When sending BMP messages for a status change event for a peer whose NHT
has failed, we were sending a Peer Down Reason Code of 1 (Local system
closed, NOTIFICATION follows) with no NOTIFICAION PDU (because there was
none). This is wrong. Also, the reason code of 1 is semantically off, it
should be 2 (Local system closed, FSM event follows).
This patch:
- adds definitions of all BGP FSM event codes per RFC4271
- changes the BMP reason code emitted when a peer changes state due to
NHT failure to 2 and encodes FSM event 18 (TcpConnectionFails)
- changes the catch-all case where we have not yet
implemented the appropriate BMP response to indicate reason code 2
with FSM event 0 (no relevant Event code is defined).
These changes ought to prevent the BMP session from being torn down due
to an improperly formatted message.
Signed-off-by: Quentin Young <qlyoung@qlyoung.net>
The logging code writes log messages with a `\n` line ending, meanwhile
the VTY code switches it so you need `\r\n`...
And we don't flush the newline after executing a command either.
After this patch, starting daemons like `zebra/zebra -t` should provide
a nice development/debugging experience with a VTY open right there on
stdio and `log stdout` interspersed.
(This is already documented in the man pages, it just looked like sh*t
previously since the log messages didn't newline correctly.)
Signed-off-by: David Lamparter <equinox@diac24.net>
... in case the user does something like `zebra 3>logfile`. Also useful
for some module purposes, maybe even feeding config at some point in the
future.
Signed-off-by: David Lamparter <equinox@diac24.net>
This command doesn't rely on transactional CLI and works perfectly for
daemons converted to northbound configuration.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
- Rfc 8050 adds support for BGP NLRI that carry path identifiers. this commit adds that support to FRR
- Updated bgp_dump.h to include new sub-type values
- Updated bgp_dump.c to check for add_path af_caps in the peer struct.
- Updated bgp_dump.c to use the proper sub-type values upon detection of add-path af_caps
- Updated bgp_dump.c to properly dump the path_id wen present.
Signed-off-by: David Teach <dteach@routeviews.org>
'show bgp ipv[46] vpn neighbors ... advertised-routes' was displaying
empty output due to new command syntax using show_adj_routes() which
assumed each bgp_table was single-tier (not nested). This fixes that
assumption for safis with a two-tier bgp_table (SAFI_MPLS_VPN,
SAFI_ENCAP, and SAFI_EVPN).
Before:
ub18# show bgp ipv6 vpn neighbors 2001:db8:cafe::2 advertised-routes
ub18#
After:
ub20# show bgp ipv6 vpn neighbors 2001:db8:cafe::1 advertised-routes
BGP table version is 2, local router ID is 100.64.0.222, vrf id 0
Default local pref 100, local AS 1
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 30:30
*> 2::2/128 :: 0 100 32768 i
*> 2::22/128 :: 0 100 32768 i
Route Distinguisher: 33:33
*> 2::2/128 :: 0 100 32768 i
*> 2::22/128 :: 0 100 32768 i
Total number of prefixes 4
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Currently when deleting a neighbor from a peer-group:
no neighbor A.B.C.D peer-group FOO
We must specify FOO, while A.B.C.D is sufficient enough of an
identifier to know what to do.
Make PGNAME optional on this command and just delete the peer.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Issue #7926 hilight a race condition in Segment Routing processing.
The problem occurs when Router Information Opaque LSA is received late, in
particular after SPF run and after ospf_sr_nhlfe_update() was called. This
scenario is unfrequent and takes place due to a slow DR election.
In this particular case, SR Prefix are handle but not fully fill. In fact,
SRGB for the nexthop is not yet received and thus, output label could not
be computed.
When Router Information Opaque LSA is received and processed, if the
corresponding SR node is a direct neighbor of the self node, update_out_nhlfe()
is called against all SR nodes to adjust SR prefix if the next hop is the new
SR node. The function wrongly computes output label and configure a bad MPLS
LFIB entries.
Another way to hilight the problem is to change through CLI the SRGB of a node
and look to MPLS LFIB of direct neighbor, in particular those who announce
EXPLICIT NULL Prefix SID.
This patch correct the update_out_nhlfe() function by calling the appropriate
function (sr_prefix_out_label() instead of index2label()) to compute the output
label.
Some log debugs were adjusted and unused prefix route table was removed too.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Currently if the sysctl net.ipv4.raw_l3mdev_accept is 1, packets
destined to a specific vrf also end up being delivered to the default
vrf. We will see logs like this in ospf:
2021/02/10 21:17:05.245727 OSPF: ospf_recv_packet: fd 20(default) on interface 1265(swp1s1.26)
2021/02/10 21:17:05.245740 OSPF: Hello received from [9.9.36.12] via [swp1s1.26:200.254.26.13]
2021/02/10 21:17:05.245741 OSPF: src [200.254.26.14],
2021/02/10 21:17:05.245743 OSPF: dst [224.0.0.5]
2021/02/10 21:17:05.245769 OSPF: ospf_recv_packet: fd 45(vrf1036) on interface 1265(swp1s1.26)
2021/02/10 21:17:05.245774 OSPF: Hello received from [9.9.36.12] via [swp1s1.26:200.254.26.13]
2021/02/10 21:17:05.245775 OSPF: src [200.254.26.14],
2021/02/10 21:17:05.245777 OSPF: dst [224.0.0.5]
This really really makes ospf unhappy in the vrf we are running in.
