Even if some of the attributes in bgp_path_info_extra are
not used, their memory is still allocated every time. It
cause a waste of memory.
This commit code deletes all unnecessary attributes and
changes the optional attributes to pointer storage. Memory
will only be allocated when they are actually used. After
optimization, extra info related memory is reduced by about
half(~400B -> ~200B).
Signed-off-by: Valerian_He <1826906282@qq.com>
Use %pI4/%pI6 where possible, otherwise at least atjust stack buffer sizes
for inet_ntop() calls.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Null-checking "path->attr" suggests that it may be null, but it has
already been dereferenced on all paths leading to the check.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Convert the `struct attr`->ipv6_ecommunity to use
accessor functions. We'll be able to reduce memory
usage in the `struct bgp_attr` by doing this.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
a dereference of null pointer exists in current flowspec code, with
prefix pointer. check validity of pointer before going ahead.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
in addition to ipv4 flowspec, ipv6 flowspec address family can configure
its own list of interfaces to monitor. this permits filtering the policy
routing only on some interfaces.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
rfc 5701 is supported. it is possible to configure in bgp vpn, a list of
route target with ipv6 external communities to import. it is to be noted
that this ipv6 external community has been developed only for matching a
bgp flowspec update with same ipv6 ext commmunity.
adding to this, draft-ietf-idr-flow-spec-v6-09 is implemented regarding
the redirect ipv6 option.
Practically, under bgp vpn, under ipv6 unicast, it is possible to
configure : [no] rt6 redirect import <IPV6>:<AS> values.
An incoming bgp update with fs ipv6 and that option matching a bgp vrf,
will be imported in that bgp vrf.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
this commit supports [0] where ipv6 address is encoded in nexthop
attribute of nlri, and not in bgp redirect ip extended community. the
community contains only duplicate information or not.
Adding to this, because an action or a rule needs to apply to either
ipv4 or ipv6 flow, modify some internal structures so as to be aware of
which flow needs to be filtered. This work is needed when an ipv6
flowspec rule without ip addresses is mentioned, we need to know which
afi is served. Also, this work will be useful when doing redirect VRF.
[0] draft-simpson-idr-flowspec-redirect-02.txt
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
in ipv6 flowspec, a new type is defined to be able to do filtering rules
based on 20 bits flow label field as depicted in [0]. The change include
the decoding by flowspec, and the addition of a new attribute in policy
routing rule, so that the data is ready to be sent to zebra.
The commit also includes a check on fragment option, since dont fragment
bit does not exist in ipv6, the value should always be set to 0,
otherwise the flowspec rule becomes invalid.
[0] https://tools.ietf.org/html/draft-ietf-idr-flow-spec-v6-09
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
as per [0], ipv6 adress format introduces an ipv6 offset that needs to
be extracted too. The change include the validation, decoding for
further usage with policy-routing and decoding for dumping.
[0] https://tools.ietf.org/html/draft-ietf-idr-flow-spec-v6-09
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
until now, the assumption was done in bgp flowspec code that the
information contained was an ipv4 flowspec prefix. now that it is
possible to handle ipv4 or ipv6 flowspec prefixes, that information is
stored in prefix_flowspec attribute. Also, some unlocking is done in
order to process ipv4 and ipv6 flowspec entries.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This is the bulk part extracted from "bgpd: Convert from `struct
bgp_node` to `struct bgp_dest`". It should not result in any functional
change.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Add new function `bgp_node_get_prefix()` and modify
the bgp code base to use it.
This is prep work for the struct bgp_dest rework.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Modify more code to use `const struct prefix` throughout
bgp. This is all prep work for adding an accessor function
for bgp_node to get the prefix and reduce all the places that
code needs to be touched when we get that work done.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We make the assumption that ->attr is not NULL throughout
the code base. We are totally inconsistent about application
of this though.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
bgp entries in bgp_extra_path structure will be allocated as lists, only
when needed, that is to say when bgp fs entries will be received and
installed on the underlying system.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
the list of iprules is displayed in the 'show bgp ipv4 flowspec detail'
The list of iprules is displayed, only if it is installed.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
that new option will overwrite simpson draft. There is a new ecommunity
option whose type is 0x1 and subtype is 0xc. That option is defined
here on iana.org/assignments/bgp-extended-communities page:
- bgp-extended-communities.xhtml#trans-ipv4
It contains the IP address to redirect traffic to. The understanding of
the draft is the following one:
- if that community is only present, then the ip contained inside will
be chosen as nexthop.
- if that community is provided along with simpson extended community,
then only the new redirect ip draft will be used. however, both will be
displayed.
- in other cases, if there is only the simpson extended community, then
the nexthop IP of the NLRI will be chosen.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The bgp_info data is stored as a void pointer in `struct bgp_node`.
Abstract retrieval of this data and setting of this data
into functions so that in the future we can move around
what is stored in bgp_node.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Do a straight conversion of `struct bgp_info` to `struct bgp_path_info`.
This commit will setup the rename of variables as well.
This is being done because `struct bgp_info` is not descriptive
of what this data actually is. It is path information for routes
that we keep to build the actual routes nexthops plus some extra
information.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Avoid memory leak in bgp flowspec list.
Usage of bool parameter instead of int, to handle the number of entries
PBR.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When configuring an interface, the no local-install any command appears,
and leads to confusions. because the effect of that command differs if
it is executed after local-install <interfaces> or before executing
local-install <interfaces>, the proposal fix here is to suppress that
command from the vty available commands.
PR=59595
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Acked-by: Alain Ritoux <alain.ritoux@6wind.com>
because the IP destination criterium may match several entries, the show
command may return more than one entry.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Because one flowspec entry can create 1-N bgp pbr entries, the list is
now updated and visible. Also, because the bgp_extra structure is used,
this list is flushed when the bgp_extra structure is deleted.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
As fragment bitmask and tcpflags bitmask in flowspec protocol is encoded
in the same way, it is not necessary to differentiate those two fields.
Moreover, it overrides the initial fragment limit set to 1. It is now
possible to handle multiple framgent values.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
policy routing is configurable via address-family ipv4 flowspec
subfamily node. This is then possible to restrict flowspec operation
through the BGP instance, to a single or some interfaces, but not all.
Two commands available:
[no] local-install [IFNAME]
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Once PBR rules installed, an information is printed in the main
show bgp ipv4 flowspec detail information.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Most presumably, the nexthop IP is present, only when ECOM redirect IP
is present. The nexthop is displayed.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
snprintf routine is used widely, when the handler routine in charge of
displaying the output is called.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The json format is returd when requested from the two commands:
- show bgp ipv4 flowspec
- show bgp ipv4 flowspec detail
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
It is possible to enhance debug bgp flowspec feature by using vty
command. This command, if enabled, will dump the match/set couple of
information received on NLRI.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The show bgp ipv4 flowspec routine is made available, displays the
flowspec rules contained in the BGP FIB database, as well as the actions
to be done on those rules. Two routines are available:
show bgp ipv4 flowspec
show bgp ipv4 flowspec detail
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
