When a BGP instance including the default instance is deleted, it needs to be
unlinked from the corresponding VRF structure. However, instance deletion does
not happen in one shot but needs a lot of threads to run - peer event handling,
route processing etc. - before it can complete. Premature unlinking of the
instance from underlying VRF would result in BGP routes not being deleted from
the zebra RIB.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-10930
Reviewed By: CCR-4717
Testing Done: Manual, bgp-smoke
Instead of turning on IPv6 RA on every interface as soon as it has an IPv6
address, only enable it upon configuration of BGP neighbor. When the BGP
neighbor is deleted, signal that RAs can be turned off.
To support this, introduce new message interaction between BGP and Zebra.
Also, take appropriate actions in BGP upon interface add/del since the
unnumbered neighbor could exist prior to interface creation etc.
Only unnumbered IPv6 neighbors require RA, the /30 or /31 based neighbors
don't. However, to keep the interaction simple and not have to deal with
too many dynamic conditions (e.g., address deletes or neighbor change to/from
'v6only'), RAs on the interface are triggered upon any unnumbered neighbor
configuration.
BGP-triggered RAs will cause RAs to be initiated on the interface; however,
if BGP asks that RAs be stopped (upon delete of unnumbered neighbor), RAs
will continue to be exchanged if the operator has explicitly enabled.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-10640
Reviewed By: CCR-4589
Testing Done: Various manual and automated (refer to defect)
With the addition of RA being turned on by default.
Spewing this error message when unable to connect
doesn't make much sense anymore.
Ticket: CM-10494
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Modified the configuration code to properly allow a peer-group member
to have a route-map out applied when one does not exist on the peer-group
itself. This capability already existed for route-map in.
Ticket: CM-10058
Signed-off-by: Don Slice
Reviewed-by: Donald Sharp
Quagga BGP needed a config 'bgp multiple-instance' in order to be able
to configure and use VRFs. Since this support is intrinsic to the
implementation, make this configuration on by default. Corresponding
change to 'show running-config' (and write) to display only if "no" is
configured.
This change will eliminate one unnecessary step in the configuration.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-10070
Reviewed By: CCR-4383
Testing Done: Manual
When displaying the output of a 'show run',
display the neighbor information in an ordered
manner.
Ticket: CM-10184
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
When creating a 'struct peer' add in the ability to set the peer group
associated with that peer.
Ticket: CM-10184
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Upon receipt of incoming connection, a peer structure (doppelganger) is
created internally and the connection processed for it. The problem is
that in the case of BGP unnumbered, the sockunion structure within BGP was
being updated (in peer_create()) prior to the peer's flags being updated,
so it didn't take into account the 'v6only' configuration. This results
in subsequent problems when bgp_bind() is done - the socket ends up being
bound to the BGP instance instead of the interface.
In the case of an incoming connection, we should just use the addresses
on which the connection was setup/accepted, there is no need to attempt to
derive it again. Further, there is no need to attempt to update addresses
at the time of peer_create() since that is done when the connection is
attempted in bgp_start().
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-10028
Reviewed By: CCR-4373
Testing Done: Manual, bgpsmoke
Updates to routemaps and delete of the routemap were not working properly
for VRFs. This was because while routemaps are global, the routemap update
processing timer and the processing were at the per-instance level. This
approach was unable to handle processing for multiple instances as the
routemap has no tracking of which instances are still pending processing.
This lead to the processing happening correctly only for the first instance
- which could be the default instance or some other instance. It could also
result in reference to freed memory for an instance.
The fix done is to make the update/delete processing also global and not per
instance. This means that the route-map delay timer will be global and a global
thread will handle the change (or delete) for all instances instead of spawning
a separate thread for each instance. To support this, a global BGP command
"bgp route-map delay-timer <value>" has been implemented. The existing command
per-instance is not deleted but will update the global timer.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-6970, CM-9918
Reviewed By: CCR-4320
Testing Done: Manual, bgpsmoke
Code changes to make unnumbered peering work in a VRF. The changes have
to do with locating the interface in the correct VRF (in order to look for
neighbor address) in the case of outgoing connections and when specifying
source address as well as fetching the correct instance for an incoming
connection based on reading the device the socket is bound to (the multi-vrf
socket option in the kernel).
