Add the ability to run a fpm listener to the testing
system. This is nothing more just allowing the test
system to bring it up.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
checkpatch.pl wants you to use ARRAY_SIZE in a kernel
header file. We don't have access to this kernel header
file for normal compilation. I'm just going to remove it.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
If the initial darr capacity is not enough for the output, the `ap` is
reused multiple times, which is wrong, because it may be altered by
`vsnprintf`. Make a copy of `ap` each time instead of reusing.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
We need to operate w/o cryptographic algorithm during key creation
due to how our legacy CLI works (each command issuing a single YANG
modification).
Signed-off-by: Christian Hopps <chopps@labn.net>
This for loop has no chance of removing entries so there is no
need to do a bit of complicated code to handle the case where
an entry can be removed.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
./configure [...] --disable-ripngd
could lead to:
mgmtd/mgmt_vty.c:614:5: warning: "HAVE_RIPNGD" is not defined, evaluates to 0 [-Wundef]
614 | #if HAVE_RIPNGD
| ^~~~~~~~~~~
Signed-off-by: Vincent Jardin <vjardin@free.fr>
When an AS-external-route is deleted on our system and later added again
with a new metric, then the ospfd would first send a LS-update to remove
the old route and later another LS-update to add the route with the new
metric again.
But when this metric-change happens with no time inbetween the ospfd
recognizes this as the same route and does not send any LS-update.
With the change made here, the ospfd will interpret this route as a
different route, when the metric has changed.
Signed-off-by: Alexander Rose <alexander.rose@secunet.com>
Support BMP monitoring for the BGP labeled VPN prefixes.
Signed-off-by: Farid Mihoub <farid.mihoub@6wind.com>
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
This is required by the current (latest/-02 draft).
IANA has registered code 8 for "Send Hold Timer Expired" in the "BGP
Error (Notification) Codes" sub-registry under the "Border Gateway
Protocol (BGP) Parameters" registry.
https://datatracker.ietf.org/doc/html/draft-ietf-idr-bgp-sendholdtimer
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
The following command results in a wrong route-target
display:
> # show running-config
> [..]
> route-map rmap permit 1
> set extcommunity rt 1.45:55
> exit
> router bgp 1.45 as-notation plain
> neighbor 192.0.2.1 remote-as 65500
> address-family ipv4 unicast
> network 192.0.2.2/32 route-map rmap
>
Observed output:
> # show bgp ipv4 192.0.2.2/32
> [..]
> Extended Community: RT:1.0.0.45:55
>
The decoding of the passed cli string assumes this is an
IP address, whereas it is an AS number in dotted format.
Consequently, the vty output will use the ip address encoding.
Count the number of dots in the extended community format.
If a single dot number is detected, the AS format is passed,
and used by the vty output.
After fix:
>
> # show bgp ipv4 192.0.2.2/32
> [..]
> Extended Community: RT:65581:55
>
For remind, AS 65581 and AS 1.45 are a unique AS number.
> show bgp neighbor
> BGP neighbor is 192.0.2.1, remote AS 65500, local AS 65581, external link
> [..]
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Iggy Frankovic discovered an ospfd crash when perfomring fuzzing of OSPF LSA
packets. The crash occurs in ospf_te_parse_te() function when attemping to
create corresponding egde from TE Link parameters. If there is no local
address, an edge is created but without any attributes. During parsing, the
function try to access to this attribute fields which has not been created
causing an ospfd crash.
The patch simply check if the te parser has found a valid local address. If not
found, we stop the parser which avoid the crash.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
