The bgp_info data is stored as a void pointer in `struct bgp_node`.
Abstract retrieval of this data and setting of this data
into functions so that in the future we can move around
what is stored in bgp_node.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
It's been a year since we added the new optional parameters
to instantiation. Let's switch over to the new name.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If we attempt to register nexthops before we have the zebra
connection, they will not be installed. After we have noticed
that we are up, re-install them.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow some debug notification when we are unable to talk
to zebra due to the connection not being there yet.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add the '[no] flood <disable|head-end-replication>' command
to the l2vpn evpn afi/safi sub commands for bgp. This command
when entered as 'flood disable' will turn off type 3 route
generation for the transmittal of the type 3 route necessary
for BUM replication on the remote VTEP. Additionally it will
turn off the BUM handling via the new zebra command,
ZEBRA_VXLAN_FLOOD_CONTROL.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow the modification of whether or not we will allow
BUM flooding on the vxlan bridge. To do this allow
the upper level protocol to specify via the ZEBRA_VXLAN_FLOOD_CONTROL
zapi message.
If flooding is disabled then BUM traffic will not be forwarded
to other VTEP's.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Do a straight conversion of `struct bgp_info` to `struct bgp_path_info`.
This commit will setup the rename of variables as well.
This is being done because `struct bgp_info` is not descriptive
of what this data actually is. It is path information for routes
that we keep to build the actual routes nexthops plus some extra
information.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In bgp if we have not configured bgp we were ignoring
interface based callbacks. Leading to states where
we may not be processing interface information.
Leading to states where we do not actually keep
ifp data. As an example:
Suppose vrf A and vrf B. A has interface swp1.
At the same time we only have a `router bgp 9 vrf B`
When we received the callback for moving swp1
from vrf A to vrf B we were not processing the
move at all and BGP would not consider the interface
part of vrf B at all.
This commit makes bgp pay attention to interface
events irrelevant if bgp is using that vrf. This
is now consistent with how the lib/if* expects
to work and the rest of the daemons in FRR.
Signed-off-by: Donald Sharp <sharpd@cumulsnetworks.com>
Corrections so that the BGP daemon can work with the label manager properly
through a label-manager proxy. Details:
- Correction so the BGP daemon behind a proxy label manager gets the range
correctly (-I added to the BGP daemon, to set the daemon instance id)
- For the BGP case, added an asynchronous label manager connect command so
the labels get recycled in case of a BGP daemon reconnection. With this,
BGPd and LDPd would behave similarly.
Signed-off-by: F. Aragon <paco@voltanet.io>
When using `no bgp fast-external-failover` and a interface moves
from one vrf into another we would not fully process the change.
Fix this code path.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The peer->nexthop.ifp pointer must be set when parsing the
attributes in bgp_mp_reach_parse, notice this
and fail gracefully.
Rework bgp_nexthop_set to remove the HAVE_CUMULUS and to
fail the nexthop_set when we have a zebra connection and
no ifp pointer, as that not havinga zebra connection and
no ifp pointer is legal.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
* Added parameter in bgp_redistribute_set() to indicate change
in redistribute option
* If there is change, call bgp_redistribute_unreg() to withdraw routes
Signed-off-by: kssoman <somanks@vmware.com>
Implement procedures similar to what is specified in
https://tools.ietf.org/html/draft-malhotra-bess-evpn-irb-extended-mobility
in order to support extended mobility scenarios in EVPN. These are scenarios
where a host/VM move results in a different (MAC,IP) binding from earlier.
For example, a host with an address assignment (IP1, MAC1) moves behind a
different PE (VTEP) and has an address assignment of (IP1, MAC2) or a host
with an address assignment (IP5, MAC5) has a different assignment of (IP6,
MAC5) after the move. Note that while these are described as "move" scenarios,
they also cover the situation when a VM is shut down and a new VM is spun up
at a different location that reuses the IP address or MAC address of the
earlier instance, but not both. Yet another scenario is a MAC change for an
attached host/VM i.e., when the MAC of an attached host changes from MAC1 to
MAC2. This is necessary because there may already be a non-zero sequence
number associated with MAC2. Also, even though (IP, MAC1) is withdrawn before
(IP, MAC2) is advertised, they may propagate through the network differently.