Additionally, for IPv4 unnumbered peering in a VRF (based on /30 or /31
addresses), bind to the VRF rather than the interface.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9311
Reviewed By: CCR-4192
Testing Done: Manual, bgpsmoke
The BGP instance cleanup was deleting interfaces in that instance after
prior fixes, but this ended up deleting the interface list header which
was not being re-created. Added code to re-create this at the time an
instance is created.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Ticket: CM-9466
Reviewed By: CCR-4164
Testing Done: Manual and verified failed test
Perform interface cleanup as an instance is deleted. This takes care of the
scenario when BGP exits (or is stopped/restarted) too as instances undergo
deletion and the interface cleanup is done as the last step in that.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Fixes: 46abd3e3e6
Ticket: CM-9410
Reviewed By: CCR-4143
Testing Done: Reran failed test
Link BGP instance (Default or VRF) to the corresponding VRF structure and
modify lookup to use this. The logic is very similar to what is implemented
in zebra - the 'struct zebra_vrf' there is essentially 'struct bgp' in BGP.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9122
Reviewed By: CCR-4102
Testing Done: Manual
With VRF support, certain objects are now maintained per BGP instance. At
exit, the list of BGP instances has to be freed only after processing the
per-instance objects.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Fixes: ad4cbda1a3
Ticket: CM-9340
Reviewed By:
Testing Done:
Various changes and fixes related to VRF registration, deletion,
BGP exit etc.
- Define instance type
- Ensure proper handling upon instance create, delete and
VRF add/delete from zebra
- Cleanup upon bgp_exit()
- Ensure messages are not sent to zebra for unknown VRFs
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9128, CM-7203
Reviewed By: CCR-4098
Testing Done: Manual
When a BGP instance is deleted through 'no router bgp', the required
cleanup was not being performed. This is after VRF-related changes.
Fix to ensure this is taken care of.
Note: Further changes needed in this area for VRFs.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-9597
Reviewed By: CCR-4097
Testing Done: Verified failed test
While processing references to the macro PEERAF_FOREACH(), aggressive loop
optimization by gcc 4.9.x (probably 4.8 and greater) was resulting in the
generated code not checking on the index as well as eliminating some code.
This was leading to a dereference of invalid memory when a BGP peer came up.
The fix is to scrap this convoluted macro. Two other changes done are to
eliminate overloading of "afindex" and make the loop iterator an integer.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Dave Olson <olson@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Ticket: CM-8889
Reviewed By: CCR-4018
Testing Done: Verified failure scenario
Note: This code was added as part of update-groups implementation; when
upstreaming update-groups, this patch should also be included.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-8788
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-8472
The first as-path is what the original as-path for the test, the second
is what the as-path should look like once all confed SETs and SEQs have
been removed. At the time the test was written quagga did not correctly
remove confed SETs and SEQs but whoever wrote the test didn't notice
this and assumed that the behavior they were seeing was correct so used
that output to populate the second as-path.
Now that we do correctly remove the confed parts these tests fail. So
the fix is to update the second as-path for these two tests so that they
no longer contain any confed SETs/SEQs.
BGP uses a second #define that is equal to MULTIPATH_NUM. There
is no point in having a different #define. Just consolidate.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
configuration
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Ticket: CM-8321
This allows the user to configure the peer-group as an option for the
"neighbor swpX interface" command.
{code}
!
router bgp 100
neighbor FOO peer-group
neighbor FOO remote-as external
neighbor swp1 interface
neighbor swp2 interface v6only
neighbor swp3 interface peer-group FOO
neighbor swp4 interface v6only peer-group FOO
!
address-family ipv4 unicast
neighbor FOO activate
neighbor swp1 activate
neighbor swp2 activate
exit-address-family
!
{code}
Note that if the user configures
{code}
neighbor swp5 interface
neighbor swp5 peer-group FOO
{code}
We will display that as "neighbor swp5 interface peer-group FOO". It
did not seem worth tracking that the peer-group was entered via two
lines instead of one.
