At bgpd startup, VRF instances are sent from zebra before the
interfaces. When importing a l3vpn prefix from another local VRF
instance, the interfaces are not known yet. The prefix nexthop interface
cannot be set to the loopback or the VRF interface, which causes setting
invalid routes in zebra.
Update route leaking when the loopback or a VRF interface is received
from zebra.
At a VRF interface deletion, zebra voluntarily sends a
ZEBRA_INTERFACE_ADD message to move it to VRF_DEFAULT. Do not update if
such a message is received. VRF destruction will destroy all the related
routes without adding codes.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
If 'network import-check' is defined on the source BGP session, prefixes
that are stated in the network command cannot be leaked to the other
VRFs BGP table even if they are present in the origin VRF RIB if the
'rt import' statement is defined after the 'network <prefix>' ones.
When a prefix nexthop is updated, update the prefix route leaking. The
current state of nexthop validation is now stored in the attributes of
the bgp path info. Attributes are compared with the previous ones at
route leaking update so that a nexthop validation change now triggers
the update of destination VRF BGP table.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
If 'network import-check' is defined on the source BGP session, prefixes
that are stated in the network command cannot be leaked to the other
VRFs BGP table even if they are present in the origin VRF RIB.
Always validate the nexthop of BGP static routes (i.e. defined with the
network statement) if 'network import-check' is defined on the source
BGP session and the prefix is present in source RIB.
It fixes the issue when the 'rt import' statement is defined after the
'network' ones.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Prefixes that are stated in the network command cannot be leaked to
the other VRFs BGP table whether or not they are present in the origin
VRF RIB.
Always validate the nexthop of BGP static routes (i.e. defined with the
network statement) if 'no network import-check' is defined on the source
BGP session.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When we use vrf-to-vrf export, the nexthop has already not been
overridden when the peer is BGP unnumberred. However, when we use normal
export, the nexthop will be oberridden. This behavior will make the VPN
routes invalid in VPN RIB.
This PR stops overriding nexthop even if we use normal export.
Signed-off-by: Ryoga Saito <ryoga.saito@linecorp.com>
The first argument of sid_unregister should be default bgp instance.
However, these functions passed VRF bgp instance to this funciton.
Signed-off-by: Ryoga Saito <ryoga.saito@linecorp.com>
Currently bgpd uses the opaque codepoint (0xFFFF) in the BGP
advertisement. In this commit, we update bgpd to use the SRv6 codepoints
defined in the IANA SRv6 Endpoint Behaviors Registry
(https://www.iana.org/assignments/segment-routing/segment-routing.xhtml)
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
This commit changes some debug prints to use `%pI6` instead of
`inet_ntop` to print SRv6 SIDs.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
`srv6_locator_chunk_free()` takes care of freeing the memory allocated
for a `struct srv6_locator_chunk` and setting the
`struct srv6_locator_chunk` pointer to NULL.
It is not necessary to explicitly set the pointer to NULL after invoking
`srv6_locator_chunk_free()`.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
A programmer can use the `srv6_locator_chunk_free()` function to free
the memory allocated for a `struct srv6_locator_chunk`.
The programmer invokes `srv6_locator_chunk_free()` by passing a single
pointer to the `struct srv6_locator_chunk` to be freed.
`srv6_locator_chunk_free()` uses `XFREE()` to free the memory.
It is the responsibility of the programmer to set the
`struct srv6_locator_chunk` pointer to NULL after freeing memory with
`srv6_locator_chunk_free()`.
This commit modifies the `srv6_locator_chunk_free()` function to take a
double pointer instead of a single pointer. In this way, setting the
`struct srv6_locator_chunk` pointer to NULL is no longer the
programmer's responsibility but is the responsibility of
`srv6_locator_chunk_free()`. This prevents programmers from making
mistakes such as forgetting to set the pointer to NULL after invoking
`srv6_locator_chunk_free()`.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
The command `sid vpn per-vrf export (1-255)|auto` can be used to export
IPv4 and IPv6 routes from a VRF to the VPN RIB using a single SRv6 SID
(End.DT46 behavior).
This commit implements the no form of the above command, which can be
used to disable the export of the IPv4/IPv6 routes:
`no sid vpn per-vrf export`.
