up/withdraws locally learn routes.
Followed by vxlan device UP event, re-advertise
locally learn routes.
Signed-off-by: Chirag Shah <chirag@nvidia.com>
We can use PIMADDR_ANY instead of INADDR_NONE to initalize rp->rpf_addr
when there is no rp configured for group_all.
Signed-off-by: sarita patra <saritap@vmware.com>
