EVPN is only enabled when user configures advertise-all-vni.
All VNIs (L2 and L3) should be cleared upon removal of this config.
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
For EVPN type-5 route the NH in the NLRI is set to the local tunnel ip.
This information has to be obtained from kernel notification.
We need to pass this info from zebra to bgp in l3vni call flow.
This patch doesn't handle the tunnel-ip change.
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
When a remote VTEP next hop entry (for symmetric routing) becomes
stale, reinstall it. This makes the behavior the same as what is
done for remote host next hops (for asymmetric routing and ARP
suppression).
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Upon a l3vni delete (no vni under a vrf) is executed,
we should uninstall all the RMACs and NHs associated with the l3vni.
This is because by the time we get a route delete in zebra
l3vni is already deleted and we dont have refernce to RMACs and NHs
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
As netlink is available for all linux systems ( old linux distributions
are not considered), this commit removes the ipv6 ioctl support for
linux.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
It is possible to configure IPv6 addresses from interfaces by using
netlink socket, intead of using standard sockets.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
zserv.c had a grab bag of function declarations that
did not belong in it. Move those to where they better
belong.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
zserv.c has become a bit of a dumping ground for zebra cli.
I'd like to focus the zserv.c code into it's core functionality
which is handling the zapi interface.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The zebrad initialization does not need to be part of cli
initialization and should be done separately.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If the frr.conf file contains bgp unnumbered peering but the associated
interfaces do not have the commands "no ipv6 nd suppress-ra" and
"ipv6 nd ra-interval 10" configured, when frr-reload.py is issued the
interface commands are removed from the running config, causing peers to
got down and stay down after a link flap. This situation can occur if
the frr.conf file is created manually or via automation (like ansible)
but a subsequent "wr mem" has not been performed.
This fix changes the behavior so that the interface ipv6 nd ra commands
created by bgp are not displayed. Therefore, when the above condition
occurs, there is no difference between the running and stored configs
and peers work fine.
Ticket: CM-18702
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: CCR-7004
Testing-done: Manual testing successful. L3-smoke has no new failures
When we get a STREAM_GET failure of some sort we
need to handle the failure case here and safely
free up stored memory/context and return gracefully.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Some of the deprecated stream.h macros see such little use that we may
as well just remove them and use the non-deprecated macros.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
In some circumstances zebra and ldpd would display a pseudowire as UP
when in reality it's not (example: MTU mismatch between the two ends). Fix
this to avoid confusion.
Reported-by: ßingen <bingen@voltanet.io>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
When doing a route replace, on openbsd we were not
marking the old lsp as no longer installed, while
on linux we were. Move the abstraction up a layer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Setup a interface such that the add/del of lsp's from
the kernel can have a callback for success/failure.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When a route is installed or deleted into the kernel allow a
callback mechanism to handle the success/failure of
the kernel call.
This separation is to allow us to do these things:
1) In the future create a true pthread to handle route
install/deletes. This way we can schedule these
events in a smarter fashion
2) Allow us to use a common southbound api for route
install and deletion.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