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
In the current implementation of bgpd, SRv6 SIDs can be configured only
under the address-family. This enables bgpd to leak IPv6 routes using
an SRv6 End.DT6 behavior and IPv4 routes using an SRv6 End.DT4
behavior. It is not possible to leak both IPv6 and IPv4 routes using a
single SRv6 SID.
This commit adds a new CLI command
"sid vpn per-vrf export <sid_idx|auto>" that enables bgpd to leak both
IPv6 and IPv4 routes using a single SRv6 SID (End.DT46 behavior).
Signed-off-by: Carmine Scarpitta <carmine.scarpitta@uniroma2.it>
In order to send correct SRv6 L3VPN advertisement, we need to save
srv6_locator_chunk in vpn_policy. With this information, we can
construct correct SRv6 L3VPN advertisement packets.
Signed-off-by: Ryoga Saito <ryoga.saito@linecorp.com>
When router id is changed through config, new RD is auto generated.
However new export RT was being assigned without freeing
the older RT from VRF.
Signed-off-by: Samanvitha B Bhargav <bsmanvitha@vmware.com>
RFC4364 describes peerings between multiple AS domains, to ease
the continuity of VPN services across multiple SPs. This commit
implements a sub-set of IETF option b) described in chapter 10 b.
The ASBR to ASBR approach is taken, with an EBGP peering between
the two routers. The EBGP peering must be directly connected to
the outgoing interface used. In those conditions, the next hop
is directly connected, and there is no need to have a transport
label to convey the VPN label. A new vty command is added on a
per interface basis:
This command if enabled, will permit to convey BGP VPN labels
without any transport labels (i.e. with implicit-null label).
restriction:
this command is used only for EBGP directly connected peerings.
Other use cases are not covered.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Let's convert to our actual library call instead
of using yet another abstraction that makes it fun
for people to switch daemons.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
A new command is available under SAFI_MPLS_VPN:
With this command, the BGP vpnvx prefixes received are
not kept, if there are no VRF interested in importing
those vpn entries.
A soft refresh is performed if there is a change of
configuration: retain cmd, vrf import settings, or
route-map change.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The bgp_nexthop must be the source bgp structure. It cannot be the
destination bgp one.
Use bgp_orig source bgp struct by default.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
The "struct bgp" variable names in the mplsvpn bgp code do not
explicitly say whether they refer to a source or destination BGP
instance. Some variable declarations are commented out with "from" and
"to" but this does not avoid confusion within the functions. The names
of "struct bgp" variables are reused in different functions but their
names sometimes refer to a source instance and sometimes to a
destination instance.
Rename the "struct bgp" variable names to from_bgp and to_bgp.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Prior to this fix, the magic number (16) was used regardless of what value
the user specified for func-bits. With this fix, user-specified values are
handled appropriately.
Signed-off-by: Nobuhiro MIKI <nmiki@yahoo-corp.jp>
Until now, it has been hard-coded that the position at which the label
is inserted is from the 64th bits. Therefore, when the Locator prefix
was not /64, incorrect SIDs were generated. Also, SIDs are generated
in duplicate on Lines 604 & 613 in bgpd/bgp_mplsvpn.c.
In this patch, the position where the label is inserted is calculated
based on the sum of block_bits_length and node_bits_length (i.e., the
user-specified Locator prefix length). In addition, SID generation is
performed at one location in alloc_new_sid.
Signed-off-by: Nobuhiro MIKI <nmiki@yahoo-corp.jp>
Since additional information such as block_bits_length is needed to
generate SIDs properly, the type of elements in srv6_locator_chunks
list is extended from "struct prefix_ipv6 *" to
"struct srv6_locator_chunk *". Even in terms of variable name,
"struct srv6_locator_chunk *" is appropriate.
Signed-off-by: Nobuhiro MIKI <nmiki@yahoo-corp.jp>
This patch adds transpostion_offset and transposition_len to bgp_sid_info,
and transposes SID only at bgp_zebra_announce.
