```
donatas-pc(config-router)# timers bgp 8 12
% keeplive value 8 is larger than 1/3 of the holdtime, setting to 4
donatas-pc(config-router)# do sh run | include timers bgp
timers bgp 4 12
donatas-pc(config-router)#
```
Closes https://github.com/FRRouting/frr/issues/14287
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
When the BGP 'redistribute table' command is used for a given route
table, and BGP configuration is flushed and rebuilt, the redistribution
does not work.
Actually, when flushing the BGP configuration with the 'no router bgp'
command, the BGP redistribute entries related to the 'redistribute table'
entries are not flushed. Actually, at BGP deletion, the table number is
not given as parameter in bgp_redistribute_unset() function, and the
redistribution entry is not removed in zebra.
Fix this by adding some code to flush all the redistribute table
instances.
Fixes: 7c8ff89e93 ("Multi-Instance OSPF Summary")
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
As part of the conversion to a `struct peer_connection` it will
be desirable to have 2 pointers one for when we open a connection
and one for when we receive a connection. Start this actual
conversion over to this in `struct peer`. If this sounds confusing
take a look at the bgp state machine for connections and how
it resolves the processing of this router opening -vs- this
router receiving an open. At some point in time the state
machine decides that we are keeping one of the two connections.
Future commits will allow us to untangle the peer/doppelganger
duality with this abstraction.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The status and ostatus are a function of the `struct peer_connection`
move it into that data structure.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Move PEER_THREAD_WRITES_ON and PEER_THREAD_READS_ON to
be a part of the `struct peer_connection` since this is
a connection oriented bit of data.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Move the peer->t_write and peer->t_read into `struct peer_connection`
as that these are properties of the connection.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
P# Please enter the commit message for your changes. Lines starting
BGP tracks connections based upon the peer. But the problem
with this is that the doppelganger structure for it is being
created. This has introduced a bunch of fragileness in that
the peer exists independently of the connections to it.
The whole point of the doppelganger structure was to allow
BGP to both accept and initiate tcp connections and then
when we get one to a `good` state we collapse into the
appropriate one. The problem with this is that having
2 peer structures for this creates a situation where
we have to make sure we are configing the `right` one
and also make sure that we collapse the two independent
peer structures into 1 acting peer. This makes no sense
let's abstract out the peer into having 2 connection
one for incoming connections and one for outgoing connections
then we can easily collapse down without having to do crazy
stuff. In addition people adding new features don't need
to have to go touch a million places in the code.
This is the start of this abstraction. In this commit
we'll just pull out the fd and input/output buffers
into a connection data structure. Future commits
will abstract further.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Before the patch:
```
donatas-laptop(config-router)# bgp confederation
identifier AS number in plain <1-4294967295> or dotted <0-65535>.<0-65535> format
peers Peer ASs in BGP confederation
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Even if some of the attributes in bgp_path_info_extra are
not used, their memory is still allocated every time. It
cause a waste of memory.
This commit code deletes all unnecessary attributes and
changes the optional attributes to pointer storage. Memory
will only be allocated when they are actually used. After
optimization, extra info related memory is reduced by about
half(~400B -> ~200B).
Signed-off-by: Valerian_He <1826906282@qq.com>
Add this logic inside bgp_capability_send() instead of repeating the whole
logic before calling bgp_capability_send().
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
When setting local-role for the neighbor, force sending ROLE capability via
dynamic capability if it's enabled.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
We have dynamic capability support, but it handles only MP capability.
With this change, we can enable software version capability dynamicaly, without
resetting the session.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Include an event ptr-to-ptr in the event_execute() api
call, like the various schedule api calls. This allows the
execute() api to cancel an existing scheduled task if that
task is being executed inline.
Signed-off-by: Mark Stapp <mjs@labn.net>
The last_reset_cause is a plain old BGP_MAX_PACKET_SIZE buffer
that is really enlarging the peer data structure. Let's just
copy the stream that failed and only allocate how ever much
the packet size actually was. While it's likely that we have
a reset reason, the packet typically is not going to be 65k
in size. Let's save space.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
problem:
In CLI config codeflow there are memory leaks in failure scenario
Fix:
Code changes are done to free ecommunity
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
Useful to have it for datacenter profile only, disabled for traditional.