The procedures continue to rely on the MAC mobility extended community
specified in RFC 7432 and already supported by the implementation, but
augment it with a inheritance mechanism that understands the relationship
of the host MACIP (ARP/neighbor table entry) to the underlying MAC (MAC
forwarding database entry). In FRR, this relationship is understood by the
zebra component which doubles as the "host mobility manager", so the MAC
mobility sequence numbers are determined through interaction between bgpd
and zebra.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Because one flowspec entry can create 1-N bgp pbr entries, the list is
now updated and visible. Also, because the bgp_extra structure is used,
this list is flushed when the bgp_extra structure is deleted.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This commit removes various parts of the bgpd implementation code which
are unused/useless, e.g. unused functions, unused variable
initializations, unused structs, ...
Signed-off-by: Pascal Mathis <mail@pascalmathis.com>
The flowspec fragment attribute is taken into account to be pushed in
BGP policy routing entries. Valid values are enumerate list of 1, 2, 4,
or 8 values. no combined value is supported yet.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The rearrangement of where the decision point of
filling in the aggregate information, must have allowed
SA to find a path of code where we may use ifindex uninitialized.
While I don't think this is possible to happen, make this issue
go away.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The aggregate-address command is not creating the null0
route. This got lost somewhere in the last year or so.
Add this ability back for BGP route installs into
zebra.
We need this aggregate route installed into the rib
because we are drawing this traffic to us irrelevant
of the number of routes we do have for that prefix.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Sometimes at startup, BGP Flowspec may be allocated a routing table
identifier not in the range of the predefined table range.
This issue is due to the fact that BGP peering goes up, while the BGP
did not yet retrieve the Table Range allocator.
The fix is done so that BGP PBR entries are not installed while
routing table identifier range is not obtained. Once the routing table
identifier is obtained, parse the FS entries and check that all selected
entries are installed, and if not, install it.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
By default, some debug traces were displayed. Those pbr traces are
hidden with 'debug bgp zebra' command.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
policy routing is configurable via address-family ipv4 flowspec
subfamily node. This is then possible to restrict flowspec operation
through the BGP instance, to a single or some interfaces, but not all.
Two commands available:
[no] local-install [IFNAME]
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Once PBR rules installed, an information is printed in the main
show bgp ipv4 flowspec detail information.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Those 3 fields are read and written between zebra and bgpd.
This permits extending the ipset_entry structure.
Combinatories will be possible:
- filtering with one of the src/dst port.
- filtering with one of the range src/ range dst port
usage of src or dst is exclusive in a FS entry.
- filtering a port or a port range based on either src or dst port.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When rule add transaction is sent from bgpd to zebra, the reference
context must not be incremented while the confirmation message of
install has not been sent back; unless if the transaction failed to be
sent.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The debugging message in charge of showing if the route is added or
witdrawn is changed accordingly to reflect this status.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Ensure that the next hop of the leaked VRF is not overwritten when the
route is being imported into the target VRF from the VPN table. Also, in
the case of multipath routes, ensure that the nexthop's ifindex is not
inadvertently reset.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Ensure that when EVPN routes are installed into zebra, the router MAC
is passed per next hop and appropriately handled. This is required for
proper multipath operation.
Ticket: CM-18999
Reviewed By:
Testing Done: Verified failed scenario, other manual tests
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
All messages to/from the label manager include two additional
fields: protocol and instance. This patch fixes the parsing
of label chunks response used by BGPd, which did not consider
the two fields.
Signed-off-by: Fredi Raspall <fredi@voltanet.io>
Upon BGP destroy, the hash list related to PBR are removed.
The pbr_match entries, as well as the contained pbr_match_entries
entries.
Then the pbr_action entries. The order is important, since the former
are referencing pbr_action. So the references must be removed, prior to
remove pbr action.
Also, the zebra associated contexts are removed.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Upon redirect VRF message from FS, add a default route to the VRF
interface associated to the VRF.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
A table chunk of 100000 is allocated from zebra, and when needed in
flowspec, the table identifier is extracted from that chunk.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
If a new rule is identified, a new table identifier is created.
