Anycast requires that the lo interface be associated with multiple
addresses. One is the anycast IP address (which is the same on all RPs
participating in RP redundancy) and the second is the unique IP address
that will be used as the router id by routing protocols.
To accomodate that we maintain a list of secondary addresses per-pim iface
and allow any of them to be the RP address. This lets the I_am_RP macro
succeed on anycast RPs.
Note that the support is limited i.e. we don't actually advertise a
secondary list to the neighbors. This is assuming the anycast IP will never
be used as a router id i.e. will never be an RPF neighbor.
Sample output:
==============
dell-s6000-04# sh ip pim interface lo
Interface : lo
State : up
Address : 100.1.1.1 (primary)
100.1.1.2
100.1.1.3
100.1.2.1
>>>>>>> SNIP >>>>>>>>>>>>>>>
dell-s6000-04# sh ip pim interface lo json
{
"lo":{
"name":"lo",
"state":"up",
"address":"100.1.1.1",
"index":1,
"lanDelayEnabled":true,
"secondaryAddressList":[
"100.1.1.2",
"100.1.1.3",
"100.1.2.1"
],
>>>>>>> SNIP >>>>>>>>>>>>>>>
dell-s6000-04#sh ip pim rp-info
RP address group/prefix-list OIF I am RP
100.1.2.1 224.0.0.0/4 lo yes
dell-s6000-04#
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
Debugs are extremely expensive currently. Let's
store 'struct prefix_sg sg' string format in
the ifchannel, upstream and msdp_sa structures.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
1. This is needed to layout the MSDP macros for determining what SAs are
originated by a MSDP speaker.
2. We no longer let the kat timer expire on an active flow. Activity
counters/lastuse is polled via a wheel for every SG entry. If new
activity is detected the keepalive timer is started and SPT bit set.
A SRC_STREAM reference is also created for the entry if one doesn't
already exist.
3. If KAT actually expires it means the flow is no longer active. At
this point we stop advertising the SA to MSDP peers. We also pull
the SRC_STREAM reference (deleting the entry if there are no other
references).
PS: Checking counters on KAT expiry will come in the next change.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add the 'ip pim register-suppress-time ...' command.
Remove the 'no ip pim rp keep-al...' command as
that the register suppress set that value.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we receive a 'no ip pim sm' for an interface
that has both pim and igmp on it, only turn
off pim.
Ticket: CM-12985
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
1. Add support for mesh-group based configuration that is easy to apply
via automation. The older per-peer configuartion is temporarily hidden
and will be cleaned up later.
Sample config -
ip msdp mesh-group cumulus source 100.1.1.4
ip msdp mesh-group cumulus member 100.1.1.5
ip msdp mesh-group cumulus member 100.1.1.6
2. Added support for detail peer and sa-cache displays. Along with
filter keys.
3. Add json output for all the msdp displays.
With this commit basic support for anycast-RP with MSDP (in numbered
network is complete). Unnumbered support will be added separately.
Ticket: CM-13306
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
1. Added a new MSDP source reference flag for creating (S,G) entries
based on the SA-cache. The RFC recommends treating as SA like rxing
a (S, G) join (which is a bit different then treating like a traffic
stream).
2. SA-SPT is only setup if we are RP for the group and a corresponding
(*,G) exists with a non-empty OIL.
3. When an SA is moved we need to let the SPT live if it is active (this
change will come in a subsequent CL).
Testing done:
1. SA first; SPT setup whenever (*, G) comes around.
2. (*, G) first. As soon as SA is added SPT is setup.
3. (*, G) del with valid SA entries around.
Ticket: CM-13306
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we have multiple incoming joins for
a single group on a interface, we need to
allow proper output.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If you add to the json by grp, if you have multiple
ifchannels for that group, on the the first one will
be displayed.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This commit includes -
1. Maintaining SA cache with local and remote entries.
2. Local SA entries - there are two cases where we pick up these -
- We are RP and got a source-register from the FHR.
