Ticket:CM-6802, CM-6952
Reviewed By: Donald, Kanna
Testing Done:
Double commit of b76943235e09472ec174edcf7204fc82d27fe966 from br2.5. But, manually resolved all the compilation errors. Also, modified the shows to support the json format which was not supported in br2.5.
CM-6802 – Currently, BFD session status can be monitored only through ptmctl. There is no way to check the BFD status of a peer/neighbor through Quagga. Debugging becomes easier if BFD status is shown in Quagga too. BFD status is relevant when it is shown against the BGP peer/OSPF neighbor. For, this following code changes have been done:
- Only down messages from PTM were being propagated from Zebra daemon to clients (bgpd, ospfd and ospf6d). Now, both up and down messages are redistributed to the clients from zebra. BFD status field has been added to the messaging. Handling of BFD session up messages has been added to the client code. BGP/OSPF neighbor is brought down only if the old BFD session status is ‘Up’ to handle extra/initial down messages.
- BFD status and last update timestamp fields have been added to the common BFD info structure. Also, common show functions for showing BFD information have been added to BFD lib.
- Modified the BGP neighbor show functions to call common BFD lib functions.
- For ospf and ospf6, BFD information was maintained only at interface level. To show BFD status per neighbor, BFD information has been added at neighbor level too. “show ip ospf interface”, “show ip ospf neighbor detail”, “show ipv6 ospf6 interface” and “show ipv6 ospf6 neighbor detail” output have been modified to show BFD information.
CM-6952 - IBGP peers were always assumed to be multi-hop since there was no easy way to determine whether an IBGP peer was single hop or multihop unlike EBGP. But, this is causing problem with IBGP link local peers since BFD doesn't allow multihop BFD session with link local IP addresses. Link local peers were discovered when the interface peering was enabled. Interface peering is always singlehop. So, added checks to treat all interface based peers as single hop irrespective of whether the peer is IBGP or EBGP.
Ticket: CM-6520
Reviewed By: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed By: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-By: Morgan Stewart <morgan@cumulusnetworks.com>
Testing Done: Manual testing and smoketested
Whenever some sort of output is encountered, added a json version with
proper logic as well.
Allow configuration of faster OSPF convergence via the
min_ls_interval and min_ls_arrival timer lengths.
This patch was originated by Michael, and cross-ported
to Cumulus's Quagga.
Signed-off-by: Michael Rossberg <michael.rossberg@tu-ilmenau.de>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: Trivial
Reviewed by: Trivial
Testing: arm/powerpc/amd64 targets now build
Apparently we have a arm build. Who knew? This fixes the compile warnings/errors
produced when you compile a arm build with -Werror.
OSPF BFD command enhancement to configure BFD parameters (detect multiplier, min rx and min tx).
interface <if-name>
ip ospf bfd <detect mult> <min rx> <min tx>
This patch also adds BFD support for IPv6 OSPF. ospf6d will dynamically register/deregister IPv6 neighbors with BFD for monitoring the connectivity of the neighbor. Neighbor is registered with BFD when 2-way adjacency is established and deregistered when adjacency goes down if the BFD is enabled on the interface through which the neighbor was discovered.
OSPF6 BFD command added to configure BFD and parameters (detect multiplier, min rx and min tx).
interface <if-name>
ipv6 ospf6 bfd <detect mult> <min rx> <min tx>
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
Table-id argument support wasnt complete, used the [proto, instance]
combination changes that were done for OSPF multi-instance. In this case
its 'table <table-id>' just like it was 'ospf <instance-id>'
ospf: Fix cli issues with timers throttle spf and no ip ospf authentication...
When entering no timers throttle spf there was no way to specify the delay, hold
time and max hold time so the command was rejected. This is useful for automated
processes that take currently entered cli to remove the cli.
When entering no ip ospf authentication most forms of the command were being
ignored, this fixes that as well.
Signed-off-by: Donald Sharp <sharpd at cumulusnetworks.com>
Reviewed-by:
At the minimum, the OSPF_LSA_SELF logic isnt foolproof, and it may hit assert
in ospf_refresh_unregister_lsa on a router-id change.
Once OSPF has created and flooded LSAs, its not a good idea to change
router-id inline. Tying it to restart has at least two benefits:
- Implementation can remain sane by not having to re-adjust neighbors and LSAs,
based on the new router-id.
- Works as a deterrent for the user to not meddle with the router-id unless
really needed.
is executed, then the init.d/quagga script doesnt wait more than 120 seconds
for the daemon do stop, worse, it goes ahead and starts the new daemon
regardless. This can result into two ospfd processes running on the same config.
Which leads to many issues including but not limited to high cpu usage.