In that table, add a default route when possible. If redirect IP rule is
identified, then add a default route to that IP address.
If redirect VRF is identified, nothing is done for now
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
once an iprule has been created, a notification is sent back, and the
context of bgp_action is searched.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The API for filling in an IPTABLE_ADD and IPTABLE_DELETE message.
Also, the API is handling the notification callback, so as to know if
zebra managed to add or delete the relevant iptable entry.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The APIs that handle ipset and iprule contexts from zebra are being
handled in this commit.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
There were a couple of instances of code extending
beyond 80 columns, clean it up with clang-format.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Connected routes redistributed into BGP as well as IPv4 routes with IPv6
link-local next hops (RFC 5549) need information about the associated
interface in BGP if they are candidates to be leaked into another VRF. In
the absence of route leaking, this was not necessary. Introduce the
appropriate mechanism and ensure this is used during route install (in
the target VRF).
Ticket: CM-20343, CM-20382
Testing done:
1. Manually verified failed scenarios and some additional ones - logs
in the tickets.
2. Ran bgp-min and evpn-min - results are good.
3. Ran vrf smoke - has some failures, but none which look new
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
When routes are imported into a VRF from the global VPN table, the
parent instance is either the default instance in the case of L3VPN or
the source VRF in the case of VRF-to-VRF route leaking. Hence, obtain
the source peer by just looking at the parent route information.
Ticket: CM-20283
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
When sending a bgp route down to zebra for deletion, the
ZEBRA_FLAG_ALLOW_RECURSION and ZEBRA_FLAG_IBGP flags
are not needed in zebra. So remove the setting
of the api.flags. If we remove this data from being
passed down we no longer need the peer data structure.
Remove the lookup of the peer data structure and the setting
of the flags as that peer was NULL in some evpn symmetric
routing cases for shutdown of bgp.
Ticket: CM-20720
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add support for CLI "auto" keyword in vrf->vpn export label:
router bgp NNN vrf FOO
address-family ipv4 unicast
label vpn export auto
exit-address-family
Signed-off-by: G. Paul Ziemba <paulz@labn.net>
MPLS label pool backed by allocations from the zebra label manager.
A caller requests a label (e.g., in support of an "auto" label
specification in the CLI) via lp_get(), supplying a unique ID and
a callback function. The callback function is invoked at a later
time with the unique ID and a label value to inform the requestor
of the assigned label.
Requestors may release their labels back to the pool via lp_release().
The label pool is stocked with labels allocated by the zebra label
manager. The interaction with zebra is asynchronous so that bgpd
is not blocked while awaiting a label allocation from zebra.
The label pool implementation allows for bgpd operation before (or
without) zebra, and gracefully handles loss and reconnection of
zebra. Of course, before initial connection with zebra, no labels
are assigned to requestors. If the zebra connection is lost and
regained, callbacks to requestors will invalidate old assignments
and then assign new labels.
Signed-off-by: G. Paul Ziemba <paulz@labn.net>
Routes that have labels must be sent via a nexthop that also has labels.
This change notes whether any path in a nexthop update from zebra contains
labels. If so, then the nexthop is valid for routes that have labels.
If a nexthop update has no labeled paths, then any labeled routes
referencing the nexthop are marked not valid.
Add a route flag BGP_INFO_ANNC_NH_SELF that means "advertise myself
as nexthop when announcing" so that we can track our notion of the
nexthop without revealing it to peers.
Signed-off-by: G. Paul Ziemba <paulz@labn.net>
Ensure that only EVPN routes are flagged as such when installing into or
withdrawing from zebra, the earlier check broke L3VPN or VRF route-leaked
routes. Also, fix an incorrect check related to imported routes in path
selection.
Updates: bgpd: Use BGP_ROUTE_IMPORTED for EVPN [vivek]
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
BGP is calculating a v6 routes nexthop as the nexthop address
+ an ifindex. The ifindex calculated comes from where we received
the route from as that we have to do this for LL addresses.
But a v6 address that is not a LL we do not need to provide
to zebra for nexthop resolution because a global address
by default can be looked up and resolved appropriately.
Modify the code so that we must have an ifindex for a v6 nexthop
if the address is LL, else don't pass the ifindex down to zebra.