- We are RP and FHR and learnt a new directly connected source on a
DR interface.
3. Local entries are pushed to peers immediately on addition and
periodically. An immediate push is also done when peer session is
established.
4. Remote SA entries - from other peers in the mesh group and passed
peer-RPF checks.
5. Remote entries are aged out. No other way to del them
currently. In the future we may add a knob to flush entries on
peer-down.
Testing done -
Misc topologies with CL routers plus basic interop with another vendor (
we can process their SA updates and they ours).
Sample output -
root@rp:~# vtysh -c "show ip msdp sa"
Source Group RP Uptime
33.1.1.1 239.1.1.2 local 00:02:34
33.1.1.1 239.1.1.3 local 00:02:19
44.1.1.1 239.1.1.4 100.1.3.1 00:01:12
44.1.1.1 239.1.1.5 100.1.3.1 00:00:55
root@rp:~#
Ticket: CM-13306
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
This fix handles two issues:
1) Searching entire vrf_iflist to get per interface pim_ifchannel_list
2) Display of ifchannel information in pim not being ordered correctly.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This commit includes the following changes -
1. Support for MSDP peer DB (hash and sorted list).
2. Support for the following timers - keepalive, connect-retry, hold.
3. TCP session management (lower-ip is active, higher-ip is passive).
4. MSDP KA packet rx/tx.
5. Limited temporary config (will be replaced with the more automation
friendly RP-set).
Testing done -
Peer bringup/deletion (including interop with another vendor)
Sample out -
root@dell-s6000-04:~# sudo vtysh -c "show ip msdp peer"
Peer Local Mesh-group State Uptime
100.1.1.1 100.1.2.1 default established 00:07:27
100.1.3.1 100.1.2.1 default established 00:31:50
root@dell-s6000-04:~#
Coming soon -
1. part-2: SA cache management.
2. part-3: SPT setup using source in SA cache.
3. part-4: CLI cleanup.
Ticket: CM-13306
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
The test commands are not being maintained and
are not out of date with the rest of the system. There
are better ways to test code and in addition these
commands if entered by a user could seriously impact
their running system.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Cache the last time we looked up the nexthop for this particular
address. Store time to usec accuracy.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
This cleans up the following so that they always collect the data to
display in json structures and then either dumps the json output or
traverses it to produce the non-json output.
show ip pim local-membership
show ip pim interface
When entering debug commands under 'conf t' mode
allow the debugs to be saved for future fun and
adventure.
Ticket: CM-13213
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When looking up the channel_oil use a hash
to find it. Keep the list around for quick
walks of the channel oils.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Pim sometimes needs the upstream rpf lookup to
only take into account if we have a nbr out
the selected interface or not. Move
the code for this to a better spot so
we can make a more intelligent decision
here.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
mrib_nexthop_addr and rpf_addr should be 'struct prefix'
so that we can safely handle unnumbered data from a nexthop
lookup in zebra
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
List the RP information we have configured.
Fix bug where we were not properly initializing some code
Ticket: CM-12617
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
I tried to be smart and skirt around rpf lookup if I knew
the incoming interface. This turns out to be not necessarily
a good thing because we can easily have asymetrical routing.
This fix removes the attempt to cache the ifp we received
the incoming packet on and just lets the lookup work like
it should.
Additionally it removes the weird hardcoding of the rpf
interface from the register stuff.
Ticket: CM-12530
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
reb
Just pass in the actual state to allow us to translate
the state to a string even if we don't have a upstream.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When there is allot of IGMP activity for the
kernel upcall that we are ignoring, just
ignore it for the moment as well.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow the user to specify multiple rp commands.
'ip pim rp A.B.C.D' -> translates to 'ip pim rp A.G.C.D 224.0.0.0/24'
ip pim rp A.B.C.D A.B.C.D/M
First is the rp, second is the group with mask.
Groups and masks cannot be over each other except 224.0.0.0/24 which
is the fallback if used.
Ticket: CM-7860
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