If the peer is not established or established, but has no description set,
we will show the FRR version instead, which is kinda handy to have instead of
nothing.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
More details: https://www.rfc-editor.org/rfc/rfc8810.html
Not sure if we want to maintain the old code more.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Also, this is visible only if `capability software-version` is enabled.
Example:
```
r1# show ip bgp summary
IPv4 Unicast Summary (VRF default):
BGP router identifier 192.168.1.1, local AS number 65001 vrf-id 0
BGP table version 0
RIB entries 0, using 0 bytes of memory
Peers 1, using 725 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
192.168.1.2 4 65002 54 54 0 0 0 00:00:52 0 0 FRRouting/9.1-dev-My
Total number of neighbors 1
r1#
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
After some VRF imports are removed and "no bgp retain route-target all"
is set, prefixes that are not imported anymore remain in the BGP table.
Parse the BGP table and remove un-imported prefixes in such a case.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
When acting as intermediate device for BGP signaling, and
as transit device for data traffic, the device is not able
to modify the label value from incoming MPLS VPN updates:
- as BGP device, modifying the label value is necessary
when redistributing VPN prefixes with its own next-hop.
- as transit device that connects two ethernet segments
on separate interfaces, the return MPLS traffic must be
handled: the modified label value must be swapped with
the original label value and sent back to the original
next-hop.
The border router use case can be taken as example, when
it acts both as transit and as BGP device:
- When receiving updates from a border router peer, and where
interior traffic is expected to transit through the local
border router.
- When receiving updates from interior devices, and where
exterior traffic will transit through the local border router.
In those two situations, a new label is bound to the received
entry, and the entry is advertised to a new peer with the new
label. In the same time, an MPLS entry is created to handle
return traffic with the new mpls label: the traffic would be
swapped to the original MPLS label and the original next-hop.
This is the first commit of a series of patches, that address
the above mentioned issue.
The first commit introduces a new per-interface command:
> interface eth0
> [no] mpls bgp l3vpn-multi-domain-switching
> exit
This command will authorise mpls vpn updates to have a new
label value bound to the mpls vpn routes received over that
interface.
Link: https://www.rfc-editor.org/rfc/rfc3107.html#section-3
> When a BGP speaker redistributes a route, the label(s) assigned to
> that route must not be changed (except by omission), unless the
> speaker changes the value of the Next Hop attribute of the route.
Link: https://www.rfc-editor.org/rfc/rfc3031.html#section-4.6
Link: https://www.rfc-editor.org/rfc/rfc4364.html#section-10
sub-chapter b.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When using `addpath-tx-all` BGP announces all known paths instead of announcing
only an arbitrary number of best paths.
With this new command we can send N best paths to the neighbor. That means, we
send the best path, then send the second best path excluding the previous one,
and so on. In other words, we run best path selection algorithm N times before
we finish.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
The only places entry->any could ever be set to true was
when str was NULL. Unfortunately with the way our CLI works
str is impossible to be NonNULL. The entry->any value *used*
to work prior to commit e961923c72
but it was changed back in 2016 and no-one has noticed the changed
ability.
Let's just admit that there are no users of this and remove this
dead code.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Let's account for vpn_policy_getafi having a failure
situation and back out of the whole thing gracefully.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
A new VTY command is introduced in ipv4 unicast and ipv6 unicast
address family, under a BGP instance.
> r1# label vpn export allocation-mode per-nexthop|per-vrf
This command will update the label values associated for each
BGP update to export to the global instance. Two modes are
available: per-nexthop and per-vrf. The latter is the default
one.
With this commit only, configuring label allocation per nexthop
will only reset the BGP updates, and the per-vrf mode label
allocation will be chosen.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Until now, the bgp local paths were using the default null label
defined. It was not possible to select the null label for the ipv4
or the ipv6 address families.
This commit addresses this issues by adding two extra-parameters
to the BGP labeled-unicast command.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
In BGP labeled unicast address-family, it is not possible to
send explicit-null label values with redistributed or network
declared prefixes.
A new CLI command is introduced:
> [no] bgp labeled-unicast explicit-null
When used, the explicit-null value for IPv4 ('0' value) or
IPv6 ('2' value) will be used.
It is necessary to reconfigure the networks or the
redistribution in order to inherit this new behaviour.