I am approaching the problem by just dropping the packet if read in the
default vrf because of:
commit 0556fc33c7
Author: Donald Sharp <sharpd@cumulusnetworks.com>
Date: Fri Feb 1 11:54:59 2019 -0500
lib: Allow bgp to always create a listen socket for the vrf
Effectively if we have `router ospf vrf BLUE` but no ospf running
in the default vrf, we will not have a listener and that would
require a fundamental change in our approach to handle the ospf->fd
at a global level. I think this is less than ideal at the moment
but it will get us moving again and allow FRR to work with
a bunch of vrf's and ospf neighbors.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
There are cases where nhrp wants to create a nhrp route to gre interface
with the nexthop which is the same the prefix. This is the case with
ipv6:
ipv6 route a:ff::ff:4/128 via a:ff::ff:4:/128 dev gre1
This route entry is false from zebra point of view, and to avoid that,
the nexthop is ignored in nhrp only if the prefix equals the nexthop.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Previously, when a shortcut entry was created, its associated route was
created on system, with no nexthop, only gre device. eg:
[..]
N>* 192.168.2.0/24 [10/0] is directly connected, gre1, 00:01:04 <--- can not be resolved
[..]
Type Prefix Via Identity
dynamic 192.168.2.0/24 10.255.255.2 <---- correct
This situation was forcing neighbor resolution on the first outgoing packet matching the route entry. for instance 192.168.2.1 could not be resolved at link layer, and was going to fail. Instead, nhrp nexthop should have been used.
This is what this commit intends to do, that is to say that when a
shortcut is installed by nhrp, the associated nexthop entry is used.
[..]
N>* 192.168.2.0/24 [10/0] via 10.255.255.2, gre1 onlink, 00:00:31
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
mallinfo() is deprecated as of glibc 2.33 and emits a warning if used.
Support mallinfo2() if available.
Signed-off-by: Quentin Young <qlyoung@qlyoung.net>
Issue: When a path in the inter area ecmp route is deleted, the route is removed
Fix: The fix is to remove the specific path from the inter area route using
ospf6_abr_old_route_remove() when abr route entry is not found.
In the function ospf6_abr_old_route_remove() the path to be removed needs
to match adv router and link state ID
Fixed memory leak in ospf6_intra_prefix_update_route_origin() caused by
route node lock not getting released.
Signed-off-by: kssoman <somanks@gmail.com>
The VRF must be marked as configured when user enters "vrf NAME" command.
Otherwise, the following problem occurs:
`ip link add red type vrf table 1`
VRF structure is allocated.
`vtysh -c "conf t" -c "vrf red"`
`lib_vrf_create` is called, and pointer to the VRF structure is stored
to the nb_config_entry.
`ip link del red`
VRF structure is freed (because it is not marked as configured), but
the pointer is still stored in the nb_config_entry.
`vtysh -c "conf t" -c "no vrf red"`
Nothing happens, because VRF structure doesn't exist. It means that
`lib_vrf_destroy` is not called, and nb_config_entry still exists in
the running config with incorrect pointer.
`ip link add red type vrf table 1`
New VRF structure is allocated.
`vtysh -c "conf t" -c "vrf red"`
`lib_vrf_create` is NOT called, because the nb_config_entry for that
VRF name still exists in the running config.
After that all NB commands for this VRF will use incorrect pointer to
the freed VRF structure.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Extend the thread_cancel_event api so that it's more complete:
look in all the lists of events, including io and timers, for
matching tasks. Add a limited version of the api that only
examines tasks in the event and ready queues.
BGP appears to require the old behavior, so change its macro
to use the more limited cancel api.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
No reason for the thread/task cancellation struct to be public:
move it out of the header file. Also add a flags field.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Modify code to add JSON format output in show command.
"show ip igmp [vrf NAME] join" and "show ip igmp vrf all join" with proper formatting
Signed-off-by: Sai Gomathi <nsaigomathi@vmware.com>
Modify the timers on the bgp_blackhole_community test to
be more aggressive so our test system will recover faster
when we drop packets.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
`same_attr` has been computed and `hook_call(bgp_process)` (calling
BMP module) would not change it. We could reuse the value to filter
same attribute updates, avoiding an extra comparison.
Signed-off-by: zyxwvu Shi <i@shiyc.cn>