Thats because the two processes are mixing packets on adjancencies thus
causing churn on the box and network.
As long as OSPF is able to reliably send the max-metric router-lsa before
exiting thats mostly good enough for this purpose anyways.
As a solution to this situation, bringing the maximum configurable value of
the on-shutdown timer below the maximum retry to stop a daemon in init.d/quagga
Notes: This may not be an upstreamable patch, still we needed to find
a solution for init.d/quagga and this command this co-exist.
——————————————-------------
- etc/init.d/quagga is modified to support creating separate ospf daemon
process for each instance. Each individual instance is monitored by
watchquagga just like any protocol daemons.(requires initd-mi.patch).
- Vtysh is modified to able to connect to multiple daemons of the same
protocol (supported for OSPF only for now).
- ospfd is modified to remember the Instance-ID that its invoked with. For
the entire life of the process it caters to any command request that
matches that instance-ID (unless its a non instance specific command).
Routes/messages to zebra are tagged with instance-ID.
- zebra route/redistribute mechanisms are modified to work with
[protocol type + instance-id]
- bgpd now has ability to have multiple instance specific redistribution
for a protocol (OSPF only supported/tested for now).
- zlog ability to display instance-id besides the protocol/daemon name.
- Changes in other daemons are to because of the needed integration with
some of the modified APIs/routines. (Didn’t prefer replicating too many
separate instance specific APIs.)
- config/show/debug commands are modified to take instance-id argument
as appropriate.
Guidelines to start using multi-instance ospf
---------------------------------------------
The patch is backward compatible, i.e for any previous way of single ospf
deamon(router ospf <cr>) will continue to work as is, including all the
show commands etc.
To enable multiple instances, do the following:
1. service quagga stop
2. Modify /etc/quagga/daemons to add instance-ids of each desired
instance in the following format:
ospfd=“yes"
ospfd_instances="1,2,3"
assuming you want to enable 3 instances with those instance ids.
3. Create corresponding ospfd config files as ospfd-1.conf, ospfd-2.conf
and ospfd-3.conf.
4. service quagga start/restart
5. Verify that the deamons are started as expected. You should see
ospfd started with -n <instance-id> option.
ps –ef | grep quagga
With that /var/run/quagga/ should have ospfd-<instance-id>.pid and
ospfd-<instance-id>/vty to each instance.
6. vtysh to work with instances as you would with any other deamons.
7. Overall most quagga semantics are the same working with the instance
deamon, like it is for any other daemon.
NOTE:
To safeguard against errors leading to too many processes getting invoked,
a hard limit on number of instance-ids is in place, currently its 5.
Allowed instance-id range is <1-65535>
Once daemons are up, show running from vtysh should show the instance-id
of each daemon as 'router ospf <instance-id>’ (without needing explicit
configuration)
Instance-id can not be changed via vtysh, other router ospf configuration
is allowed as before.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
protocols. BGP and OSPF are integrated to respond this BFD session down message
originated in Zebra via ptmd.
BGP and OSPF now have a bfd command, which tells OSPF/BGP to respond to the
BFD session down message.
OSPF:
interface <>
ip ospf bfd
BGP:
router bgp <>
neighbor <> bfd
Please note that these commands don't enable BFD as a protocol. BFD configuration
and paramter tuning are via BFD applicable UI.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
is able to send out K (=3 by default) packets per thread-write.
Signed-off-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: JR Rivers <jrrivers@cumulusnetworks.com>
Compute and display SPF execution statistics
Detailed SPF statistics, all around time spent executing various pieces of SPF
such as the SPF algorithm itself, installing routes, pruning unreachable networks
etc.
Reason codes for firing up SPF are:
R - Router LSA, N - Network LSA, S - Summary LSA, ABR - ABR status change,
ASBR - ASBR Status Change, AS - ASBR Summary, M - MaxAge
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: JR Rivers <jrrivers@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Quagga sources have inherited a slew of Page Feed (^L, \xC) characters
from ancient history. Among other things, these break patchwork's
XML-RPC API because \xC is not a valid character in XML documents.
Nuke them from high orbit.
Patches can be adapted simply by:
sed -e 's%^L%%' -i filename.patch
(you can type page feeds in some environments with Ctrl-V Ctrl-L)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
OSPFd only allocates some stub information for loopback interfaces.
This causes a crash when the interface state machine is started on
that interface by configuring a different network type.
It doesn't make much sense to configure the network type of a loopback
interface, therefore, just forbid it.