During CR for nexthop upstream it was noticed that usage
of prefix2str was not consistent. This fixes this problem
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
BGP is currently displaying the in-use router-id in the config. This is
conditional on a CONFIG flag, however, that flag is set even when there
is no configured router-id and the router-id learnt from Zebra is in-use.
The CONFIG flag for router-id is redundant since there is a separate
variable for the configured value, so use that and deprecate the CONFIG
flag. This also makes BGP behave like OSPF.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Ticket: CM-8077, CM-8220
Reviewed By: CCR-3793
Testing Done: Manual verification (in 2.5-br)
Note: Imported from 2.5-br patch bgpd-fix-router-id-config-display.patch
Modify code to recognize that we are not actually reseting the
neighbor if the user actually enters a remote-as of external->external
for a neighbor.
Ticket: CM-8100
Reviewed-by: CCR-3783
Testing: See bug
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-8122
per draft-ietf-idr-ix-bgp-route-server-09:
2.3.2.2.2. BGP ADD-PATH Approach
The [I-D.ietf-idr-add-paths] Internet draft proposes a different
approach to multiple path propagation, by allowing a BGP speaker to
forward multiple paths for the same prefix on a single BGP session.
As [RFC4271] specifies that a BGP listener must implement an implicit
withdraw when it receives an UPDATE message for a prefix which
already exists in its Adj-RIB-In, this approach requires explicit
support for the feature both on the route server and on its clients.
If the ADD-PATH capability is negotiated bidirectionally between the
route server and a route server client, and the route server client
propagates multiple paths for the same prefix to the route server,
then this could potentially cause the propagation of inactive,
invalid or suboptimal paths to the route server, thereby causing loss
of reachability to other route server clients. For this reason, ADD-
PATH implementations on a route server should enforce send-only mode
with the route server clients, which would result in negotiating
receive-only mode from the client to the route server.
This allows us to delete all of the following code:
- All XXXX_rsclient() functions
- peer->rib
- BGP_TABLE_MAIN and BGP_TABLE_RSCLIENT
- RMAP_IMPORT and RMAP_EXPORT
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com
Ticket: CM-8014
This implements addpath TX with the first feature to use it
being "neighbor x.x.x.x addpath-tx-all-paths".
One change to show output is 'show ip bgp x.x.x.x'. If no addpath-tx
features are configured for any peers then everything looks the same
as it is today in that "Advertised to" is at the top and refers to
which peers the bestpath was advertise to.
root@superm-redxp-05[quagga-stash5]# vtysh -c 'show ip bgp 1.1.1.1'
BGP routing table entry for 1.1.1.1/32
Paths: (6 available, best #6, table Default-IP-Routing-Table)
Advertised to non peer-group peers:
r1(10.0.0.1) r2(10.0.0.2) r3(10.0.0.3) r4(10.0.0.4) r5(10.0.0.5) r6(10.0.0.6) r8(10.0.0.8)
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r2(10.0.0.2) (10.0.0.2)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 8
Last update: Fri Oct 30 18:26:44 2015
[snip]
but once you enable an addpath feature we must display "Advertised to" on a path-by-path basis:
superm-redxp-05# show ip bgp 1.1.1.1/32
BGP routing table entry for 1.1.1.1/32
Paths: (6 available, best #6, table Default-IP-Routing-Table)
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r2(10.0.0.2) (10.0.0.2)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 8
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:44 2015
Local, (Received from a RR-client)
34.34.34.34 (metric 20) from r3(10.0.0.3) (10.0.0.3)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 7
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
56.56.56.56 (metric 20) from r6(10.0.0.6) (10.0.0.6)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 6
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
56.56.56.56 (metric 20) from r5(10.0.0.5) (10.0.0.5)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 5
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
34.34.34.34 (metric 20) from r4(10.0.0.4) (10.0.0.4)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 4
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r1(10.0.0.1) (10.0.0.1)
Origin IGP, metric 0, localpref 100, valid, internal, best
AddPath ID: RX 0, TX 3
Advertised to: r1(10.0.0.1) r2(10.0.0.2) r3(10.0.0.3) r4(10.0.0.4) r5(10.0.0.5) r6(10.0.0.6) r8(10.0.0.8)
Last update: Fri Oct 30 18:26:34 2015
superm-redxp-05#
BGP ORF prefix lists are in a separate namespace; this was previously
hooked up with a special-purpose AFI value. This is a little kludgy for
extension, hence this splits it off.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
These are about to be touched and there's no point in other code
touching into prefix list's internas. Add some isolation.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-7926
There was a crash from not NULLing out peer->hostname but I cleaned
up a bunch of other suspect ones as well.
