Problem Statement:
=================
When show ipv6 ospf6 neighbor is executed each neighbor gets
displayed twice.
frr# show ipv6 ospf6 neighbor
Neighbor ID Pri DeadTime State/IfState Duration I/F[State]
1.1.1.1 1 00:00:39 Full/DR 00:00:10 ens192[BDR]
1.1.1.1 1 00:00:39 Full/DR 00:00:10 ens192[BDR]
RCA:
====
Since ospf6_interface gets added twice to if_list we see multiple
display output.
Fix:
====
add ospf6_interface to if_list only when newly area gets attached
to the interface. If its already added no need to add it again.
Risk:
=====
Low
Tests Executed:
===============
Have tested the defect scenario.
frr# show ipv6 ospf6 neighbor
Neighbor ID Pri DeadTime State/IfState Duration I/F[State]
1.1.1.1 1 00:00:35 Full/DR 00:36:04 ens192[BDR]
frr#
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
ospf6_asbr_redistribute_unset must not be called if the redistribution
is not yet configured, because it decrements redistribution counter and
makes it negative in this case.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
If we have the following configuration:
```
vrf red
smth
exit-vrf
!
interface red vrf red
smth
```
And we delete the VRF using "no vrf red" command, we end up with:
```
interface red
smth
```
Interface config is preserved but moved to the default VRF.
This is not an expected behavior. We should remove the interface config
when the VRF is deleted.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
During the database description exchange process, the slave
releases the last dbdesc packet after router_dead_interval.
This was not implemented in the code.
I have written the function ospf6_neighbor_last_dbdesc_release,
which releases the last dbdesc packet after router_dead_interval.
This change was required as per the conformance test 13.11:
In state Full reception of a Database Description packet from
the master after this interval (RouterDeadInterval) will
generate a SeqNumberMismatch neighbor event.
Associated Parameters
ICMPv6 Packet Listen Time
ICMPv6 Packet Tolerance Factor
ICMPv6 Packet Tolerance Time
OSPFV3 DUT Interface Transmit Delay
OSPF Reset Adjacencies Timeout
Test Actions
1.
2. 3.
ANVL: Establish full adjacency with DUT for neighbor Rtr-0-A on DIface-0, with DUT as slave.
ANVL: Wait (for <RouterDeadInterval> seconds).
ANVL: Send <OSPF-DD> packet from neighbor Rtr-0-A to DIface-0 con- taining:
• •
I-bit field not set M-bit field not set
MS-bit field set
DD sequence number same as the one last sent by ANVL.
. ANVL: Listen (for upto 2 * <RxmtInterval> seconds) on DIface-0.
5. DUT: Trigger the event SeqNumberMismatch and set the neighbor state for neighbor Rtr-0-A to ExStart.
6. DUT: Send <OSPF-DD> packet.
7. ANVL: Verify that the received <OSPF-DD> packet contains:
• I-bit field set
• M-bit field set
• MS-bit field set.
Test Reference
• RFC 5340, s4.2.1.2 p19 Sending Database Description Packets
RFC 2328, s10.8 p104 Sending Database Description Packets.
Signed-off-by: Yash Ranjan <ranjany@vmware.com>
In RFC 2328 seqnumber 0x80000000 is reserved and not used. If an LSA
is received with seqnumber the LSA is now dropped and a debug error log
is printed.
Signed-off-by: Lynne Morrison <lynne@voltanet.io>
For redistribute commands if route map is set, then route takes it's metric
values from the route map. But in the case that routemap is set but the
metric for the route map is not, then the route metric is set to type-1.
Check if the metric is set for the routemap. If not then set it as per
redistributed default values (type 2)
Signed-off-by: Yash Ranjan <ranjany@vmware.com>
The default values will be set at the time of ospf6_redist_add
similar to ospfv2. Hence the default values will change as well.
Default metric type = E2
Default metic value = 20
Signed-off-by: Yash Ranjan <ranjany@vmware.com>
allow amount of work done by read and write threads in a single
invocation to be tuned to between 1 and 100 packets (default 20)
Signed-off-by: Pat Ruddy <pat@voltanet.io>
On transmit and receive calculate the time since the last hello was seen
and log a warning if it is late by more than the hello period.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
queue outgoing lsupdate messages to the interface tx FIFO and schedule
the ospf_write task to deal with them.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
enqueue outgoing dbdesc messages to the end of the tx FIFO and
schedule the ospf6_write task to deal with them.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
Add per interface fifo and per instance write list as a precursor
to implementing fairer sharing of the ospf6 oscket resources.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
To ensure we read all the datagrams availabe from a socket when the
read task is scheduled, make the read helper return and error or
continue enum and loop unitl an error is received.
This requires the read from the socket to be non blocking
Signed-off-by: Pat Ruddy <pat@voltanet.io>
Take the contents of ospf6_receive and split the funtionality that
deals with a single packet receipt and place it in a separate helper
function.
This is the first step in a refactor process to allow the ospf6_read
task to read until failure.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
The logging in ospf6 is very verbose. If you turn on logging on a scaled
system you get too many logs. The problem is that there are some errors
that occur that are hidden behind the debug flags, and to see these errors
we currently need to turn on the debug logging. This change converts these
error logs to warnings and removes the debug flags.
Signed-off-by: Lynne Morrison <lynne@voltanet.io>
Some wires got crossed during a couple merges using/changing
this function.
Update it to its new name.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
The ospf6_is_router_abr is checking to see if ospfv3 is an abr router
and also setting values. Let's rename it too `ospf6_check_and_set_router_abr`
to more accurately reflect what it is doing.
Additionally fix coverity #1505176 where we were not checking the return
value of ospf6_is_router_abr like we did every other time. In this
case we don't care about the return value so indicate that we do not.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
There exists a code path where ospf6 could be NULL and passing
to a function where it would always be derefed is a bad idea.
Put some small code in place to prevent this and allow this to be debuged
if it happens in the future.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Currently the interface area is configured from the router node using
"interface IFNAME area ID" command. There are multiple problems with
this command:
- it is not in line with all other interface-related commands - other
parameters are configured from the interface node using "ipv6 ospf6"
prefix
- it is not in line with OSPFv2 - area is configured from the interface
node using "ip ospf area" command
- most importantly, it doesn't work correctly when the interface is in
a different VRF - instead of configuring the interface, it creates a
new fake interface and configuring it instead
To fix all the problems, this commit adds a new command to the interface
configuration node - "ipv6 ospf6 area ID". The purpose of the command is
completely the same, but it works correctly in a multi-VRF environment.
The old command is preserved for the backward compatibility, but the
warning is added that it is deprecated because it doesn't work correctly
with VRFs.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
The %p printf format specifier does already print the pointer address
with a leading "0x" prefix (indicating a hexadecimal number). There's
no need to add that prefix manually.
While here, replace explicit function names in log messages by
__func__.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Patch provided by Soman K.S. with small alterations.
Signed-off-by: Soman K.S <somanks@gmail.com>
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
The following is implemented.
1. Configuring area as NSSA.
2. Generating Type 7 LSA.
3. Conversion of Type 7 to Type 5 ( Default Behavior).
4. NSSA ABR selection.
Reviewed-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Co-authored-by: Kaushik <kaushiknath.null@gmail.com>
Co-authored-by: Soman K.S <somanks@gmail.com>
Signed-off-by: Kaushik <kaushiknath.null@gmail.com>
Ensure that if allocated route is not added to a table then it is
deleted to avoid leaking memory.
Add a new memory type for route table so that ospf6 routes can be
distinguished in the show memory output in isolation.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