See also bugzilla #670.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Use the new keyword command style for:
- default-information originate
- distance ospf
- redistribute
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Fixup some DEFUNS with incorrect command strings or mixed up helpstrings.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
A set of patches to clarify some comments as well as cleanup code that was
causing warnings. After these patches, the code can be compiled with
-Wall -Wsign-compare -Wpointer-arith -Wbad-function-cast -Wwrite-strings
-Wmissing-prototypes -Wmissing-declarations -Wchar-subscripts -Wcast-qual
-Wextra -Wno-unused-parameter -Wno-missing-field-initializers
(what is current in trunk plus -Wextra -Wno-unused-parameter
-Wno-missing-field-initializers).
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Use the correct argument for the protocol lookup in
ospf distribute-list commands.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Store the MaxAge LSA list in a tree instead of a linked list for efficient access.
Walking the list can be quite inefficient in some large systems and under certain tests.
ospfd maintains the list of LSA's that have been MaxAge'd out in a separate
linked list for removal by a remover/walker thread. When a new LSA is to be
installed, the old LSA is ejected and when it is ejected, the MaxAge LSA list
is traversed to ensure that the old LSA is also removed from this list if it
exists on this list.
When a large number (> 5K) MaxAge LSAs are bombarding the system, walking this
list takes a significant time causing timers to fire and actions to be taken
such as expiring neighbors due to expiry of DeadInterval (especially when timer
is really low, <= 12s), creating a spiral of instability.
By making this MaxAge LSA list be a tree, this problem is mitigated.
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
In the event areas are created at a later point of time with respect
to the playback of the "max-metric router-lsa administrative" command,
those areas do not get into indefinite max-metric mode. This patch is
inteneded to store the configuration and apply it to all future areas
that may be created.
In the process, some other bugs that were there with respect to restart
etc are fixed up.
Tested locally to see that the fix works across multiple
areas and across multiple restarts.
Signed-off-by: Ayan Banerjee <ayan@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@cumulusnetworks.com>
Reviewed-by: JR Rivers <jrrivers@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@cumulusnetworks.com>
this replaces most occurences of routing protocol lists by preprocessor
defines from route_types.h. the latter is autogenerated from
route_types.txt by a perl script (previously awk). adding a routing
protocol now is mostly a matter of changing route_types.txt and log.c.
Conflicts:
lib/route_types.awk
* (general) Get rid of the router and network LSA specific refresh timers
and make the general refresher do this instead. Get rid of the twiddling
of timers for router/network LSA that was spread across the code.
This lays the foundations for future, general LSA refresh improvements,
such as making sequence rollover work, and having generic LSA delays.
* ospfd.h: (struct ospf) Bye bye to the router-lsa update timer thread
pointer.
(struct ospf_area) and to the router-lsa refresh timer.
* ospf_interface.h: Remove the network_lsa_self timer thread pointer
* ospf_lsa.h: (struct ospf_lsa) oi field should always be there, for benefit
of type-2/network LSA processing.
(ospf_{router,network}_lsa_{update_timer,timer_add}) no timers for these
more
(ospf_{router,network}_lsa_update) more generic functions to indicate that some
router/network LSAs need updating
(ospf_router_lsa_update_area) update router lsa in a particular area alone.
(ospf_{summary,summary_asbr,network}_lsa_refresh) replaced by the general
ospf_lsa_refresh function.
(ospf_lsa_refresh) general LSA refresh function
* ospf_interface.h: (struct ospf_if_params) add field for saved network LSA
seqnum
* ospf_interfa.c: (ospf_new_if_params) init network_lsa_seqnum field to
initial seqnum - doesnt matter though.
* ospf_lsa.c: (ospf_network_lsa_new) check for any saved sequence number,
and use if it exists. Save the result back. This should help avoid needless
round of LSUpdate/LSRequests when a neighbour has to tell the originator
"uhm, i have something newer than that already".
* ospf_vty.c: (show_ip_ospf_interface_sub) Show the saved network LSA seqnum
The following syntax forms were not historically supported
by Quagga, although IOS accepted them w/o a problem:
no ip ospf cost <1-65535>
no ospf cost <1-65535>
no ip ospf cost <1-65535> A.B.C.D
no ospf cost <1-65535> A.B.C.D
From now on Quagga also supports these variants.
* global: In struct ospf_path, change struct ospf_interface *oi to int
ifindex. It is unsafe to reference *oi as an ospf interface can be
deleted under your feet. Use a weak reference instead.
2008-08-15 Paul Jakma <paul.jakma@sun.com>
* */*: Fix various problems flagged by Sun Studio compiler.
- '<qualifier> <storage>' obsolescent in declarations
- empty statements (';' after ALIAS definitions)
- implicit declarations (e.g printstack in lib/log.c)
- "\%" in printf string instead of "%%"
- loops that return on the first iteration (legitimately, but
compiler can't really know), e.g. bgp_routemap.c
- internal declarations which mask prototypes.
