Removing the obsolete ldp-sync periodic 'hello' message.
When ldp-sync is configured, IGPs take action if the LDP process goes down.
The IGPs have been updated to use the zapi client close callback to detect
the LDP process going down.
Signed-off-by: Karen Schoener <karen@voltanet.io>
When ldp-sync is configured, IGPs take action if the LDP process goes down.
Currently, IGPs detect the LDP process is down if they do not receive a
periodic 'hello' message from LDP within 1 second.
Intermittently, this heartbeat mechanism causes false topotest failures.
When the failure occurs, LDP is busy receiving messages from zebra for a
few seconds. During this time, LDP does not send the expected periodic
message.
With this change, IGPs detect LDP down via zapi client close message.
Signed-off-by: Karen Schoener <karen@voltanet.io>
When executing the following command to change the NSSA translator role
from OSPF_NSSA_ROLE_ALWAYS to OSPF_NSSA_ROLE_NEVER
r2(config-router)# area 1 nssa translate-never
During the time the `ospf_abr_nssa_check_status()` function is not executed,
we are in a situation where the role is OSPF_NSSA_ROLE_NEVER (just configured)
but the NSSATranslatorState is still ENABLED
During this time the output of "show ip ospf" displays the following:
r2# show ip ospf
Area ID: 0.0.0.1 (NSSA)
Shortcutting mode: Default, S-bit consensus: no
Number of interfaces in this area: Total: 1, Active: 1
It is an NSSA configuration.
Elected NSSA/ABR performs type-7/type-5 LSA translation.
We are an ABR and Number of fully adjacent neighbors in this area: 1 (**)
Basically the case TranslatorState=ENABLED && TranslatorRole=ROLE_NEVER is not
covered in `ospf_vty.c`
This PR adds the case TranslatorState=ENABLED and TranslatorRole=ROLE_NEVER
which should only happen for a small period of time
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
Currently if you start ospfd, bring up neighbors and then issue
a tcpdump on a interface ospf is peering over, this causes the neighbor
relationship to be restarted:
root@spectrum301(mlx-4600c-01):mgmt:~# tcpdump -i vlan402
2020-11-13T21:25:38.059671+00:00 spectrum301 ospfd[29953]: AdjChg: Nbr 202.0.0.3(default) on vlan402:200.0.3.1: Full -> Deleted (KillNbr)
2020-11-13T21:25:38.065520+00:00 spectrum301 ospfd[29953]: ospfTrapNbrStateChange: trap sent: 200.0.3.2 now Deleted/DROther
2020-11-13T21:25:38.065922+00:00 spectrum301 ospfd[29953]: ospfTrapIfStateChange: trap sent: 200.0.3.1 now Down
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on vlan402, link-type EN10MB (Ethernet), capture size 262144 bytes
21:25:38.072330 IP 200.0.3.1 > igmp.mcast.net: igmp v3 report, 1 group record(s)
2020-11-13T21:25:38.080430+00:00 spectrum301 ospfd[29953]: ospfTrapIfStateChange: trap sent: 200.0.3.1 now Point-To-Point
2020-11-13T21:25:38.080654+00:00 spectrum301 ospfd[29953]: SPF Processing Time(usecs): 9734
2020-11-13T21:25:38.080829+00:00 spectrum301 ospfd[29953]: SPF Time: 6422
2020-11-13T21:25:38.080991+00:00 spectrum301 ospfd[29953]: InterArea: 1572
2020-11-13T21:25:38.081152+00:00 spectrum301 ospfd[29953]: Prune: 67
2020-11-13T21:25:38.081329+00:00 spectrum301 ospfd[29953]: RouteInstall: 1396
2020-11-13T21:25:38.081548+00:00 spectrum301 ospfd[29953]: Reason(s) for SPF: N, S, ABR, ASBR
21:25:38.092510 IP 200.0.3.1 > ospf-all.mcast.net: OSPFv2, Hello, length 44
This is happening because the curr_mtu is not being properly stored. It was being set
on interface creation( but we have not actually read in the mtu part of the interface data, so
it is still 0 ).
Modify the code to store the curr_mtu at a point in interface creation *After* we have read
in interface data.
Ticket: CM-32276
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
OSPF instance initialization was moved from "router ospf" vty command to
ospf_get function some time ago but the same thing must be done in
ospf_get_instance function used when multi-instance mode is enabled.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
The following virtual-link configuration was not represented in the
running configuration:
area <area> virtual-link <ip> authentication [null|message-digest]
Signed-off-by: Duncan Eastoe <duncan.eastoe@att.com>
Commit: 1d376ff539 removed
the code to find nexthops for the POINTOMULTIPOINT and
replaced it with a generic bit of code that was
supposed to handle both POINTOPOINT and POINTOMULTIPOINT
the problem is that the ospf rfc states that the
network mask on point to multipoint should be /32
which will not allow you to properly do a prefix match
on it against the network.