Signed-off-by: Ryoga Saito <ryoga.saito@linecorp.com>
This patch changes the format of the Prefix-SID advertised by
bgpd. In current implementation, transposed SIDs were
advertised, which caused two problems:
1. bgpd that receives SRv6 L3VPN routes whose SID is
transposed couldn't put bgp_attr_srv6_l3vpn whose those
routes together. This leads extra memory consumption.
2. Some implementation will reject a route with transposed SID.
This will affect interoperability.
For those reasons, in this patch, instead of advertising
transposed SID, we change it to advertise the locator of SID.
Signed-off-by: Ryoga Saito <ryoga.saito@linecorp.com>
For the later patches, this patch changes the behavior of alloc_new sid
so that bgpd record not only SID for VRF, but also Locator of SID.
Signed-off-by: Ryoga Saito <ryoga.saito@linecorp.com>
Description:
Incorrect behavior during best path selection for the imported routes.
Imported routes are always treated as eBGP routes.
Change is intended for fixing the issues related to
bgp best path selection for leaked routes:
- FRR does ecmp for the imported routes,
even without any ecmp related config.
If the same prefix is imported from two different VRFs,
then we configure the route with ecmp even without
any ecmp related config.
- Locally imported routes are preferred over imported
eBGP routes.
If there is a local route and eBGP learned route
for the same prefix, if we import both the routes,
imported local route is selected as best path.
- Same route is imported from multiple tenant VRFs,
both imported routes point to the same VRF in nexthop.
- When the same route with same nexthop in two different VRFs
is imported from those two VRFs, route is not installed as ecmp,
even though we had ecmp config.
- During best path selection, while comparing the paths for imported routes,
we should correctly refer to the original route i.e. the ultimate path.
- When the same route is imported from multiple VRF,
use the correct VRF while installing in the FIB.
- When same route is imported from two different tenant VRFs,
while comparing bgp path info as part of bgp best path selection,
we should ideally also compare corresponding VRFs.
See-also: https://github.com/FRRouting/frr/files/7169555/FRR.and.Cisco.VRF-Lite.Behaviour.pdf
Co-authored-by: Santosh P K <sapk@vmware.com>
Co-authored-by: Kantesh Mundaragi <kmundaragi@vmware.com>
Signed-off-by: Iqra Siddiqui <imujeebsiddi@vmware.com>
draft-ietf-bess-srv6-services-07 defines new SID structure Sub-Sub-TLV.
This patch adds SID structure information to bgp_attr_srv6_l3vpn. This
patch also defines default SID stucture used by following patches.
Signed-off-by: Ryoga Saito <contact@proelbtn.com>
Current implementation of SRv6 SID allocation algorithm sets most least
2 bytes. But, according to RFC8986, function bits is located in the next
to locator. New allocation alogirithm respects this format.
Signed-off-by: Ryoga Saito <contact@proelbtn.com>
In eusure_vrf_tovpn_sid, there is a check to ensure not to select both
SID index and SID auto mode. But, this current check is wrong and not
meaningful.
Signed-off-by: proelbtn <contact@proelbtn.com>
Some BGP updates received by BGP invite local router to
install a route through itself. The system will not do it, and
the route should be considered as not valid at the earliest.
This case is detected on the zebra, and this detection prevents
from trying to install this route to the local system. However,
the nexthop tracking mechanism is called, and acts as if the route
was valid, which is not the case.
By detecting in BGP that use case, we avoid installing the invalid
routes.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Coverity scan found this issue. The bgp_vrf variable in
ensure_vrf_tovpn_sid() has already been derefed in all paths
at this point in time. No need to check for it existing
at this point.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
This commit make bgpd to support VPN SID advertisement
as BGP Prefix-SID when route-leaking from BGP-vrf instance
to BGP-vpn instance.
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
This commit add cil to configure BGP SRv6-VPN sid allocation.
Almost mechanism are based on BGP MPLS-VPN.
User can allocate and export sid with using following config.
Then bgpd try to allocate new SID to redirect vpn to vrf using
SRv6 localsid End.DT4/DT6. Currently linux kernel will regect
End.DT4 route install due to no-implementation.
(at-least today's FRR's ci kernel.)