Add the documentation.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When we have these sequence of events causing a crash in
evpn_type5_test_topo1:
(A) no router bgp vrf RED 100
this schedules for deletion the vrf RED instance
(B) a l3vni change event from zebra
this creates a bgp instance for VRF RED in some cases
additionally it auto imports evpn routes into VRF RED
Please note this is desired behavior to allow for the
auto importation of evpn vrf routes
(C) no router bgp 100
The code was allowing the deletion of the default
instance and causing tests to crash.
Effectively the test in bgp_vty to allow/dissallow
the removal of the default instance was not correct
for the case when (B) happens.
Let's just not allow the command to succeed in this case as that
the test was wrong.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Fix for missing neighbor description in "show bgp summary [wide]"
when its length exceeds 20[64] chars and it doesn't contain
withespaces.
Existing behavior remains if description contains whitespaces
before size limit.
Signed-off-by: rbarroetavena <rbarroetavena@gmail.com>
Effectively a massive search and replace of
`struct thread` to `struct event`. Using the
term `thread` gives people the thought that
this event system is a pthread when it is not
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
This is a first in a series of commits, whose goal is to rename
the thread system in FRR to an event system. There is a continual
problem where people are confusing `struct thread` with a true
pthread. In reality, our entire thread.c is an event system.
In this commit rename the thread.[ch] files to event.[ch].
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
A new VTY command is introduced in ipv4 unicast and ipv6 unicast
address family, under a BGP instance.
> r1# label vpn export allocation-mode per-nexthop|per-vrf
This command will update the label values associated for each
BGP update to export to the global instance. Two modes are
available: per-nexthop and per-vrf. The latter is the default
one.
With this commit only, configuring label allocation per nexthop
will only reset the BGP updates, and the per-vrf mode label
allocation will be chosen.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
It was hard to catch those unless using higher values than uint32_t, but
already hit, it's time to fix completely.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Since we increased peer->af_flags from uint32_t to uint64_t,
peer_af_flag_check() was historically returning integer, and not bool
as should be.
The bug was that if we have af_flags higher than uint32_t it will never
returned a right value.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Implement: https://datatracker.ietf.org/doc/html/draft-abraitis-bgp-version-capability
Tested with GoBGP:
```
% ./gobgp neighbor 192.168.10.124
BGP neighbor is 192.168.10.124, remote AS 65001
BGP version 4, remote router ID 200.200.200.202
BGP state = ESTABLISHED, up for 00:01:49
BGP OutQ = 0, Flops = 0
Hold time is 3, keepalive interval is 1 seconds
Configured hold time is 90, keepalive interval is 30 seconds
Neighbor capabilities:
multiprotocol:
ipv4-unicast: advertised and received
ipv6-unicast: advertised
route-refresh: advertised and received
extended-nexthop: advertised
Local: nlri: ipv4-unicast, nexthop: ipv6
UnknownCapability(6): received
UnknownCapability(9): received
graceful-restart: advertised and received
Local: restart time 10 sec
ipv6-unicast
ipv4-unicast
Remote: restart time 120 sec, notification flag set
ipv4-unicast, forward flag set
4-octet-as: advertised and received
add-path: received
Remote:
ipv4-unicast: receive
enhanced-route-refresh: received
long-lived-graceful-restart: advertised and received
Local:
ipv6-unicast, restart time 10 sec
ipv4-unicast, restart time 20 sec
Remote:
ipv4-unicast, restart time 0 sec, forward flag set
fqdn: advertised and received
Local:
name: donatas-pc, domain:
Remote:
name: spine1-debian-11, domain:
software-version: advertised and received
Local:
GoBGP/3.10.0
Remote:
FRRouting/8.5-dev-MyOwnFRRVersion-gdc92f44a45-dirt
cisco-route-refresh: received
Message statistics:
```
FRR side:
```
root@spine1-debian-11:~# vtysh -c 'show bgp neighbor 192.168.10.17 json' | \
> jq '."192.168.10.17".neighborCapabilities.softwareVersion.receivedSoftwareVersion'
"GoBGP/3.10.0"
root@spine1-debian-11:~#
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
The route-distinguisher string can be expressed in different
ways when the AS number is part of the RD. And the configured
string value has to be kept intact.
The following vty commands store the string value internally:
- router bgp / address-family ipv4 unicast / rd vpn export <>
- router bgp / address-family l2vpn evpn / rd <>
- router bgp / address-family l2vpn evpn / vni <> / rd <>
The vty commands where RD is configured in the below places is
not considered:
- router bgp / rfapi related commands
- router bgp / address-family xxx xxx / network .. rd <>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
RD may be built based on an AS number. Like for the AS, the RD
may use the AS notation. The two below examples can illustrate:
RD 1.1:20 stands for an AS4B:NN RD with AS4B=65536 in dot format.
