Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-8122
per draft-ietf-idr-ix-bgp-route-server-09:
2.3.2.2.2. BGP ADD-PATH Approach
The [I-D.ietf-idr-add-paths] Internet draft proposes a different
approach to multiple path propagation, by allowing a BGP speaker to
forward multiple paths for the same prefix on a single BGP session.
As [RFC4271] specifies that a BGP listener must implement an implicit
withdraw when it receives an UPDATE message for a prefix which
already exists in its Adj-RIB-In, this approach requires explicit
support for the feature both on the route server and on its clients.
If the ADD-PATH capability is negotiated bidirectionally between the
route server and a route server client, and the route server client
propagates multiple paths for the same prefix to the route server,
then this could potentially cause the propagation of inactive,
invalid or suboptimal paths to the route server, thereby causing loss
of reachability to other route server clients. For this reason, ADD-
PATH implementations on a route server should enforce send-only mode
with the route server clients, which would result in negotiating
receive-only mode from the client to the route server.
This allows us to delete all of the following code:
- All XXXX_rsclient() functions
- peer->rib
- BGP_TABLE_MAIN and BGP_TABLE_RSCLIENT
- RMAP_IMPORT and RMAP_EXPORT
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com
Ticket: CM-8014
This implements addpath TX with the first feature to use it
being "neighbor x.x.x.x addpath-tx-all-paths".
One change to show output is 'show ip bgp x.x.x.x'. If no addpath-tx
features are configured for any peers then everything looks the same
as it is today in that "Advertised to" is at the top and refers to
which peers the bestpath was advertise to.
root@superm-redxp-05[quagga-stash5]# vtysh -c 'show ip bgp 1.1.1.1'
BGP routing table entry for 1.1.1.1/32
Paths: (6 available, best #6, table Default-IP-Routing-Table)
Advertised to non peer-group peers:
r1(10.0.0.1) r2(10.0.0.2) r3(10.0.0.3) r4(10.0.0.4) r5(10.0.0.5) r6(10.0.0.6) r8(10.0.0.8)
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r2(10.0.0.2) (10.0.0.2)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 8
Last update: Fri Oct 30 18:26:44 2015
[snip]
but once you enable an addpath feature we must display "Advertised to" on a path-by-path basis:
superm-redxp-05# show ip bgp 1.1.1.1/32
BGP routing table entry for 1.1.1.1/32
Paths: (6 available, best #6, table Default-IP-Routing-Table)
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r2(10.0.0.2) (10.0.0.2)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 8
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:44 2015
Local, (Received from a RR-client)
34.34.34.34 (metric 20) from r3(10.0.0.3) (10.0.0.3)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 7
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
56.56.56.56 (metric 20) from r6(10.0.0.6) (10.0.0.6)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 6
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
56.56.56.56 (metric 20) from r5(10.0.0.5) (10.0.0.5)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 5
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
34.34.34.34 (metric 20) from r4(10.0.0.4) (10.0.0.4)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 4
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r1(10.0.0.1) (10.0.0.1)
Origin IGP, metric 0, localpref 100, valid, internal, best
AddPath ID: RX 0, TX 3
Advertised to: r1(10.0.0.1) r2(10.0.0.2) r3(10.0.0.3) r4(10.0.0.4) r5(10.0.0.5) r6(10.0.0.6) r8(10.0.0.8)
Last update: Fri Oct 30 18:26:34 2015
superm-redxp-05#
Ticket: CM-7861
Reviewed by: CCR-3651
Testing: See bug
bgp is using both bm->master and master pointers interchangebly
for thread manipulation. Since they are the same thing consolidate
to one pointer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-7593
Reviewed By: CCR-3563
Testing Done: Manual verification of failed scenario (2.5-br)
When BGP receives an update to a redistributed route and the type of
the source has changed (e.g., from OSPF to static), the source route
type is not being updated in the RIB entry. This can lead to problems
such as the route being incorrectly deleted if redistribution for the
prior source is unconfigured.
