This change addresses the following :
1. Ensures zlog_debug should be under DEBUG macro check
2. Ensures zlog_err and zlog_warn wherever applicable.
3. Removed few posivite logs from fpm handling, whose frequency is high.
Signed-off-by: vishaldhingra <vdhingra@vmware.com>
speed interface is done 15 seconds after interface creation. during that
time, the vrf or the interface may have disappeared. to protect this,
return an error in case it is not possible to create a vrf socket or it
is not possible to get speed of an interface because of a missing
device.
Signed-off-by: Julien Floret <julien.floret@6wind.com>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The `destination` field of the connection structure was used to store
the broadcast address, if the connection was not p2p. This multipurpose
is not very evident and the benefits over calculating the bcast address
on the fly minimal.
Signed-off-by: Juergen Werner <juergen@opensourcerouting.org>
When displaying the master interface's information in "show interface",
the display is currently the ifindex of the master interface. Make it
display the name as well as that is more useful than the name.
Signed-off-by: Dinesh G Dutt<5016467+ddutt@users.noreply.github.com>
The code as written before this code change point would enqueue
every system route type to be refigured when we have an
interface event. I believe this was to originally handle bugs
in the way nexthop tracking was handled, mainly that if you keep
asking the question you'll eventually get the right answer.
Modify the code to not do this, we have fixed nexthop tracking
to not be so brain dead and to know when it needs to refigure
a route that it is tracking.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Initial commit of understanding interface speed changes
on startup was this commit:
dc7b3caefb
Effectively we had encountered situations on system startup
where the interface speed for a device was not properly setup
when zebra learns about the interface ( Imagine a bond being
brought up and the controlling software creating the bond
is not fast given system load, the bond's speed changes
upwards for each interface added ).
The initial workup on this was to allow a 15 second window
and then just reread the interface speed. We've since noticed
that under heavy system load on startup this is not always sufficient.
So modify the code to wait the 15 seconds and then check the interfaces
speed. If the interfaces speed is still MAX_UINT32T or it has changed
let's wait a bit longer and try again.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Found that the "show interface brief" command was missing the
ability to specify all vrfs. Added that capability via this
fix.
Ticket: CM-25139
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Field vrf_id is replaced by the pointer of the struct vrf *.
For that all other code referencing to (interface)->vrf_id is replaced.
This work should not change the behaviour.
It is just a continuation work toward having an interface API handling
vrf pointer only.
some new generic functions are created in vrf:
vrf_to_id, vrf_to_name,
a zebra function is also created:
zvrf_info_lookup
an ospf function is also created:
ospf_lookup_by_vrf
it is to be noted that now that interface has a vrf pointer, some more
optimisations could be thought through all the rest of the code. as
example, many structure store the vrf_id. those structures could get
the exact vrf structure if inherited from an interface vrf context.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
vrf_id parameter is replaced with struct vrf * parameter. It is
needed to create vrf structure before entering in the fuction.
an error is generated in case the vrf parameter is missing.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
the interface search is based on vrfs. As at startup, some interfaces
may be configured, there is need to have vrfs contexts present. A macro
is being appended with an extra parameter that permits create a vrf and
return the context. This macro is also used by some show routines, but
will not create vrfs, because that extra parameter will be set to false,
on that case.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Upon accessing interface NB API, the interface is created, if the vrf
is available. the commit does not change the behaviour, since at this
commit, this is not yet possible to have vrf contexts, while zebra did
not connect to daemons. However, that commit adds some work, so that it
will be possible to work on a vrf context, without having the vrf_id
completely resolved. for instance, if we suppose a vrf is created by
command 'vrf TOTO' in the starting configuration of a daemon, then 'interface
TITI vrf TOTO' will permit to create interface TITI within vrf TOTO.
the macro VRF_GET_INSTANCE will return the vrf context, if available or
not.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
the vrf_id parameter is replaced by struct vrf * parameter.
this impacts most of the daemons that look for an interface based on the
name and the vrf identifier.
Also, it fixes 2 lookup calls in zebra and sharpd, where the vrf_id was
ignored until now.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The alias/description of an interface in linux was being
used to override the internal description. As such let's
fix the display to keep track of both if we have it.
Config in FRR:
!
interface docker0
description another combination
!
interface enp3s0
description BAMBOOZLE ME WILL YOU
!