So now we only supports BGP SRv6-VPNv6.
router bgp 1
segment-routing srv6
locator loc1
!
address-family ipv6 vpn
exit-address-family
!
router bgp 1 vrf vrf10
address-family ipv6 unicast
sid vpn export 1 !!(option1)!!
sid vpn export auto !!(option2)!!
exit-address-family
!
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
Description:
Route leaking from default vrf to non-default vrf stops after frr restart.
If the interface comes up after route leaking is configured,
in the case of vpn router id update, we delete the ecommunity value
and never reconfigure the rtlist.
This results in skipping route leak to non-default vrfs (vpn to vrf).
Router-id change that is not explicitly configured
(a change from zebra, frr restart) should not replace a configured vpn RD/RT.
Added few helpful debugs as well.
Co-authored-by: Santosh P K <sapk@vmware.com>
Co-authored-by: Kantesh Mundaragi <kmundaragi@vmware.com>
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
Problem:
Stale routes are seen in the bgp table(ipv4 and ipv6)
RCA:
Scenario1:
Interface down and withdraw is in-progress.
Router bgp config leading to re-leaking.
Now, withdraw-in-progress routes,
are again leaked to bgp vrf instance(s) importing routes.
Whenever we see an interface down
and corresponding address delete,
while withdrawal of exported routes is in-progress,
routes are marked as being removed and put into work queue.
‘router bgp’ config is updated, which triggers
bgp_vpn_leak_export; which exports routes from configured bgp vrf to VPN.
So withdraw-in-progress routes,
are again leaked to bgp vrf instance(s) importing routes; leading to stale routes.
Scenario2:
- 'no import vrf non-default-vrf’ [in the default vrf]
- bgp update from the peer withdrawing prefix [non-default vrf]
- 'import vrf non-default-vrf’ [configured in the default vrf]
While withdrawal of exported routes is in-progress,
routes are marked as being removed and put into work queue,
In the meantime, if import vrf is configured,
which exports routes from configured bgp vrf to VPN.
So withdraw-in-progress new routes,
are again leaked to bgp vrf instance(s) importing routes; leading to stale routes.
Fix:
Whenever leaking routes (leak_update),
for already existing routes,
skip the routes with bgp_path_info
marked as being removed.
Also added the log message for the return.
Co-authored-by: Santosh P K <sapk@vmware.com>
Co-authored-by: Kantesh Mundaragi <kmundaragi@vmware.com>
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
Description:
Imported/leak-from routes do not get withdrawn/removed
even if the source VRF is deleted.
Deleting and re-adding a tenant vrf, does not refresh the RIB.
Whenever VRF is deleted (bgp_vrf_disable),
currently we are withdrawing leak-from-vrf and
leak-to-vrf routes from vpn table for the vrf,
which is deleted.
But we are currently not withdrawing routes from leak-to vrfs.
We should also withdraw leak-to routes
from leak-to vrfs (calling vpn_leak_to_vrf_withdraw).
Co-authored-by: Santosh P K <sapk@vmware.com>
Co-authored-by: Kantesh Mundaragi <kmundaragi@vmware.com>
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
New and improved submission for this commit -- updated to accommodate
changes from 4027d19b0.
Adds support for 'rd all' matching for EVPN and L3VPN show commands.
Introduces evpn_show_route_rd_all_macip().
Cleans up some show commands to use SHOW_DISPLAY string constants.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Adds support for 'rd all' matching for EVPN and L3VPN show commands.
Introduces evpn_show_route_rd_all_macip().
Cleanup some show commands to use SHOW_DISPLAY string constants.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
If we are using a nexthop for a MPLS VPN route make sure the
nexthop is over a labeled path. This new check mirrors the one
in validate_paths (where routes are enabled when a nexthop
becomes reachable). The check is introduced to the code path
where routes are added and the nexthop is looked up.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
The `struct ecommunity` structure is using an int for a size value.
Let's switch it over to a uint32_t for size values since a size
value for data can never be negative.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
If we are attempting to store the bgp name for route
leaking and we find a match do not leak the memory.
Please note this is probably not really going to happen
ever.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The route_map_object_t was being used to track what protocol we were
being called against. But each protocol was only ever calling itself.
