When a BFD integrated session already exists setting the profile
doesn't cause a session update (or vice versa): fix this issue by
handling the other cases.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Let the integration protocol always send the full configuration
instead of saving a few bytes. It will also allow protocols to specify
source address for IPv4 single hop connections and interface for multi
hop configuration.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Manage the main pthread's signal mask to avoid a signal-handling
race. Before entering poll, check for pending signals that the
application needs to handle. Use ppoll() to re-enable those
signals during the poll call.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Add an api that blocks application-handled signals (SIGINT,
SIGTERM, e.g.) then tests whether any signals have been received.
This helps to manage a race between signal reception and the poll
call in the main event loop.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
json_array_string_add is used to add a string entry into a JSON
list. This API is needed by zebra so moving it from bgpd to lib.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
DF (Designated forwarder) election is used for picking a single
BUM-traffic forwarded per-ES. RFC7432 specifies a mechanism called
service carving for DF election. However that mechanism has many
disadvantages -
1. LBs poorly.
2. Doesn't allow for a controlled failover needed in upgrade
scenarios.
3. Not easy to hw accelerate.
To fix the poor performance of service carving alternate DF mechanisms
have been proposed via the following drafts -
draft-ietf-bess-evpn-df-election-framework
draft-ietf-bess-evpn-pref-df
This commit adds support for the pref-df election mechanism which
is used as the default. Other mechanisms including service-carving
may be added later.
In this mechanism one switch on an ES is elected as DF based on the
preference value; higher preference wins with IP address acting
as the tie-breaker (lower-IP wins if pref value is the same).
Sample output
=============
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
torm-11# sh bgp l2vpn evpn es 03:00:00:00:00:01:11:00:00:01
ESI: 03:00:00:00:00:01:11:00:00:01
Type: LR
RD: 27.0.0.15:6
Originator-IP: 27.0.0.15
Local ES DF preference: 100
VNI Count: 10
Remote VNI Count: 10
Inconsistent VNI VTEP Count: 0
Inconsistencies: -
VTEPs:
27.0.0.16 flags: EA df_alg: preference df_pref: 32767
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
torm-11# sh bgp l2vpn evpn route esi 03:00:00:00:00:01:11:00:00:01
*> [4]:[03:00:00:00:00:01:11:00:00:01]:[32]:[27.0.0.15]
27.0.0.15 32768 i
ET:8 ES-Import-Rt:00:00:00:00:01:11 DF: (alg: 2, pref: 100)
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
In transactional cli mode, bgp address-family <afi> <afi>
node builds xpath on top of `router bgp` node's xpath.
When `exit` is applied under afi-safi commands, retain
xpath_index to 1 to keep using bgp global xpath.
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Make it possible to load YANG modules outside the main northbound
initialization. The primary use case is to support YANG modules
that are specific to an FRR plugin. Example: only load the PCEP
YANG module when the corresponding FRR plugin is loaded. Other use
cases might arise in the future.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Combine yang_snodes_iterate_module() and yang_snodes_iterate_all()
into an unified yang_snodes_iterate() function, where the first
"module" parameter is optional. There's no point in having two
separate YANG schema iteration functions anymore now that they are
too similar.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The only safe way to iterate over all schema nodes of a given YANG
module is by iterating over all schema nodes of all YANG modules
and filter out the nodes that belong to other modules.
The original yang_snodes_iterate_module() code did the following:
1 - Iterate over all top-level schema nodes of the given module;
2 - Iterate over all augmentations of the given module.
While that iteration strategy is more efficient, it does't handle
well more complex YANG hierarchies containing nested augmentations
or self-augmenting modules. Any iteration that isn't done on the
resolved YANG data hierarchy is fragile and prone to errors.
Fixes regression introduced by commit 8a923b4851 where the
gen_northbound_callbacks tool was generating duplicate callbacks
for certain modules.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
- tracepoint() -> frrtrace()
- tracelog() -> frrtracelog()
- tracepoint_enabled() -> frrtrace_enabled()
Also removes copypasta'd #ifdefs for those LTTng macros, those are
handled in lib/trace.h
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Previous commits added LTTng tracepoints. This was primarily for testing
/ trial purposes; in practice we'd like to support arbitrary tracing
methods, and especially USDT probes, which SystemTap and dtrace expect,
and which are supported on at least one flavor of BSD (FreeBSD).
To that end this patch adds an frr-specific tracing macro, frrtrace(),
which proxies into either DTRACE_PROBEn() or tracepoint() macros
depending on whether --enable-usdt or --enable-lttng is passed at
compile time.
At some point this could be tweaked to allow compiling in both types of
probes. Ideally there should be some logic there to use LTTng's optional
support for generating USDT probes when both are requested.
No additional libraries are required to use USDT, since these probes are
a kernel feature and only need the <sys/sdt.h> header.
- add --enable-usdt to toggle use of LTTng tracepoints or USDT probes
- add new trace.h library header for use with tracepoint definition
headers
- add frrtrace() wrapper macro; this should be used to define
tracepoints instead of using tracepoint() or DTRACE_PROBEn()
Compilation with USDT does nothing as of this commit; the existing LTTng
tracepoints need to be converted to use the frrtrace*() macros in a
subsequent commit.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
hash_get is used for both lookup and insert; add a tracepoint for when
we insert something into the hash
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
LTTng supports tracef() and tracelog() macros, which work like printf,
and are used to ease transition between logging and tracing. Messages
printed using these macros end up as trace events. For our uses we are
not interested in dropping logging, but it is nice to get log messages
in trace output, so I've added a call to tracelog() in zlog that dumps
our zlog messages as trace events.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
This commit adds initial support for LTTng.
When --enable-lttng=no or is not specified, no tracing code is included.
When --enable-lttng=yes, LTTng tracing events are (will be) generated.
configure.ac:
- add --enable-lttng
- define HAVE_LTTNG when enabled
- minimum LTTng version: 2.12.0
lib:
- add trace.[ch]
- update subdir.am
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Replace all lib/thread cancel macros, use thread_cancel()
everywhere. Only the THREAD_OFF macro and thread_cancel() api are
supported. Also adjust thread_cancel_async() to NULL caller's pointer (if
present).
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Change thread_cancel to take a ** to an event, NULL-check
before dereferencing, and NULL the caller's pointer. Update
many callers to use the new signature.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Convert over to using the %pFX and %pRN modifiers
to output strings to allow us to consolidate on
one standard for printing prefixes.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Create appropriate accessor functions for the rn->lock
data. We should be accessing this data through accessor
functions since it is private data to the data structure.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Currently the prefix length M must be less than Y.
Relax this restriction to allow M to be less than or equal
to Y.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
We have 2 different routines to turn an evpn route into a string.
This commit aligns the two to the latest maintained version as a
first step in removing one of them.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
Consolidate evpn type help strings into one single
macro for use on commands that need to support all
the types.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
We have this pattern in the code base:
if (thread)
THREAD_OFF(thread);
If we look at THREAD_OFF we check to see if thread
is non-null too. So we have a double check.
This is unnecessary. Convert to just using THREAD_OFF
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Display human readable error message in northbound rpc
transaction failure. In case of vtysh nb client, the error
message will be displayed to user.
Testing:
bharat# clear evpn dup-addr vni 1002 ip 11.11.11.11
Error type: generic error
Error description: Requested IP's associated MAC aa:aa:aa:aa:aa:aa is still
in duplicate state
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Don't attempt to compress the wildcard information to fit a `/M`, but
use its own full 4 byte field.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
