FRR implements a non-standard, but compatible approach for
sending update LSAs (it always send to 224.0.0.5) on P2MP
interfaces. This change makes it so acks are also sent to
224.0.0.5.
Since the acks are multicast, this allows an optimization
where we don't send back out the incoming P2MP interface
immediately allow time to rx multicast ack from neighbors
on the same net that rx'ed the original (multicast) update.
Signed-off-by: Lou Berger <lberger@labn.net>
Fix CI Failure test_ospf_type5_summary_tc45_p0
Problem Statement:
==================
Summarised LSA is not flushed in OSPFv2 in below scenario:
1. Configure summary-address in ospfv2
2. redistribute static and connected.
3. Check the LSAs are received on neighbor.
4. Now remove all OSPFv2 configs, so neighbor will still have the summarised LSA.
5. Configure router ospf with redistribute static and connected.
6. Check the DB, summarised LSA is present although the configuration is not present.
7. Now configure the summary-address and remove the configuration after sometime.
8. The summarised LSA will be still present.
RCA:
==================
When self originated LSA is received from the neighbor and that
LSA is summarised one, the LSA is refreshed but a flag is not set
due to which it was not able to remove it later.
Fix:
==================
Set the originated flag when refreshing summarised LSA.
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
Move `is_default_prefix` variations to `lib/prefix.h` and make the code
use the library version instead of implementing it again.
NOTE
----
The function was split into per family versions to cover all types.
Using `union prefixconstptr` is not possible due to static analyzer
warnings which cause CI to fail.
The specific cases that would cause this failure were:
- Caller used `struct prefix_ipv4` and called the generic function.
- `is_default_prefix` with signature using `const struct prefix *` or
`union prefixconstptr`.
The compiler would complain about reading bytes outside of the memory
bounds even though it did not take into account the `prefix->family`
part.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
RFC 3623 specifies the Graceful Restart enhancement to the OSPF
routing protocol. This PR implements support for the restarting mode,
whereas the helper mode was implemented by #6811.
This work is based on #6782, which implemented the pre-restart part
and settled the foundations for the post-restart part (behavioral
changes, GR exit conditions, and on-exit actions).
Here's a quick summary of how the GR restarting mode works:
* GR can be enabled on a per-instance basis using the `graceful-restart
[grace-period (1-1800)]` command;
* To perform a graceful shutdown, the `graceful-restart prepare ospf`
EXEC-level command needs to be issued before restarting the ospfd
daemon (there's no specific requirement on how the daemon should
be restarted);
* `graceful-restart prepare ospf` will initiate the graceful restart
for all GR-enabled instances by taking the following actions:
o Flooding Grace-LSAs over all interfaces
o Freezing the OSPF routes in the RIB
o Saving the end of the grace period in non-volatile memory (a JSON
file stored in `$frr_statedir`)
* Once ospfd is started again, it will follow the procedures
described in RFC 3623 until it detects it's time to exit the graceful
restart (either successfully or unsuccessfully).
Testing done:
* New topotest featuring a multi-area OSPF topology (including stub
and NSSA areas);
* Successful interop tests against IOS-XR routers acting as helpers.
Co-authored-by: GalaxyGorilla <sascha@netdef.org>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Remove previous log config
debug ospf graceful-restart helper
and just use
debug ospf graceful-restart
for everything related to OSPF GR.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
Log the LSA advertising router in addition to the LSA type and
ID in the places where that information is necessary to uniquely
identify the LSA in the LSDB.
This is useful, for example, to know exactly which LSA has changed
when the router is exiting from the GR helper mode when a topology
change was detected.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Replaces some hard-coded function names with __func__,
adds some additional references to neighbor/interface,
and cleans up some debug strings to be more readable.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Description:
Apis for creating/deleting aggregate routes.
Origination of summary route on behalf of matched external routes.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Remove mid-string line breaks, cf. workflow doc:
.. [#tool_style_conflicts] For example, lines over 80 characters are allowed
for text strings to make it possible to search the code for them: please
see `Linux kernel style (breaking long lines and strings)
<https://www.kernel.org/doc/html/v4.10/process/coding-style.html#breaking-long-lines-and-strings>`_
and `Issue #1794 <https://github.com/FRRouting/frr/issues/1794>`_.
Scripted commit, idempotent to running:
```
python3 tools/stringmangle.py --unwrap `git ls-files | egrep '\.[ch]$'`
```
Signed-off-by: David Lamparter <equinox@diac24.net>
We test nbr->oi in a couple of places for null, but
in the majority of places of the nbr->oi data is being
used we just access it. Touch up code to trust this
assertion and make the code more consistent in others.
Found in Coverity.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This commit has:
The received packet path in ospf, had absolutely no debugs associated with
it. This makes it extremely hard to know when we receive packets for
consumption. Add some breadcrumbs to this end.
Large chunks of commands have no ability to debug what is happening
in what vrf. With ip overlap X vrf this becomes a bit of a problem
Add some breadcrumbs here.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We have a bunch of places that look for ORIGINAL_CODING. There is
nothing in our configure system to define this value and a quick
git blame shows this code as being original to the import a very
very long time ago. This is dead code, removing.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
ospf->external[DEFAULT_ROUTE] and zclient->default_information don't
line up with each other; the former is only used for "originate always".