Config in linux:
sharpd@robot ~/f/zebra> ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
alias This is the loopback you cabbage
2: enp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether 74:d0:2b:9c:16:eb brd ff:ff:ff:ff:ff:ff
alias HI HI HI
Now the 'show int descr' command:
robot# show int description
Interface Status Protocol Description
docker0 up down another combination
enp3s0 up up BAMBOOZLE ME WILL YOU
HI HI HI
lo up up This is the loopback you cabbage
Fixes: #4191
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Start using the dataplane for interface-address programming,
on netlink platforms. Other platforms just stubbed at this
point.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
The master thread handler is really part of the zrouter structure.
So let's move it over to that. Eventually zserv.h will only be
used for zapi messages.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
"brief" output for "show interface" helps when we have to quickly check
important information like ip address, vrf etc. This prints
information in the easy to read tabular format. Currently it prints oper
status, ifname, vrf, ipv4 and ipv6 addresses.
Ticket: CM-9109
Signed-off-by: Nitin Soni <nsoni@cumulusnetworks.com>
Even if the neighbor entry we want already exists, force its
reinstallation to ensure that it's valid. This will now take place when
we request an update of the neighbor entry.
Ticket: CM-22604
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
The interface type can be a bond or a bond slave, add some
code to note this and to display it as part of a show interface
command.
Signed-off-by: Dinesh Dutt <didutt@gmail.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Abstract the mac neigh installation for 169.254.0.1 into
it's own function that we can pass the mac address into.
This will allow a future commit to use this functionality
when we have the appropriate mac address from reading
optional attributes of a RA packet.
Signed-off-by: Donald Sharp <sharpd@cumuusnetworks.com>
The block comments from a couple commits were not following
proper style. Fix.
Fix SA warning that had snuck in.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Netdevices are not sorted in any fashion by the kernel during the initial
interface nldump. So you can get an upper device (such as an SVI) before
its corresponding lower device (bridge).
To fix this problem we skip resolving link dependencies during handling of
nldump notifications. Resolving instead at the end (when all the devices
are present)
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Ticket: CM-22388, CM-21796
Reviewed By: CCR-7845
Testing Done:
1. verified on a setup with missing linkages
2. automation - evpn-min
This crash occurs only with netns implementation.
vrf meaning is different regarging its implementation (netns or
vrf-lite)
- With vrf-lite implementation vrf is a property of the interface that
can be changed as the speed or the state (iproute2 command: "ip link
set dev IF_NAME master VRF_NAME"). All interfaces of the system are in
the same netns and so interface name is unique.
- With netns implementation vrf is a characteristic of the interface
that CANNOT be changed: it is the id of the netns where the interface
is located. To change the vrf of an interface (iproute2 command to
move an interface "ip netns exec VRF_NAME1 ip link set dev IF_NAME
netns VRF_NAME2") the interface is deleted from the old vrf and
created in the new vrf.
Interface name is not unique, the same name can be present in the
different netns (typically the lo interface) and search of interface
must be done by the tuple (interface name, netns id).
Current tests on the vrf implementation (vrf-lite or netns) are not
sufficient. In some cases (for example when an interface is moved from
a vrf X to the default vrf and then move back to VRF X) we can have a
corruption message and then a crash of zebra.
To avoid this corruption test on the vrf implementation, needed when an
interface changes, has been rewritten:
- For all interface changes except deletion the if_get_by_name function,
that checks if an interface exists and creates or updates it if
needed, is changed:
* The vrf-lite implementation is unchanged: search of the interface
is based only on the name and update the vrf-id if needed.
* The netns implementation search of the interface is based on the
(name, vrf-id) tuple and interface is created if not found, the
vrf-id is never updated.
- deletion of an interface (reception of a RTM_DELLINK netlink message):
* The vrf-lite implementation is unchanged: the interface
information are cleared and the interface is moved to the default
vrf if it does not belong to (to allow vrf deletion)
* The netns implementation is changed: only the interface
information are cleared and the interface stays in its vrf to
avoid conflict with interface with the same name in the default
vrf.
This implementation reverts (partially or totally):
commit 393ec5424e ("zebra: fix missing node attribute set in ifp")
commit e9e9b1150f ("lib: create interface even if name is the same")
commit 9373219c67 ("zebra: improve logs when replacing interface to an
other netns")
Fixes: b53686c52a ("zebra: delete interface that disappeared")
Signed-off-by: Thibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
when interface is a virtual ethernet interface, then there is no need to
update link pointer of interface.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