RD 0.1:20 stands for an AS2B:NNNN RD with AS2B=0.1 in dot+ format.
This commit adds the asnotation mode to prefix_rd2str() API so as
to pick up the relevant display.
Two new printfrr extensions are available to display the RD with
the two above display methods.
- The pRDD extension stands for dot asnotation format
- The pRDE extension stands for dot+ asnotation format.
- The pRD extension has been renamed to pRDP extension
The code is changed each time '%pRD' printf extension is called.
Possibly, the asnotation may change the output, then a macro defines
the asnotation mode to use. A side effect of forging the mode to
use is that the string could not be concatenated with other strings
in vty_out and snprintfrr. Those functions have been called multiple
times. When zlog_debug needs to display the RD with some other string,
the prefix_rd2str() old API is used instead of the printf extension.
Some code has been kept untouched:
- code related to running-config. Actually, wherever an RD is displayed,
its configured name should be dumped.
- bgp rfapi code
- bgp evpn multihoming code (partially done), since the logic is
missing to get the asnotation of 'struct bgp_evpn_es'.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The as-notation mode of the BGP instance will impact the way
the neighbor AS information is dumped in the show commands.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The confederation peers as and the confederation identifier as
are stored as a string to preserve the output in the running
configuration.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This identifier is used to display the peer configuration in
the running-config, like it has been configured.
The following commands are using a specific string attribute:
- neighbor .. remote-as ASN
- neighbor .. local-as ASN
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
A json AS number API is created in order to output a
given AS number. In order to keep backward compatibility,
if the as-notation uses a number, then the json is encoded
as an integer, otherwise the encoding will be a string.
For what is not relevant to running-configuration, the
as-notation mode is the one used for the BGP instance.
Also, the vty completion gets the configured 'as_pretty'
string value, when an user wants to get the available
BGP instances.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
A new keyword permits changing the BGP as-notation output:
- [no] router bgp <> [vrf BLABLA] [as-notation [<dot|plain|dot+>]]
At the BGP instance creation, the output will inherit the way the
BGP instance is declared. For instance, the 'router bgp 1.1'
command will configure the output in the dot format. However, if
the client wants to choose an alternate output, he will have to
add the extra command: 'router bgp 1.1 as-notation dot+'.
Also, if the user wants to have plain format, even if the BGP
instance is declared in dot format, the keyword can also be used
for that.
The as-notation output is only taken into account at the BGP
instance creation. In the case where VPN instances are used,
a separate instance may be dynamically created. In that case,
the real as-notation format will be taken into acccount at the
first configuration.
Linking the as-notation format with the BGP instance makes sense,
as the operators want to keep consistency of what they configure.
One technical reason why to link the as-notation output with the
BGP instance creation is that the as-path segment lists stored
in the BGP updates use a string representation to handle aspath
operations (by using regexp for instance). Changing on the fly
the output needs to regenerate this string representation to the
correct format. Linking the configuration to the BGP instance
creation avoids refreshing the BGP updates. A similar mechanism
is put in place in junos too.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
AS number can be defined as an unsigned long number, or
two uint16 values separated by a period (.). The possible
valus are:
- usual 32 bit values : [1;2^32 -1]
- <1.65535>.<0.65535> for dot notation
- <0.65535>.<0.65535> for dot+ notation.
The 0.0 value is forbidden when configuring BGP instances
or peer configurations.
A new ASN type is added for parsing in the vty.
The following commands use that new identifier:
- router bgp ..
- bgp confederation ..
- neighbor <> remote-as <>
- neighbor <> local-as <>
- clear ip bgp <>
- route-map / set as-path <>
An asn library is available in lib/ and provides some
services:
- convert an as string into an as number.
- parse an as path list string and extract a number.
- convert an as number into a string.
Also, the bgp tests forge an as_zero_path, and to do that,
an API to relax the possibility to have a 0 as value is
specifically called from the tests.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This is a preliminary work to handle various ways to configure
a BGP Autonomous System. When creating a BGP instance, the
user may want to define the AS number as a dotted value,
instead of using an integer value.