Restore original behavior as much as possible and leave
the new POINTOPOINT code alone.
Fixes: #7624
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When allocating memory for the `struct ospf_metric` we
were using `uint32_t` instead of the actual size of this
structure. When we wrote to it we would be writing
into other people's memory.
Found-by: Amol Lad
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When an ABR NSSA router is configured to be ALWAYS the translator:
r22(config-router)# area 1 nssa translate-always
It will advertise this condition in the type-1 LSA setting the Nt
bit, taking over the translator role from r33
r22# show ip ospf
We are an ABR and always an NSSA Translator.
r33# show ip ospf
We are an ABR, but not the NSSA Elected Translator.
However when the command above is removed:
r22(config-router)# no area 1 nssa translate-always
the bit Nt needs to be cleared otherwise we end up with no translator
in the area
r22# show ip ospf
We are an ABR, but not the NSSA Elected Translator.
r33# show ip ospf
We are an ABR, but not the NSSA Elected Translator.
This PR forces the ABR to send a type-1 LSA with the Nt bit updated
according to the translator role
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
Having 2 ABR in NSSA area where R3 is the elected translator
R3# show ip ospf
We are an ABR and the NSSA Elected Translator.
R2# show ip ospf
We are an ABR, but not the NSSA Elected Translator.
When R3 loses the Border condition by shutting down the interface
to the backbone, we end up with no translator in the NSSA area. It
is expected R2 to take over the translator role
R3# sh ip ospf
It is not ABR, therefore not Translator.
R2# show ip ospf
We are an ABR, but not the NSSA Elected Translator.
This PR forces the ABR to reevaluate the translator condition, so
R2 becomes the elected Translator
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
This commits attempts to fix a problem that occurs when mpls-te gets
removed from ospfd config. Mpls-te has an inter-as option, which can be
set to Off/Area/AS. Whenever the inter-as takes "Area" or "AS" as a
value, this value will not be cleaned after removing mpls-te or after
removing the ospf router. Therefore, if mpls-te is configured with
inter-as AS or Area and we remove mpls-te or the ospf router, the
inter-as will still preserve its value; therefore, next time mpls-te is
enabled, it will automatically inherits the previous inter-as value
(either Area or AS). This leads to wrong configuration, which can be a
problem for frr_reload.py.
The commits forces mpls-te to reset inter-as to Off before it mpls-te
gets removed from the configuration and before the ospf router gets
removed.
Signed-off-by: Carlo Galiotto <carlo@voltanet.io>
The `enum zclient_send_status` enum needs to be extended
throughout the code base to use the new states and
to fix up places where we tested against the return
value being non zero.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The route_map_object_t was being used to track what protocol we were
being called against. But each protocol was only ever calling itself.
So we had a variable that was only ever being passed in from route_map_apply
that had to be carried against and everyone was testing if that variable
was for their own stack.
Clean up this route_map_object_t from the entire system. We should
speed some stuff up. Yes I know not a bunch but this will add up.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
gcc 10 complains about some of our format specs, fix them. Use
atomic size_t in thread stats, to work around platform
differences.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
This commit tells the compiler we are intentionally ignoring
the lsa value returned and not doing anything with ret.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Description:
The below show command introduced to diplay all configured
summary addresss information along with matching corresponding
external route information.
show ip ospf [vrf <NAME|all>] summary-address [detail] [json]
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Description:
Apis for creating/deleting aggregate routes.
Origination of summary route on behalf of matched external routes.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Description:
Summarisation initilisation and de-init apis.
summary route table will be created as part of initilisation
at the time of ospf deamon init.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Description:
Added json support to ospf lsdb command and its subcommands.
Added json to the following sub commands.
show ip ospf database json
show ip ospf database router json
show ip ospf database network json
show ip ospf database external json
show ip ospf database summary json
show ip ospf database asbr-summary json
show ip ospf database nssa-external json
show ip ospf databas max-age json
show ip ospf database self-originate json
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Issue:
When the ospf area is changed from default to nssa or stub, the previously
advertised external LSAs are not removed from the neighbor.
The LSAs remain in database till maxage timeout.
Fix:
Advertise the external LSAs with age set to maxage and flood to the
nssa or stub area.
Signed-off-by: kssoman <somanks@gmail.com>
When Segment Routing is not enabled, some related output messages are
printed on the console especially when Segment Routing Debug is enabled.
This patch adds additional controls to check whether segment routing
is enabled or not.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Replace all lib/thread cancel macros, use thread_cancel()
everywhere. Only the THREAD_OFF macro and thread_cancel() api are
supported. Also adjust thread_cancel_async() to NULL caller's pointer (if
present).
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Change thread_cancel to take a ** to an event, NULL-check
before dereferencing, and NULL the caller's pointer. Update
many callers to use the new signature.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