Fix the code to update the source route type.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vipin Kumar <vipin@cumulusnetworks.com>
As part of the debian build process for jessie we are seeing
some compile issues. This addresses these issues
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
bgp is using both bm->master and master pointers interchangebly
for thread manipulation. Since they are the same thing consolidate
to one pointer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
is empty
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-7475
Reviewed By: Donald Sharp
Testing Done:
If the BGP table is empty, intead of returning
{'alert': 'No BGP network exists', 'routerId': '10.0.9.2',
'tableVersion': 180}
we should return
{'routerId': '10.0.9.2', 'routes': {}, 'tableVersion': 180}
This provides a more consistent json interface which is easier to script
against.
This patch adds a hostname capability. The node's hostname and
domainname are exchanged in the new capability and used in show command
outputs based on a knob enabled by the user. The hostname and domainname
can be a maximum of 64 chars long, each.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com>
Ticket: CM-5660
Reviewed By: CCR-2563
Testing Done:
Ticket: CM-4109
Reviewed-by: CCR-3414
Testing: See bug
Fixup of these memory issues:
(A) peer->clear_node_queue was accidently removed. Add back in.
(B) Clean up bm->process_main_queue and bm->process_rsclient_queue initialization
(C) Some memory leaks
(D) Clean up unused threads
Ticket: CM-7177
Reviewed-by: CCR-3396
Testing: See bug
This code change does several small things:
(A) Fix a couple detected memory leaks
(B) Fix all malloc operations to use the correct XMALLOC operation in bgpd and parts of lib
(C) Adds a few new memory types to make it easier to detect issues
Ticket: CM-6789
Reviewed By: CCR-3263
Testing Done: Manual Testing and smoke tests
Whenever some sort of output is encountered, added a json version with
proper logic as well.
Ticket : CM-7047
Reviewed by : CCR-3321
Testing : Trivial
In function bgp_aggregate_add, variables 'aspath' and 'community' are
malloced but not guaranteed to be freed before the function returns.
BGP: Display Link local addr and ifname as part of 5549 support
As part of BGP unnumbered and RFC 5549 support, the implementation will honor the
link local address as the NH if present and so it'd be useful to display that
info along with the interface name, when displaying the BGP route summary. That
is what this patch aims to do.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
"bgp confederation id X" are the same value.
router bgp 1
bgp router-id 10.1.1.1
bgp confederation identifier 1
bgp confederation peers 24 35
neighbor 10.1.1.2 remote-as 24
neighbor 10.1.1.2 update-source lo
neighbor 10.1.1.3 remote-as 1
neighbor 10.1.1.3 update-source lo
The customer does this because they want to peer to 10.1.1.2 as a
confed-external peer but peer with 10.1.1.3 as a normal iBGP peer.
The bug was that we thought 10.1.1.3 was an EBGP peer so we did not send him
LOCALPREF which caused the Juniper to send us a NOTIFICATION. I confirmed
that quagga also sends a NOTIFICATION in this scenario.
The fix is to add a check to see if router bgp X and bgp confederation
identifier X are equal because that is a factor in determining if a peer is
EBGP or IBGP
Additional issues fixed in the this patch:
We were not properly removing all AS_CONFED_SEQUENCEs/SETs from the aspath
when advertising a route to an ebgp peer. This was due to two issues:
We only called aspath_delete_confed_seq() if confederations were
configured. We can RX as aspath with CONFED segments even if
confederations are not configured.
aspath_delete_confed_seq() was implemented based on the original confed
RFC 3065 which basically said "remove all of the leading
AS_CONFED_SEQUENCEs/SETs" where the new confed RFC 5065 says "remove ALL
of the AS_CONFED_SEQUENCEs/SETs"
peer-groups did not work for confed-external peers. peer_calc_sort() always
returned BGP_PEER_EBGP for a confederations where the remote-as was not
specified. The reason was the peer->as_type was AS_UNSPECIFIED but we checked
if (peer->as_type != AS_SPECIFIED)
return (peer->as_type == AS_INTERNAL ? BGP_PEER_IBGP : BGP_PEER_EBGP);
After fixing that I found that when we got to the else where we checked for
peer1 we could only possibly return BGP_PEER_IBGP or BGP_PEER_EBGP, we need
to also be able to return BGP_PEER_CONFED. I changed this to return
peer1->sort.