To handle both cases, an as_pretty char attribute will store
the as number as it has been given to the vtysh command:
router bgp <as number>
Whenever the as integer of the BGP instance was dumped,
the as_pretty original format is used.
The json output reuses the integer value to keep backward
compatibility with old displays.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The input queue limit does not belong under router bgp. This
is a dev escape and should just be removed.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Consider this scenario:
Lots of peers with a bunch of route information that is changing
fast. One of the peers happens to be really slow for whatever
reason. The way the output queue is filled is that bgpd puts
64 packets at a time and then reschedules itself to send more
in the future. Now suppose that peer has hit it's input Queue
limit and is slow. As such bgp will continue to add data to
the output Queue, irrelevant if the other side is receiving
this data.
Let's limit the Output Queue to the same limit as the Input
Queue. This should prevent bgp eating up large amounts of
memory as stream data when under severe network trauma.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The idea is to drop unwanted attributes from the BGP UPDATE messages and
continue by just ignoring them. This improves the security, flexiblity, etc.
This is the command that Cisco has also.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
For now, if the order was mixed, most of the commands are just silently
ignored. Let the operator notice that.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Some keys are only present in the JSON data of BGP neighbors are only present if the peer is, or has previously been established.
While they are not present if the peer has never come up.
To keep the data structure aligned, the below keys are added also to the neighbors that BGP adjacency has never been established.
Values of the keys are all set to Unknown
hostname:Unknown,
nexthop:Unknown,
nexthopGlobal:Unknown,
nexthopLocal:Unknown,
bgpConnection:Unknown,
Signed-off-by: Karl Quan <kquan@nvidia.com>
When actually creating a peer in BGP, tell the creation if
it is a config node or not. There were cases where the
CONFIG_NODE was being set *after* being placed into
the bgp->peerhash, thus causing collisions between the
doppelganger and the peer and eventually use after free's.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Use %pI4/%pI6 where possible, otherwise at least atjust stack buffer sizes
for inet_ntop() calls.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
currently the following configuration
dut:
!
interface ntfp2
ip router isis 1
!
router bgp 200
no bgp ebgp-requires-policy
bgp confederation identifier 300
bgp confederation peers 300
neighbor 192.168.1.1 remote-as 100
neighbor 192.168.2.2 remote-as 300
!
address-family ipv4 unicast
neighbor 192.168.2.2 default-originate
exit-address-family
!
router isis 1
is-type level-2-only
net 49.0001.0002.0002.0002.00
redistribute ipv4 connected level-2
!
end
router:
!
interface ntfp2
ip router isis 1
isis circuit-type level-2-only
!
router bgp 300
no bgp ebgp-requires-policy
bgp confederation identifier 300
bgp confederation peers 200
neighbor 192.168.2.1 remote-as 200
neighbor 192.168.3.2 remote-as 400
!
address-family ipv4 unicast
network 3.3.3.0/24
exit-address-family
!
router isis 1
is-type level-2-only
net 49.0001.0003.0003.0003.00
redistribute ipv4 connected level-2
!
end
on dut result of show bgp ipv4 unicast command is:
show bgp ipv4 unicast
BGP table version is 1, local router ID is 192.168.2.1, vrf id 0
Default local pref 100, local AS 200
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 192.168.1.1 0 0 100 i
instead of
sho bgp ipv4 unicast
BGP table version is 3, local router ID is 192.168.2.1, vrf id 0
Default local pref 100, local AS 200
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 192.168.1.1 0 0 100 i
*> 3.3.3.0/24 192.168.2.2 0 100 0 (300) i
*> 4.4.4.0/24 192.168.3.2 0 100 0 (300) 400 i
Displayed 3 routes and 3 total paths
According to RFC 5065:the usage of one of the member AS number as the
confederation identifier is not forbidden.
fixes are the following
in bgp_route.c:
in bgp_update remove the test for presence of confederation id in
as_path since, this case is allowed;
in bgp_vty.c
bgp_confederation_peers, remove the test on peer as value
in bgpd.c
bgp_confederation_peers_add
remove the test on peer as value
invert the order of setting peer->sort value and peer->local_as,
since peer->sort is depending from current peer->local_as value
bgp_confederation_peers_remove
invert the order of setting peer->sort value and peer->local_as,
since peer->sort is depending from current peer->local_as value
Signed-off-by: Francois Dumontet <francois.dumontet@6wind.com>