very easy to blackhole routes.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-6649
Ticket: CM-7861
Reviewed by: CCR-3651
Testing: See bug
bgp is using both bm->master and master pointers interchangebly
for thread manipulation. Since they are the same thing consolidate
to one pointer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-7737
Reviewed-by: CCR-3611
Testing: See bug
When configuring a bgp peer that already has some config hung off of it,
such as 'interface v6only' and then configuring remote-as internal/external
will not cause the config to be taken.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
As part of the debian build process for jessie we are seeing
some compile issues. This addresses these issues
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
bgp is using both bm->master and master pointers interchangebly
for thread manipulation. Since they are the same thing consolidate
to one pointer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
zclient.c depended upon link time inclusion of a
extern struct thread_master *master. This is a violation of the
namespace of the calling daemon. If a library needs the pointer
pass it in and save it for future use.
This code change also makes the zclient code consistent with
the other lib functions that need to schedule work on your behalf
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This patch adds a hostname capability. The node's hostname and
domainname are exchanged in the new capability and used in show command
outputs based on a knob enabled by the user. The hostname and domainname
can be a maximum of 64 chars long, each.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com>
Ticket: CM-5660
Reviewed By: CCR-2563
Testing Done:
Ticket: CM-7012
Reviwed by: CCR-3451
Testing: See bug
When you specify a neighbor <interface> <something>
and don't specify a remote-as the neighbor relationship
will still come up with ipv6 unnumbered if you have
RA configured on the interface.
Ticket: CM-4109
Reviewed-by: CCR-3414
Testing: See bug
Fixup of these memory issues:
(A) peer->clear_node_queue was accidently removed. Add back in.
(B) Clean up bm->process_main_queue and bm->process_rsclient_queue initialization
(C) Some memory leaks
(D) Clean up unused threads
Ticket: CM-6369
Reviewed By: CCR-3318
Testing Done: Manual testing of various password scenarios.
This is a port of patch bgpd-unnumbered-nbr-fix-password.patch from
2.5-br.
In the case of BGP unnumbered, the peer IP address is derived and not
explicitly configured. If there is a password configured for the peer,
it can be set on the listen socket only after the IP address has been
derived and needs to be cleared when the IP address goes away.
Ticket: CM-6517
Reviewed By: Trivial
Testing Done: Manual testing in 2.5-br
This commit is a port of the patch bgpd-dynamic-nbr-fix-config-error.patch
from 2.5-br.
Ticket: CM-6192
Reviewed By: Donald, Daniel, Vipin
Testing Done:
In the presence of an IPv4 address that is not a /30 or /31 and the user
is trying to use BGP unnumbered, a warning message is printed which
seems confusing to the user. Fixing the warning message to indicate that
its only a v4 session isn't coming up makes it clearer.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
Acked-by: Daniel Walton <dwalton@cumulusnetworks.com>
Acked-by: Vipin Kumar <vipin@cumulusnetworks.com>
Ticket:CM-6534
Reviewed by:CCR-3239
Testing: See Bug
Dynamic neighbors did not work properly with multiple bgp instances.
This was caused by the lookup for the dynamic range attempting to
break out of two for loops at the same time. The break only stopped
the innermost for loop, causing it to only ever find the listen-range
for the last instance in the bm->bgp list.
Additional bug fix for dynamic listen for peer groups that are configured
with internal or external key word.