"show ip bgp x.x.x.x" would always display "Local" for the aspath. This is
because we were calling aspath_counts_hop() to determine if the aspath was
empty. This is wrong though because CONFED segments do not count towards
aspath hopcount. The fix is to null check aspath->segments to determine if
the aspath is actually empty.
"show ip bgp x.x.x.x" and "show ip bgp neighbor" always displayed
"internal" or "external" and never "confed-internal" or "confed-external".
This made troubleshooting difficult because I couldn't tell exactly what
kind of peer I was dealing with. I added the confed-internal and
confed-external output...also added a "peer-type" field in the json output
for 'show ip bgp x.x.x.x'
"show ip bgp peer-group" did not list the peer-group name if we hadn't
determined the "type" (internal, external, etc) for the peer-group
an implicit withdraw as is done for the NEXT_HOP attribute in the
update itself.
Note: Check is implemented only for IPv6 for the global nexthop. The
code will quietly ignore an invalid IPv6 link-local nexthop, if present;
this is the existing behavior and is not changed.
Signed-off-by: Vivek Venkataraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
honored correctly for EBGP peers after the introduction of the
dynamic update groups functionality. Ensure this is handled
correctly. Also, the route-map can separately set different
nexthops - IPv4, IPv6 global or IPv6 link-local; treat these
separately.
This adds support for BGP RFC 5549 (Extended Next Hop Encoding capability)
* send and receive of the capability
* processing of IPv4->IPv6 next-hops
* for resolving these IPv6 next-hops, itsworks with the current
next-hop-tracking support
* added a new message type between BGP and Zebra for such route
install/uninstall
* zserv side of changes to process IPv4 prefix ->IPv6 next-hops
* required show command changes for IPv4 prefix having IPv6 next-hops
Few points to note about the implementation:
* It does an implicit next-hop-self when a [IPv4 prefix -> IPv6 LL next-hop]
is to be considered for advertisement to IPv4 peering (or IPv6 peering
without Extended next-hop capability negotiated)
* Currently feature is off by default, enable it by configuring
'neighbor <> capability extended-nexthop'
* Current support is for IPv4 Unicast prefixes only.
IMPORTANT NOTE:
This patch alone isn't enough to have IPv4->IPv6 routes installed into
the kernel. A separate patch is needed for that to work for the netlink
interface.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Vivek Venkatraman <vivek@cumulusnetworks.com>
Donald Sharp <sharpd@cumulusnetworks.com>
Our code implemented 'force' for a keyword while quagga mainline implemented 'all'.
This fixups the #define usage that was missed that came in during one of the patch
files. This is a compile only testing
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
bgpd: Exchange hostname capability and display hostnames in outputs
This patch adds a hostname capability. The node's hostname and
domainname are exchanged in the new capability and used in show command
outputs based on a knob enabled by the user. The hostname and domainname
can be a maximum of 64 chars long, each.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com>
BGP: Fix network import check use with NHT instead of scanner
When next hop tracking was implemented and the bgp scanner was eliminated,
the "network import-check" command got broken. This patch fixes that
issue. NHT is used to not just track nexthops, but also the static routes
that are announced as part of BGP's network command. The routes are
registered only when import-check is enabled. To optimize performance,
we register static routes only when import-check is enabled.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
state to facilitate clearing of the routes received from the peer - remove
from the RIB, reselect best path, update/delete from Zebra and to other
peers etc. At the end of this, a Clearing_Completed event is generated to
the FSM which will allow the peer to move out of Clearing to Idle.
The issue in the code is that there is a possibility of multiple Clearing
Completed events being generated for a peer, one per AFI/SAFI. Upon the
first such event, the peer would move to Idle. If other events happened
(e.g., new connection got established) before the last Clearing_Completed
event is received, bad things can happen.
Fix to ensure only one Clearing_Completed event is generated.
When a route is announced in BGP via "network" command, we also register its
next hop with NHT code to allow of updates when the nexthop changes. When this
route is deleted via "no network" command, we incorrectly make a second call to
unregister the NHT tracking associated with this route. This causes a crash.
Fix that.
