Add to `show zebra` whether or not RA is compiled into FRR
and whether or not BGP is using RFC 5549 at the moment.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The name 'opaque' is a little general - call the route_entry
struct 're_opaque' to make it more specific.
Signed-off-by: Mark Stapp <mstapp@nvidia.com>
Update ospfd and ospf6d to send opaque route attributes to
zebra. Those attributes are stored in the RIB and can be viewed
using the "show ip[v6] route" commands (other than that, they are
completely ignored by zebra).
Example:
```
debian# show ip route 192.168.1.0/24
Routing entry for 192.168.1.0/24
Known via "ospf", distance 110, metric 20, best
Last update 01:57:08 ago
* 10.0.1.2, via eth-rt2, weight 1
OSPF path type : External-2
OSPF tag : 0
debian#
debian# show ip route 192.168.1.0/24 json
{
"192.168.1.0\/24":[
{
"prefix":"192.168.1.0\/24",
"prefixLen":24,
"protocol":"ospf",
"vrfId":0,
"vrfName":"default",
"selected":true,
[snip]
"ospfPathType":"External-2",
"ospfTag":"0"
}
]
}
```
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Add optional NHG ID output to `show ip route` dumps. We have
this in json output already as nexthopGroupID but nice
to have the option in a normal dump as well. Not including in main
output for now to avoid breaking screen scrapers.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
In some cases, zebra may install a nexthop-group id that is
different from the id of the nhe struct attached to a
route-entry. This happens for a singleton recursive nexthop,
for example, where a route is installed with the resolving
nexthop's id.
The installed value is the most useful value - that corresponds
to information in the kernel on linux/netlink platforms that
support nhgs. Display both values if they differ in ascii
output, and include both values in the json form.
Signed-off-by: Mark Stapp <mstapp@nvidia.com>
```
exit1-debian-9# show ip route 172.16.16.1/32
Routing entry for 172.16.16.1/32
Known via "bgp", distance 20, metric 0, best
Last update 00:00:28 ago
* 192.168.0.2, via eth1, weight 1
AS-Path : 65003
Communities : first 65001:2 65001:3
Large-Communities: 65001:1:1 65001:1:2 65001:1:3
Selection reason : First path received
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
PIM is going to need to be able to send down the address it is
trying to resolve in the multicast rib. We need a way to signal
this to the end developer. Start the conversion by adding the
ability to have a safi. But only allow SAFI_UNICAST at the moment.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The entirety of the import checking no longer needs to be
in zebra as that no-one is calling it. Remove the code.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Because vrf backend may be based on namespaces, each vrf can
use in the [16-(2^32-1)] range table identifier for daemons that
request it. Extend the table manager to be hosted by vrf.
That possibility is disabled in the case the vrf backend is vrflite.
In that case, all vrf context use the same table manager instance.
Add a configuration command to be able to configure the wished
range of tables to use. This is a solution that permits to give
chunks to bgp daemon when it works with bgp flowspec entries and
wants to use specific iptables that do not override vrf tables.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
We should not be using `case default` with an enumerated type
This prevents the developer of new cases from knowing where
they need to fix by just compiling.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Description:
Change is intended for fixing the following issues related to vrf route leaking:
Routes with special nexthops i.e. blackhole/sink routes when imported,
are not programmed into the FIB and corresponding nexthop is set as 'inactive',
nexthop interface as 'unknown'.
While importing/leaking routes between VRFs, in case of special nexthop(ipv4/ipv6)
once bgp announces route(s) to zebra, nexthop type is incorrectly set as
NEXTHOP_TYPE_IPV6_IFINDEX/NEXTHOP_TYPE_IFINDEX
i.e. directly connected even though we are not able to resolve through an interface.
This leads to nexthop_active_check marking nexthop !NEXTHOP_FLAG_ACTIVE.
Unable to find the active nexthop(s), route is not programmed into the FIB.
Whenever BGP leaks routes, set the correct nexthop type, so that route gets resolved
and correctly programmed into the FIB, in the imported vrf.
Co-authored-by: Kantesh Mundaragi <kmundaragi@vmware.com>
Signed-off-by: Iqra Siddiqui <imujeebsiddi@vmware.com>
Basically, this is handled by JSON-C library. I've compiled with the
latest release of json-c and it works well.
Didn't test with various distribution versions, but this change is kinda
dependend from the json-c lib version the distra has.
Before:
```
"192.168.100.1\/32":[
{
"prefix":"192.168.100.1\/32",
```
After:
```
"192.168.100.1/32":[
{
"prefix":"192.168.100.1/32",
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
With this patch, zclient can intall seg6 rotues when
they set properties "nh_seg6_segs" on struct nexthop
and set ZEBRA_FLAG_SEG6_ROUTE on zapi_route's flag.
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
With this patch, zclient can intall seg6local rotues whem
they set properties nh_seg6local_{action,ctx} on struct nexthop
and set ZEBRA_FLAG_SEG6LOCAL_ROUTE on zapi_route's flag.
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
This includes community and large-community data.
```
exit1-debian-9# show ip route 172.16.16.1/32
Routing entry for 172.16.16.1/32
Known via "bgp", distance 20, metric 0, best
Last update 00:00:23 ago
* 192.168.0.2, via eth1, weight 1
AS-Path : 65030
Communities : 65001:1 65001:2 65001:3 65001:4 65001:5 65001:6
Large-Communities: 65001:123:1 65001:123:2
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Description:
Added a new show command("show ip zebra route dump") to dump all routes
with detailed information including nexthops,flags, status ..etc.
This helps for dubugging and added to support_bundle_command.conf.
Defined this command as a hidden command.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Add uptime for use with NHEs to keep track of how
long we have had this NHE in our rib without an update.
This is treated exactly the same as the re->uptime for
routes. When we get an update for a route, we reset the
uptime.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