Fixes: #1986
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In BGP, doing policy-routing requires to use table identifiers.
Flowspec protocol will need to have that. 1 API from bgp zebra has been
done to get the table chunk.
Internally, onec flowspec is enabled, the BGP engine will try to
connect smoothly to the table manager. If zebra is not connected, it
will try to connect 10 seconds later. If zebra is connected, and it is
success, then a polling mechanism each 60 seconds is put in place. All
the internal mechanism has no impact on the BGP process.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The following types are nonstandard:
- u_char
- u_short
- u_int
- u_long
- u_int8_t
- u_int16_t
- u_int32_t
Replace them with the C99 standard types:
- uint8_t
- unsigned short
- unsigned int
- unsigned long
- uint8_t
- uint16_t
- uint32_t
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
When uninstalling routes from zebra, ensure that the BGP instance for
which processing is being done is used to derive the VRF. It is incorrect
to derive the VRF from the peer when dealing with scenarios like VRF route
leaking, EVPN symmetric/external routing etc., where the peer which sourced
the route could belong to a different VRF.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
Ticket: CM-18413
Reviewed By: CCR-6778
Testing Done: Manual testing of BGP route withdraw/delete, bgp-min
PR #1739 added code to leak routes between (default VRF) VPN safi and unicast RIBs in any VRF. That set of changes included temporary CLI including vpn-policy blocks to specify RD/RT/label/&c. After considerable discussion, we arrived at a consensus CLI shown below.
The code of this PR implements the vpn-specific parts of this syntax:
router bgp <as> [vrf <FOO>]
address-family <afi> unicast
rd (vpn|evpn) export (AS:NN | IP:nn)
label (vpn|evpn) export (0..1048575)
rt (vpn|evpn) (import|export|both) RTLIST...
nexthop vpn (import|export) (A.B.C.D | X:X::X:X)
route-map (vpn|evpn|vrf NAME) (import|export) MAP
[no] import|export [vpn|evpn|evpn8]
[no] import|export vrf NAME
User documentation of the vpn-specific parts of the above syntax is in PR #1937
Signed-off-by: G. Paul Ziemba <paulz@labn.net>
Set EVPN routes imported into a VRF to (sub)type BGP_ROUTE_IMPORTED and
use this for passing appropriate information to zebra. This is needed
because relying on the Router MAC for this purpose was incorrect and
impacted routing to/from external destinations, particularly for IPv6.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Place the nexthop vrf id setting outside the afi if split
so that each side does not need to keep track of this.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
- add "debug bgp vpn label" CLI
- improved debug messages for "debug bgp bestpath"
- send vrf label to zebra after zebra informs bgpd of vrf_id
- withdraw vrf_label from zebra if zebra informs bgpd that vrf_id is disabled
Signed-off-by: G. Paul Ziemba <paulz@labn.net>
The ZEBRA_FLAG_INTERNAL flag is used to signal to zebra that
the route being added, the nexthops for it can be recursively
resolved. This name keeps throwing me off when I read it
so let's rename to something that allows the developer to
understand what is going on.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Asymmetric routing is an ideal choice when all VLANs are cfged on all leafs.
It simplifies the routing configuration and
eliminates potential need for advertising subnet routes.
However, we need to reach the Internet or global destinations
or to do subnet-based routing between PODs or DCs.
This requires EVPN type-5 routes but those routes require L3 VNI configuration.
This task is to support EVPN type-5 routes for prefix-based routing in
conjunction with asymmetric routing within the POD/DC.
It is done by providing an option to use the L3 VNI only for prefix routes,
so that type-2 routes (host routes) will only use the L2 VNI.
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
None of these variables can actually be used before being initialized,
but unfortunately some old compilers are not smart enough to detect that.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
When an IPv4 or IPv6 unicast route is injected into EVPN as a type-5 route
(upon user configuration), ensure that the source route (best path)'s path
attributes are used to build the EVPN type-5 route. This will result in
correct AS_PATH and ORIGIN attributes for the type-5 route so that it doesn't
appear that all type-5 routes are locally sourced. This is necessary to
ensure that external paths (IPv4 or IPv6 from EBGP peer) are preferred over
internal EVPN paths, if both exist.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Ticket: CM-19051
Reviewed By: CCR-7009
Testing Done: Verify failed scenario
In EVPN symmetric routing, not all subnets are presents everywhere.
