When executing the following command to change the NSSA translator role
from OSPF_NSSA_ROLE_ALWAYS to OSPF_NSSA_ROLE_NEVER
r2(config-router)# area 1 nssa translate-never
During the time the `ospf_abr_nssa_check_status()` function is not executed,
we are in a situation where the role is OSPF_NSSA_ROLE_NEVER (just configured)
but the NSSATranslatorState is still ENABLED
During this time the output of "show ip ospf" displays the following:
r2# show ip ospf
Area ID: 0.0.0.1 (NSSA)
Shortcutting mode: Default, S-bit consensus: no
Number of interfaces in this area: Total: 1, Active: 1
It is an NSSA configuration.
Elected NSSA/ABR performs type-7/type-5 LSA translation.
We are an ABR and Number of fully adjacent neighbors in this area: 1 (**)
Basically the case TranslatorState=ENABLED && TranslatorRole=ROLE_NEVER is not
covered in `ospf_vty.c`
This PR adds the case TranslatorState=ENABLED and TranslatorRole=ROLE_NEVER
which should only happen for a small period of time
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
The test_bgp_multi_vrf_topo2.py script had a bunch
of places where it would change an interface status
or add delete routes that would affect bgp convergence
but it was never ensuring that convergence had happened
before the test verified the bgp rib. I believe this
was leading to many intermittant ci failures in
testing for other PR's to be accepted. Modify
the code to wait for bgp convergence if we just
made a change to the topology
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Currently if you start ospfd, bring up neighbors and then issue
a tcpdump on a interface ospf is peering over, this causes the neighbor
relationship to be restarted:
root@spectrum301(mlx-4600c-01):mgmt:~# tcpdump -i vlan402
2020-11-13T21:25:38.059671+00:00 spectrum301 ospfd[29953]: AdjChg: Nbr 202.0.0.3(default) on vlan402:200.0.3.1: Full -> Deleted (KillNbr)
2020-11-13T21:25:38.065520+00:00 spectrum301 ospfd[29953]: ospfTrapNbrStateChange: trap sent: 200.0.3.2 now Deleted/DROther
2020-11-13T21:25:38.065922+00:00 spectrum301 ospfd[29953]: ospfTrapIfStateChange: trap sent: 200.0.3.1 now Down
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on vlan402, link-type EN10MB (Ethernet), capture size 262144 bytes
21:25:38.072330 IP 200.0.3.1 > igmp.mcast.net: igmp v3 report, 1 group record(s)
2020-11-13T21:25:38.080430+00:00 spectrum301 ospfd[29953]: ospfTrapIfStateChange: trap sent: 200.0.3.1 now Point-To-Point
2020-11-13T21:25:38.080654+00:00 spectrum301 ospfd[29953]: SPF Processing Time(usecs): 9734
2020-11-13T21:25:38.080829+00:00 spectrum301 ospfd[29953]: SPF Time: 6422
2020-11-13T21:25:38.080991+00:00 spectrum301 ospfd[29953]: InterArea: 1572
2020-11-13T21:25:38.081152+00:00 spectrum301 ospfd[29953]: Prune: 67
2020-11-13T21:25:38.081329+00:00 spectrum301 ospfd[29953]: RouteInstall: 1396
2020-11-13T21:25:38.081548+00:00 spectrum301 ospfd[29953]: Reason(s) for SPF: N, S, ABR, ASBR
21:25:38.092510 IP 200.0.3.1 > ospf-all.mcast.net: OSPFv2, Hello, length 44
This is happening because the curr_mtu is not being properly stored. It was being set
on interface creation( but we have not actually read in the mtu part of the interface data, so
it is still 0 ).
Modify the code to store the curr_mtu at a point in interface creation *After* we have read
in interface data.
