Add a switchover test that consists in clearing the rt2 neighbor on rt1.
Check that the switchover between primary and backup happens before the
SPF re-computation.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add a switchover test that consists in:
- Setting no link-detect on rt1 eth-rt2 so that zebra does not take
account linkdown events on this interface.
- Shutting down rt1 eth-rt2 from the switch side
- Wait for the hello timer expiration
Check that the switchover between primary and backup happens before the
SPF re-computation.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add a switchover test that consists in shutting down an interface.
Check that the switchover between primary and backup happens before the
SPF re-computation.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
If ISIS is running on an IPv6 only topology, the command "spf interval"
has no effect.
Only the IPv4 SPF tree timers are taken into account.
Base the next SPF scheduling on the last running SPF tree.
Fixes: be985ba059 ("isisd: make use of advanced concepts like arrays and loops")
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add a switchover test that consists in:
- Setting up ISIS BFD between rt5 and rt6
- Setting no link-detect on rt6 eth-rt5 so that zebra does not take
account linkdown events on this interface.
- Shutting down rt6 eth-rt5 from the switch side
Check that the switchover between primary and backup happens before the
SPF re-computation.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Add a switchover test that consists in shutting down an interface.
Check that the switchover between primary and backup happens before the
SPF re-computation.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
isis_ifp_down() may in some circumstances be called twice on a down
interface event.
Avoid applying fast-reroute on an already down interface.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
When an IS-IS interface is coming down, fast-reroute may be triggered
twice: a first time after the detection of the interface down event and
a second time after the detection of the adjacency down (because of the
expiration of the ISIS Hello or BFD timers).
Avoid a BFD down event from running fast-reroute another time if the
interface was already detected down.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Backup routes are sent to zebra by routing daemons such as isisd so that
the dataplane can pre-install them with a lower priority. When an
interface comes down, the associated primary routes are discarded by the
dataplane and the backup ones take over.
However, some dataplanes (e.g. Netlink ones) do not pre-install the
backup routes. Associated prefixes have no next-hop until SPF is
recomputed.
Apply fast-reroute as soon as an interface falls down by sending route
UPDATEs to zebra.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Allow the nexthoplookup function to return the first nexthop found on
ifindex interface if the IP is unspecified.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
When a adjacency falls down, the primary routes are not deleted on the
dataplane until the SPF is recomputed. Even the backup routes are
pre-installed on the dataplane, there is no fast-route optimization.
Reasons for an adjacency to come down are:
- BFD down
- Hello timer timeout
- User adjacency clear
Apply the backup route switchover for fast-reroute as soon an IS-IS
adjacency falls down before the first SPF re-computation. Pre-computed
backup routes are applied sooner.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
If a end users does something like this:
int enp39s0
ipv6 ospf6 hello-interval 65535
And then the timer pops and we send the hello and immediately
if the end user does this:
ipv6 ospf6 hello-interval 5
The timer is not being reset and FRR waits the full 65k seconds
before sending the hello again, which then immediately sets
the next hello to go out in 5 seconds.
When FRR receives the new timer value, look at how much time
is left on the timer in seconds. If this value is greater
than the new hello timer, stop the timer and set it too that
value.
This should fix a CI system test failure found, where the
system is testing setting timer from things like 12 seconds
to 65k seconds then back down to 12 and that the ospf6 neighbor
relationship stays up.
The code was also changed from thread_add_event to thread_add_timer
in all cases. I am not sure what would happen if a show command
comes in for a thread timer remaining with an event instead of a timer
just make it consistent.
This was chased down because the support bundle showed this:
r0# show ipv6 ospf6 vrf all interface
r0-r1-eth0 is up, type BROADCAST
Interface ID: 6
Internet Address:
inet6: fe80::a4ea:d3ff:fe35:cef1/64
inet6: fd00::1/64
Instance ID 0, Interface MTU 1500 (autodetect: 1500)
MTU mismatch detection: enabled
Area ID 0.0.0.0, Cost 10
State DR, Transmit Delay 1 sec, Priority 1
Timer intervals configured:
Hello 12(65480.960), Dead 48, Retransmit 5
And looking at the test code is doing stuff like this:
2022/05/16 17:08:15 OSPF6: [M7Q4P-46WDR] vty[5]@(config)# interface r1-r0-eth0
2022/05/16 17:08:15 OSPF6: [M7Q4P-46WDR] vty[5]@(config-if)# ipv6 ospf6 hello-interval 65535
2022/05/16 17:08:15 OSPF6: [M7Q4P-46WDR] vty[5]@(config-if)# no ipv6 ospf6 hello-interval
2022/05/16 17:08:16 OSPF6: [M7Q4P-46WDR] vty[5]@(config-if)# ipv6 ospf6 hello-interval 1
2022/05/16 17:08:16 OSPF6: [M7Q4P-46WDR] vty[5]@(config-if)# ipv6 ospf6 hello-interval 12
If the old timer value pops, the hello interval is set to 65k and never reset again.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When running `show ipv6 ospf6 interface` the hello timer period
is shown, but there is no indication on how much time is left
on the timer. Add a clue:
sharpd@eva ~/frr5 (master)> vtysh -c "show ipv6 ospf6 int"
enp39s0 is up, type BROADCAST
Interface ID: 2
Internet Address:
inet : 192.168.119.224/24
inet6: 2603:6080:602:509e:9a14:998:b154:9e9/64
Instance ID 0, Interface MTU 1500 (autodetect: 1500)
MTU mismatch detection: enabled
Area ID 0.0.0.0, Cost 1000
State DR, Transmit Delay 1 sec, Priority 1
Timer intervals configured:
Hello 10(2.652), Dead 40, Retransmit 5
DR: 192.168.122.1 BDR: 0.0.0.0
Number of I/F scoped LSAs is 1
0 Pending LSAs for LSUpdate in Time 00:00:00 [thread off]
0 Pending LSAs for LSAck in Time 00:00:00 [thread off]
Authentication Trailer is disabled
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The global vrf in zebra is always non-NULL. In general, it is bound to
default vrf by `zebra_vrf_init()`, at other times bound to some specific
vrf. Anyway, non-NULL.
So remove all redundant checkings for the returned value of
`zebra_vrf_get_evpn()`.
Additionally, remove the unnecessary check for `zvrf` in
`zebra_vxlan_cleanup_tables()`.
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Allow BGP to control the TOS DSCP value in the tcp header
via a new command at the bgp global level `bgp session-dscp <0-63>`
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Signed-off-by: Pavel Shirhov <pavelsh@microsoft.com>
The creation of the update group is a tiny bit of a black box and is hard
to figure out by hand if it is correct. Add a bit of code so that FRR
operators/developers can determine if the update group categorization
makes us happy.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Several functions in bgp_debug.[ch] take a const struct peer *
and also return a bool instead of an int.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Fix the no forms of some rpki commands to take variable
values on the no form. So that people cut-n-pasting while
adding a no works.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