We have multiple scenarios where a host might not get learned locally.
1. GARP miss
2. SVI down/up
3. Silent host
We need a mechanism to resolve such hosts. In order to achieve this,
we will be advertising a subnet route from a box and that box will help
in resolving the ARP to such hosts.
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
When doing symmetric routing,
EVPN type-2 (MACIP) routes need to be advertised with two labels (VNIs)
the first being the L2 VNI (identifying the VLAN) and
the second being the L3 VNI (identifying the VRF).
The receive processing needs to handle one or two labels too.
Ticket: CM-18489
Review: CCR-6949
Testing: manual and bgp/evpn/mpls smoke
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Problem reported that when "systemctl restart networking" was
performed, prefixes previously redistributed into bgp from connected
were deleted from the bgp table. Determined that we were not correctly
changing the redistribution bitmask when the vrf_id of the vrf was
changed. This patch corrects that behavior.
Manual tests look good. bgp-min and vrf-min completed with no new failures.
Ticket: CM-19369
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
For EVPN type-5 route the NH in the NLRI is set to the local tunnel ip.
This information has to be obtained from kernel notification.
We need to pass this info from zebra to bgp in l3vni call flow.
This patch doesn't handle the tunnel-ip change.
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
Allow the higher level protocol to specify if it would
like to receive notifications about it's routes that
it has installed.
I've purposely made it part of zclient_new_notify because
we need to track the routes on a per daemon basis only.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When BGP is being redistributed prefixes, allow it to
understand the nexthop type.
This fixes the issue where a blackhole route was being interpreted
to having a nexthop of 1.0.0.0( ruh-roh!!! ). This broke
downstream neighbors as that they would receive a 1.0.0.0 nexthop,
which is bad, very very bad.
This commit sets us up for the future where we can match
a route-map against a nexthop type. In that bgp is
now at least nominally paying attention to the type.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When bgp is coming up and is reading a non-integrated config.
The bgp connection to zebra has not fully had a chance to start.
As such when a redistribute line is parsed the attempt is
made to install it but it was erroring out with a warning.
This caused the `redistribute XXX` line to create a error
message to the end user.
Since bgp calls zclient_send_reg_requests which re-registers
the redistribute call once the actual zebra connection is up
and once bgp comes alive this is ok.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
In some situations we already know the ifp and by extension
the ifindex there is no need to look it up for every
route we send to zebra.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This improves code readability and also future-proofs our codebase
against new changes in the data structure used to store interfaces.
The FOR_ALL_INTERFACES_ADDRESSES macro was also moved to lib/ but
for now only babeld is using it.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Performance tests showed that, when running on a system with a large
number of interfaces, some daemons would spend a considerable amount
of time in the if_lookup_by_index() function. Introduce a new rb-tree
to solve this problem.
With this change, we need to use the if_set_index() function whenever
we want to change the ifindex of an interface. This is necessary to
ensure that the 'ifaces_by_index' rb-tree is updated accordingly. The
return value of all insert/remove operations in the interface rb-trees
is checked to ensure that an error is logged if a corruption is
detected.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
IFINDEX_DELETED is not necessary anymore as we moved from a global
list of interfaces to a list of interfaces per VRF.
This reverts commit 84361d615.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This is an important optimization for users running FRR on systems with
a large number of interfaces (e.g. thousands of tunnels). Red-black
trees scale much better than sorted linked-lists and also store the
elements in an ordered way (contrary to hash tables).
This is a big patch but the interesting bits are all in lib/if.[ch].
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Problem reported with the log displaying error messages if bgpd was
enabled in /etc/frr/daemons but bgp wasn't actually configured. The
problem was due to operating on interfaces before if_create had been
called (which happens at "router bgp" not at frr starting. Moved the
checks for the bgp instance before operating on interfaces. Manual
testing successful and bgp-smoke completed with no new issues.
Ticket: CM-13504
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: CCR-6738
list_free is occassionally being used to delete the
list and accidently not deleting all the nodes.