Fixes: #4237
Signed-off-by: David Lamparter <equinox@diac24.net>
This reverts commit a6b4e1fded.
This fix is wrong too. The zclient->redist & ->mi_redist arrays are
accessed past their size for any external route that is not 0.0.0.0/0.
Also, it is incorrect to check default_information for DEFAULT_ROUTE
since that's "originate always".
Signed-off-by: David Lamparter <equinox@diac24.net>
Some daemons like ospfd and isisd have the ability to advertise a
default route to their peers only if one exists in the RIB. This
is what the "default-information originate" commands do when used
without the "always" parameter.
For that to work, these daemons use the ZEBRA_REDISTRIBUTE_DEFAULT_ADD
message to request default route information to zebra. The problem
is that this message didn't have an AFI parameter, so a default route
from any address-family would satisfy the requests from both daemons
(e.g. ::/0 would trigger ospfd to advertise a default route to its
peers, and 0.0.0.0/0 would trigger isisd to advertise a default route
to its IPv6 peers).
Fix this by adding an AFI parameter to the
ZEBRA_REDISTRIBUTE_DEFAULT_{ADD,DELETE} messages and making the
corresponding code changes.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Default route type is not considered while processing lsa
refresh timer expiry which intern makes it flushed from lsdb.
Signed-off-by: rgirada <rgirada@vmware.com>
In all but one instance we were following this pattern
with ospf_lsa_new:
ospf_lsa_new()
ospf_lsa_data_new()
so let's create a ospf_lsa_new_and_data to abstract
this bit of fun and cleanup all the places where
it assumes these function calls can fail.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we first get a packet, we need to know if we are self
originated later to make correct decisions. Go ahead and
note that we do not plan to make any decision points
about our self origination here.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Fix a || && mixup.
Add an assert for area to show we expect it to be non-null
going forward.
When memory is allocated if it fails we abort then
no need to check for null.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Currently, ospf external routers are part of struct
ospf_master which is not vrf aware ospf instance.
All ospf external routes are injected/leaked into all
vrfs.
Moved ospf external routes db to struct ospf to make
vrf aware, such one external routes learnt in one vrf
is not leaked into another vrf.
Ticket:CM-18855
Testing Done:
Inject external route in non-default vrf x, validated
ospf database across the vrf x, validated ospf routes
for vrf x.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Router-ID change or ospf instance going down,
send LS-Upd with MAXAGE to self origintated LSAs to
all ospf neighbors.
Ticket:CM-1576
Testing Done:
Bring R1 - R2, Change Router-ID on R2, restart frr on R2
Validated R1 ospf LSDB for max aged 3600 LSA from R2.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
This reverts commit c14777c6bf.
clang 5 is not widely available enough for people to indent with. This
is particularly problematic when rebasing/adjusting branches.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
log.c provides functionality for associating a constant (typically a
protocol constant) with a string and finding the string given the
constant. However this is highly delicate code that is extremely prone
to stack overflows and off-by-one's due to requiring the developer to
always remember to update the array size constant and to do so correctly
which, as shown by example, is never a good idea.b
The original goal of this code was to try to implement lookups in O(1)
time without a linear search through the message array. Since this code
is used 99% of the time for debugs, it's worth the 5-6 additional cmp's
worst case if it means we avoid explitable bugs due to oversights...
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
The FSF's address changed, and we had a mixture of comment styles for
the GPL file header. (The style with * at the beginning won out with
580 to 141 in existing files.)
Note: I've intentionally left intact other "variations" of the copyright
header, e.g. whether it says "Zebra", "Quagga", "FRR", or nothing.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This ditches tv_add, tv_sub, tv_cmp, etc. in favour of
monotime{,_since,_until}() which actually makes the code much more
readable in some locations.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
HAVE_OPAQUE_LSA is used by default and you have to actively turn it off
except that OPAQUE_LSA is an industry standard and used pretty much
everywhere. There is no need to have special #defines for this anymore.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
(cherry picked from commit 36fef5708d074a3ef41f34d324c309c45bae119b)
When considering small networks that have extreme requirements on
availability and thus convergence delay, the timers given in the OSPF RFC
seem a little “conservative”, i.e., the delay between accepted LSAs and the
rate at which LSAs are sent. Cisco introduced two commands 'timers throttle
lsa all’ and 'timers lsa arrival’, which allow operators to tune these
parameters.
I have been writing a patch to also support 'timers lsa arrival’ fully and
‘timers throttle lsa all’ (without the throttling part) also in quagga.
* Opaque support contains some kind of hack/optimisation to
origination/flooding to suppress some origins/floods until an opaque LS
Acks are received. Previous versions of the code have already been shown
to have bugs in them (see e16fd8a5, e.g.). It seems over-complex and fragile,
plus its conceptually the wrong place to try implement flooding hacks that,
AFAICT, do not depend particularly on the semantics of opaque LSA.
Nuke.
Tested-by: Olivier Dugeon <olivier.dugeon@orange.com>