So we had a variable that was only ever being passed in from route_map_apply
that had to be carried against and everyone was testing if that variable
was for their own stack.
Clean up this route_map_object_t from the entire system. We should
speed some stuff up. Yes I know not a bunch but this will add up.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
gcc 10 complains about some of our format specs, fix them. Use
atomic size_t in thread stats, to work around platform
differences.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
==916511== 18 bytes in 2 blocks are definitely lost in loss record 7 of 147
==916511== at 0x483877F: malloc (vg_replace_malloc.c:307)
==916511== by 0x4BE0F0A: strdup (strdup.c:42)
==916511== by 0x48D66CE: qstrdup (memory.c:122)
==916511== by 0x1E6E31: bgp_vpn_leak_export (bgp_mplsvpn.c:2690)
==916511== by 0x28E892: bgp_router_create (bgp_nb_config.c:124)
==916511== by 0x48E05AB: nb_callback_create (northbound.c:869)
==916511== by 0x48E0FA2: nb_callback_configuration (northbound.c:1183)
==916511== by 0x48E13D0: nb_transaction_process (northbound.c:1308)
==916511== by 0x48E0137: nb_candidate_commit_apply (northbound.c:741)
==916511== by 0x48E024B: nb_candidate_commit (northbound.c:773)
==916511== by 0x48E6B21: nb_cli_classic_commit (northbound_cli.c:64)
==916511== by 0x48E757E: nb_cli_apply_changes (northbound_cli.c:281)
Signed-off-by: Chirag Shah <chirag@nvidia.com>
NLRI parsing for mpls vpn was missing several length checks that could
easily result in garbage heap reads past the end of nlri->packet.
Convert the whole function to use stream APIs for automatic bounds
checking...
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
rfc 5701 is supported. it is possible to configure in bgp vpn, a list of
route target with ipv6 external communities to import. it is to be noted
that this ipv6 external community has been developed only for matching a
bgp flowspec update with same ipv6 ext commmunity.
adding to this, draft-ietf-idr-flow-spec-v6-09 is implemented regarding
the redirect ipv6 option.
Practically, under bgp vpn, under ipv6 unicast, it is possible to
configure : [no] rt6 redirect import <IPV6>:<AS> values.
An incoming bgp update with fs ipv6 and that option matching a bgp vrf,
will be imported in that bgp vrf.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Remove mid-string line breaks, cf. workflow doc:
.. [#tool_style_conflicts] For example, lines over 80 characters are allowed
for text strings to make it possible to search the code for them: please
see `Linux kernel style (breaking long lines and strings)
<https://www.kernel.org/doc/html/v4.10/process/coding-style.html#breaking-long-lines-and-strings>`_
and `Issue #1794 <https://github.com/FRRouting/frr/issues/1794>`_.
Scripted commit, idempotent to running:
```
python3 tools/stringmangle.py --unwrap `git ls-files | egrep '\.[ch]$'`
```
Signed-off-by: David Lamparter <equinox@diac24.net>
This is the bulk part extracted from "bgpd: Convert from `struct
bgp_node` to `struct bgp_dest`". It should not result in any functional
change.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Problem reported where bgp sessions were being torn down for ibgp
peers with the reason being optional attribute error. Found that
when a route was leaked, the RTs were stripped but the actual
EXTCOMMUNUNITY attribute was not cleared so an empty ecommunity
attribute stayed in the bgp table and was sent in updates.
Ticket: CM-30000
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
This macro is undefined if vnc is disabled, and while it defaults to 0,
this is still wrong and causes issues with -Werror
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Add new function `bgp_node_get_prefix()` and modify
the bgp code base to use it.
This is prep work for the struct bgp_dest rework.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Problem seen that if "import vrf route-map RMAP" was entered
without any vrfs being imported, the configuration was displayed
as "route-map vpn import RMAP". Additionally, if "import vrf
route-map" was entered without specifying a route-map name,
the command was accepted and the word "route-map" would be
treated as a vrf name. This fix resolves both of those issues
and also allows deleting the "import vrf route-map" line without
providing the route-map name.
Ticket: CM-28821
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Some were converted to bool, where true/false status is needed.
Converted to void only those, where the return status was only false or true.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