We keep running across this usage pattern. Let's
remove the temptation and only allow list_delete
to handle list deletion.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This is a fallout from PR #1022 (zapi consolidation). In the early days,
the client daemons would allocate enough memory to send all nexthops
to zebra. Then zebra would add all nexthops to the RIB and respect
MULTIPATH_NUM only when installing the routes in the kernel. Now things
are different and the client daemons can send at most MULTIPATH_NUM
nexthops to zebra, and failure to respect that will result in a buffer
overflow. The MULTIPATH_NUM limit in the new zebra API is a small price
we pay to avoid allocating memory for each route sent to zebra.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The previous code assumed that all nexthops of an ECMP route were of
the same address-family. This is not always the case.
Reported-by: Don Slice <dslice@cumulusnetworks.com>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
bgp_attr_deep_dup is based on a misunderstanding of how route-maps work.
They never change actual data, just pointers & fields in "struct attr".
The correct thing to do is copy struct attr and call bgp_attr_flush()
afterwards.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
FLAG_BLACKHOLE is used for different things in different places. remove
it from the zclient API, instead indicate blackholes as proper nexthops
inside the message.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Some differences compared to the old API:
* Now the redistributed routes are sent using address-family
independent messages (ZEBRA_REDISTRIBUTE_ROUTE_ADD and
ZEBRA_REDISTRIBUTE_ROUTE_DEL). This allows us to unify the ipv4/ipv6
zclient callbacks in the client daemons and thus remove a lot of
duplicate code;
* Now zebra sends all nexthops of the redistributed routes to the client
daemons, not only the first one. This shouldn't have any noticeable
performance implications and will allow us to remove an ugly exception
we had for ldpd (which needs to know all nexthops of the redistributed
routes). The other client daemons can simply ignore the nexthops if
they want or consult just the first one (e.g. ospfd/ospf6d/ripd/ripngd).
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The code path for a deleted interface was calling
zebra with a IFINDEX_DELETED, which caused zebra
to bitch and moan about the issue. Since the
only thing this function does is call zebra
to deregister the RA stuff, don't set the
ifindex to DELETED till afterwords.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This reverts commit c14777c6bf.
clang 5 is not widely available enough for people to indent with. This
is particularly problematic when rebasing/adjusting branches.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
This allows frr-reload.py (or anything else that scripts via vtysh)
to know if the vtysh command worked or hit an error.
Most of the attributes in 'struct attr_extra' allow for
the more interesting cases of using bgp. The extra
overhead of managing it will induce errors as we add
more attributes and the extra memory overhead is
negligible on anything but full bgp feeds.
Additionally this greatly simplifies the code for
the handling of data.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
bgpd: Fix missing label set
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Implement support for sticky (static) MACs. This includes the following:
- Recognize MAC is static (using NUD_NOARP flag) and inform BGP
- Construct MAC mobility extended community for sticky MACs as per
RFC 7432 section 15.2
- Inform to zebra that remote MAC is sticky, where appropriate
- Install sticky MACs into the kernel with the right flag
- Appropriate handling in route selection
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Core EVPN route handling functionality. This includes support for the
following:
- interface with zebra to learn about local VNIs and MACIPs as well as
to install remote VTEPs (per VNI) and remote MACIPs
- create/update/delete EVPN type-2 and type-3 routes
- attribute creation, route selection and install
- route handling per VNI and for the global routing table
- parsing of received EVPN routes and handling by route type
- encoding attributes for EVPN routes and EVPN prefix creation (for
Updates)
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Implement the command 'advertise-all-vni' under the EVPN address-family
in order to allow the local system to learn about local VNIs (and MACs
and Neighbors corresponding to those VNIs) and exchange with other EVPN
speakers.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
The if_update function was taking the interface name as
input and reapplying it, using strncpy to reapply the name.
This has several issues. strncpy should not be used
to copy memory in place. The second issue is that
the interface name is not actually changing when we
update interface to be in the new vrf.
Since every usage of if_update was just reapplying the same
name the interface actually had, just remove that part of
the function and rename it to if_update_to_new_vrf
to represent what it is actually doing.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The data for each nexthop is stored off of the info
pointer, instead of handling the first one and then looping
over the remaining, just loop over them all and handle the
first one as a special case.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