Ticket: CM-32276
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
OSPF instance initialization was moved from "router ospf" vty command to
ospf_get function some time ago but the same thing must be done in
ospf_get_instance function used when multi-instance mode is enabled.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
The following virtual-link configuration was not represented in the
running configuration:
area <area> virtual-link <ip> authentication [null|message-digest]
Signed-off-by: Duncan Eastoe <duncan.eastoe@att.com>
A MAC entry cannot be deleted while a neigh is referencing it. It seems
there is some race condition where this may be happening. The log is
to help identify those cases.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
It is now 4bits of type and 28bits of value -
1. type=0 is for L3 NHG
2. type=1 is for L2 NH
3. type=2 is for L2 NHG
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
This is an optimization to reduce the number of L2 nexthops. A
l2 or fdb nexthop simply provides the dataplane with a nexthop ip-
torm-12:mgmt:~# ip nexthop
id 268435461 via 27.0.0.20 scope link fdb
id 268435463 via 27.0.0.20 scope link fdb
id 268435465 via 27.0.0.20 scope link fdb
So there is no need to allocate a nexthop per-ES/per-VTEP. There
can be 100+ ESs per-VTEP so this change cuts the scale down by a
factor of 100.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
When a local ES flaps there are two modes in which the local
MACs are failed over -
1. Fast failover - A backup NHG (ES-peer group) is programmed in the
dataplane per-access port. When a local ES flaps the MAC entries
are left unaltered i.e. pointing to the down access port. And the
dataplane redirects traffic destined to the oper-down access port
via the backup NHG.
2. Slow failover - This mode needs to be turned on to allow dataplanes
not capable of re-directing traffic. In this mode local MAC entries
on a down local ES are re-programmed to point to the ES-peers'
NHG. And vice-versa i.e. when the ES comes up the MAC entries
are re-programmed with the access port as dest.
Fast failover is on by default. Slow failover can be enabled via the
following config -
evpn mh redirect-off
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
As a part of extended MM handing a MAC can be updated from local
to remote while being referenced by SYNC neighs (this is really a
temporary/small window). During this window if the MAC transitions
back to local again we need to re-inforce the previous SYNC flags
(based on the sync-neigh count) as subsequent SYNC updates to the
MAC will be de-duped and ignored.
Ticket: CM-29636
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
When a local mac is deleted by the dataplane zebra can re-install it
if the MAC is a SYNC MAC (learned from ES peers). The "local_inactive"
bit must be set as a part of the re-install to prevent zebra turning
around and advertising the MAC as locally active.
Also fixed up some debug logs in the slow-fail path to include the VNI.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
NHG and DST (VTEP-IP) are mutually exclusive attributes. If DST is
present the kernel ignores NHG.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
NHG is activated i.e. programmed in the dataplane only if there
are active-VTEPs associated with it. When a NHG is de-activated
all the remote-mac entries associated with it need to be removed
before the NHG is removed.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
The lookup for non default VRFs was always using a tableId; if not
provided, we were defaulting to RT_TABLE_MAIN. This is fine for the
default VRF but not for others. As a result, the command was silently
failing for non-default VRFs unless we also specified the correct tableId.
Fix this by only performing the lookup using the tableId if it is
provided; else use zebra_vrf_table.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
A couple NHG messages we were logging as errors are a bit spammy
in usecases where you routinely add/remove interfaces (VM heavy
deployments). Its not really an error a user cares about and
more for a developer to know what went wrong after the fact so
it makes more sense for these to be under a debug rather than
an error since seeing them does not implicitly mean error during
those usecases.
Signed-off-by: Stephen Worley <sworley@nvidia.com>
Issue:
Configure msdp mesh mg1 for 2 groups.
ip msdp mesh-group mg1 member 1.1.1.1
ip msdp mesh-group mg1 member 1.1.1.2
Remove mg1 for 1.1.1.1
no ip msdp mesh-group mg1 member 1.1.1.1
mg1 for 1.1.1.1 still present. This is fixed.
Signed-off-by: Sarita Patra <saritap@vmware.com>
Issue:
Configure RP.
ip pim rp 20.0.0.1 239.1.1.1/32
ip pim rp 20.0.0.1 239.1.1.2/32
Remove RP.
no ip pim rp 20.0.0.1 239.1.1.1/32
Rp is not removed. This is fixed now.
Signed-off-by: Sarita Patra <saritap@vmware.com>
The pim_version.[c|h] files are never used and we are getting
warnings about PIM_VERSION changing pointer sizes from
newer versions of the compiler. I see no reason to keep this
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