Ticket: CM-7177
Reviewed-by: CCR-3396
Testing: See bug
This code change does several small things:
(A) Fix a couple detected memory leaks
(B) Fix all malloc operations to use the correct XMALLOC operation in bgpd and parts of lib
(C) Adds a few new memory types to make it easier to detect issues
Ticket: CM-6789
Reviewed By: CCR-3263
Testing Done: Manual Testing and smoke tests
Whenever some sort of output is encountered, added a json version with
proper logic as well.
When deleting a set of peers, the peer->group pointer was being set to NULL
and then passed into peer_delete.
peer_delete has functionality to safely remove the peer->group structure if it
non-null and to remove the peer->group if it's refcnt reaches zero.
This is a day one bug in the quagga source tree.
OSPF BFD command enhancement to configure BFD parameters (detect multiplier, min rx and min tx).
interface <if-name>
ip ospf bfd <detect mult> <min rx> <min tx>
This patch also adds BFD support for IPv6 OSPF. ospf6d will dynamically register/deregister IPv6 neighbors with BFD for monitoring the connectivity of the neighbor. Neighbor is registered with BFD when 2-way adjacency is established and deregistered when adjacency goes down if the BFD is enabled on the interface through which the neighbor was discovered.
OSPF6 BFD command added to configure BFD and parameters (detect multiplier, min rx and min tx).
interface <if-name>
ipv6 ospf6 bfd <detect mult> <min rx> <min tx>
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
BGP: Determine peer's IP address if interface has /30, /31
Allow interface-based session config for IPv4 numbered links
if the link address is either /30 or /31. This is not RFC5549,
but can be deployed now, and independent of whether the peer
supports RFC5549 or not.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-By: Vivek Venkataram <vivek@cumulusnetworks.com>
deleted from the listen socket in some situations. This would lead
to incorrect behavior where a BGP connection from a peer that does
not specify the MD5 option would be accepted.
This patch also adds BFD multihop support for BGP. Whether a peer is multi-hop or single hop is determined internally. All IGP peers are considered as multi-hop peers. EBGP peers are considered as single hop unless configured as multi-hop.
BGP BFD command enhancement to configure BFD parameters (detect multiplier, min rx and min tx).
router bgp <as-number>
neighbor <name/ip-address> bfd <detect mult> <min rx> <min tx>
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
"bgp confederation id X" are the same value.
router bgp 1
bgp router-id 10.1.1.1
bgp confederation identifier 1
bgp confederation peers 24 35
neighbor 10.1.1.2 remote-as 24
neighbor 10.1.1.2 update-source lo
neighbor 10.1.1.3 remote-as 1
neighbor 10.1.1.3 update-source lo
The customer does this because they want to peer to 10.1.1.2 as a
confed-external peer but peer with 10.1.1.3 as a normal iBGP peer.
The bug was that we thought 10.1.1.3 was an EBGP peer so we did not send him
LOCALPREF which caused the Juniper to send us a NOTIFICATION. I confirmed
that quagga also sends a NOTIFICATION in this scenario.
The fix is to add a check to see if router bgp X and bgp confederation
identifier X are equal because that is a factor in determining if a peer is
EBGP or IBGP
Additional issues fixed in the this patch:
We were not properly removing all AS_CONFED_SEQUENCEs/SETs from the aspath
when advertising a route to an ebgp peer. This was due to two issues:
We only called aspath_delete_confed_seq() if confederations were
configured. We can RX as aspath with CONFED segments even if
confederations are not configured.
aspath_delete_confed_seq() was implemented based on the original confed
RFC 3065 which basically said "remove all of the leading
AS_CONFED_SEQUENCEs/SETs" where the new confed RFC 5065 says "remove ALL
of the AS_CONFED_SEQUENCEs/SETs"
peer-groups did not work for confed-external peers. peer_calc_sort() always
returned BGP_PEER_EBGP for a confederations where the remote-as was not
specified. The reason was the peer->as_type was AS_UNSPECIFIED but we checked
if (peer->as_type != AS_SPECIFIED)
return (peer->as_type == AS_INTERNAL ? BGP_PEER_IBGP : BGP_PEER_EBGP);
After fixing that I found that when we got to the else where we checked for
peer1 we could only possibly return BGP_PEER_IBGP or BGP_PEER_EBGP, we need
to also be able to return BGP_PEER_CONFED. I changed this to return
peer1->sort.
