The tests work with the default settings of BFD meaning that bfdd is
able to recognize a 'down' link after ~900ms so a route recovery should
be visible in the RIB after 1 second.
In the current state only IPv4 is used (when using IPv6
autoconfiguration) within BFD, even though the recovery also affects
IPv6 routes. This is different to the current state of ospfd/ospf6d in
combination with BFD since both IPv4 and IPv6 sessions are used there.
The following topology is used:
+---------+
| |
eth-rt2 (.1) | RT1 | eth-rt3 (.1)
+----------+ 1.1.1.1 +----------+
| | | |
| +---------+ |
| |
| 10.0.2.0/24 |
| |
| eth-rt1 | (.2)
| 10.0.1.0/24 +----+----+
| | |
| | RT3 |
| | 3.3.3.3 |
| | |
(.2) | eth-rt1 +----+----+
+----+----+ eth-rt4 | (.1)
| | |
| RT2 | |
| 2.2.2.2 | 10.0.4.0/24 |
| | |
+----+----+ |
(.1) | eth-rt5 eth-rt3 | (.2)
| +----+----+
| | |
| | RT4 |
| | 4.4.4.4 |
| | |
| +----+----+
| 10.0.3.0/24 eth-rt5 | (.1)
| |
| |
| 10.0.5.0/24 |
| |
| +---------+ |
| | | |
+----------+ RT5 +----------+
eth-rt2 (.2) | 5.5.5.5 | eth-rt4 (.2)
| |
+---------+
Route recovery is tested on RT1. The focus here lies on the two
different routes to RT5. Link failures are generated by taking
down interfaces via the mininet Python interface on RT2 and RT3.
Hence routes are supposed to be adjusted to use RT3 when a link
failure happens on RT2 or vice versa.
Note that only failure recognition and recovery is "fast". BFD
does not monitor a link becoming available again.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
Segment Routing Local Block (SRLB) is part of RFC8667. This change introduces
the possibility for isisd to advertize SRLB in LSP. Base and Range of SRLB
could be configured through CLI or Yang.
Adjacency-SID are now using this SRLB for label allocation. SRLB could also
be used for SID-Binding (e.g. LDP to SR).
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
A new config option `--disable-version-build-config`
allows you to show short version string by dropping
"configured with:" and all of its build configs
Signed-off-by: Jafar Al-Gharaibeh <jafar@atcorp.com>
Distinguish between unicast and broadcast opaque messages
in zebra handler code. Add cli and internal api changes to
have sharpd send unicast opaque messages. Add opaque cli
commands to the sharp user doc.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Description:
Added json support for the following PIM commands.
1. show ip mroute [vrf NAME] count [json]
2. show ip mroute vrf all count [json]
3. show ip mroute [vrf NAME] summary [json]
4. show ip mroute vrf all summary [json]
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Let the user know its possible to create BFD sessions with profiles
applied to it or apply profile to already created sessions.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Updated documentation for routers with a large route table, which breaks
SNMP/AgentX and in some conditions even crashes FRR. The documentation
proposal amends the SNMP configuration to exclude certain OID's that
are not needed in normal cases.
Format-fixed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Bart Vrancken <bart@abuse.io>
Revise new `show pbr` keys to be consistent with existing
json in other daemons
target->nexthop
id->tableId (where relevant)
isValid->valid
isInstalled->installed
Signed-off-by: Wesley Coakley <wcoakley@cumulusnetworks.com>
a linux configuration gives some explanation on how to set up an evpn
overlay in network namespaces.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Include an IPv6 example for set src
And a note that the IP address has to exist. This is to try and make
people aware to avoid things like issue #4249https://github.com/FRRouting/frr/issues/4249
Signed-off-by: Tim Bray <tim@kooky.org>