"show ip bgp x.x.x.x" would always display "Local" for the aspath. This is
because we were calling aspath_counts_hop() to determine if the aspath was
empty. This is wrong though because CONFED segments do not count towards
aspath hopcount. The fix is to null check aspath->segments to determine if
the aspath is actually empty.
"show ip bgp x.x.x.x" and "show ip bgp neighbor" always displayed
"internal" or "external" and never "confed-internal" or "confed-external".
This made troubleshooting difficult because I couldn't tell exactly what
kind of peer I was dealing with. I added the confed-internal and
confed-external output...also added a "peer-type" field in the json output
for 'show ip bgp x.x.x.x'
"show ip bgp peer-group" did not list the peer-group name if we hadn't
determined the "type" (internal, external, etc) for the peer-group
This adds support for BGP RFC 5549 (Extended Next Hop Encoding capability)
* send and receive of the capability
* processing of IPv4->IPv6 next-hops
* for resolving these IPv6 next-hops, itsworks with the current
next-hop-tracking support
* added a new message type between BGP and Zebra for such route
install/uninstall
* zserv side of changes to process IPv4 prefix ->IPv6 next-hops
* required show command changes for IPv4 prefix having IPv6 next-hops
Few points to note about the implementation:
* It does an implicit next-hop-self when a [IPv4 prefix -> IPv6 LL next-hop]
is to be considered for advertisement to IPv4 peering (or IPv6 peering
without Extended next-hop capability negotiated)
* Currently feature is off by default, enable it by configuring
'neighbor <> capability extended-nexthop'
* Current support is for IPv4 Unicast prefixes only.
IMPORTANT NOTE:
This patch alone isn't enough to have IPv4->IPv6 routes installed into
the kernel. A separate patch is needed for that to work for the netlink
interface.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Vivek Venkatraman <vivek@cumulusnetworks.com>
Donald Sharp <sharpd@cumulusnetworks.com>
BGP: Fix EBGP multihop transitions correctly
Since BGP connection setup has migrated to using NHT to decide when to bring a
session up, we have to handle ebgp multihop transitions correctly to ensure NHT
registrations are correctly handled.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
bgp: Fix of peer group internal and external show run output
When doing a show run for peer-groups in bgp, the remote-as was not being printed
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by:
bgpd: Exchange hostname capability and display hostnames in outputs
This patch adds a hostname capability. The node's hostname and
domainname are exchanged in the new capability and used in show command
outputs based on a knob enabled by the user. The hostname and domainname
can be a maximum of 64 chars long, each.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com>
bgp: Fixup of the remote-as command to allow user to not have to enter an actual as number
Signed-off-by: Donald Sharp<sharpd@cumulusnetworks.com>
Reviewed-by:
BGP: Fix network import check use with NHT instead of scanner
When next hop tracking was implemented and the bgp scanner was eliminated,
the "network import-check" command got broken. This patch fixes that
issue. NHT is used to not just track nexthops, but also the static routes
that are announced as part of BGP's network command. The routes are
registered only when import-check is enabled. To optimize performance,
we register static routes only when import-check is enabled.
Signed-off-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
deleted while in other situations, the peer continues to exist but its
global flags have all been reset. This is incorrect, particularly for the
CONFIG_NODE flag as other parts of the code depend on this flag being set
for a configured peer. This patch ensures that the correct flags still
remain set for the peer after unbind from its peer-group.
state through bgp_ignore() as that may not do required cleanup. Instead,
define a new event handler to handle such cases, which will go through
bgp_stop(). A similar change is also done to handle the case where an
event handler fails.
Also add a couple of variables to keep track of events for a peer.
sockunion_same() and bgp_peer_conf_if_to_su_update() need to use the scope_id
field of the ipv6 address to uniquify/identify the address.
This allows sessions based on link local address when that address is not
unique across peers.
