if r1 has a route received from a neighbor with the default administrative
distance configured
r1# sh ip route
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR,
f - OpenFabric,
> - selected route, * - FIB route, q - queued, r - rejected, b - backup
t - trapped, o - offload failure
O>* 1.1.1.1/32 [110/20] via 10.0.12.2, r1-r2-eth0, weight 1, 00:00:41
if we change the administrative distance
r1(config)# router ospf
r1(config-router)# distance 50
this is not applied as there are no changes in the routing table
r1# sh ip route
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR,
f - OpenFabric,
> - selected route, * - FIB route, q - queued, r - rejected, b - backup
t - trapped, o - offload failure
O>* 1.1.1.1/32 [110/20] via 10.0.12.2, r1-r2-eth0, weight 1, 00:00:13
This commit will force the update of the routing table with the new configured distance
r1# sh ip route
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR,
f - OpenFabric,
> - selected route, * - FIB route, q - queued, r - rejected, b - backup
t - trapped, o - offload failure
O>* 1.1.1.1/32 [50/20] via 10.0.12.2, r1-r2-eth0, weight 1, 00:00:14
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
Two minor fixes:
- remove redundant "(a.b.c.d/m)" in "prefix" description
- remove some annoying space in "summary-address" and "tag"
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Currently "range" command can only accept `cost` or `substitute`
individually, and `show running` will mix them.
So need make it accept mixed form with both of them, otherwise
configuration file in mixed form will fail to start.
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Opaque data takes up a lot of memory when there are a lot of routes on
the box. Given that this is just a cosmetic info, I propose to disable
it by default to not shock people who start using FRR for the first time
or upgrades from an old version.
Fixes#10101.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
VRF name should not be printed in the config since 574445ec. The update
was done for NB config output but I missed it for regular vty output.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Update ospfd and ospf6d to send opaque route attributes to
zebra. Those attributes are stored in the RIB and can be viewed
using the "show ip[v6] route" commands (other than that, they are
completely ignored by zebra).
Example:
```
debian# show ip route 192.168.1.0/24
Routing entry for 192.168.1.0/24
Known via "ospf", distance 110, metric 20, best
Last update 01:57:08 ago
* 10.0.1.2, via eth-rt2, weight 1
OSPF path type : External-2
OSPF tag : 0
debian#
debian# show ip route 192.168.1.0/24 json
{
"192.168.1.0\/24":[
{
"prefix":"192.168.1.0\/24",
"prefixLen":24,
"protocol":"ospf",
"vrfId":0,
"vrfName":"default",
"selected":true,
[snip]
"ospfPathType":"External-2",
"ospfTag":"0"
}
]
}
```
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Comparison of the two pointer is confusing, they have no relevance
except the time both of them are empty.
Additionly modify one variable name and correct some comment words, they
are same in both ospfd and ospf6d.
Signed-off-by: anlan_cs <anlan_cs@tom.com>
Currently, it is possible to rename the default VRF either by passing
`-o` option to zebra or by creating a file in `/var/run/netns` and
binding it to `/proc/self/ns/net`.
In both cases, only zebra knows about the rename and other daemons learn
about it only after they connect to zebra. This is a problem, because
daemons may read their config before they connect to zebra. To handle
this rename after the config is read, we have some special code in every
single daemon, which is not very bad but not desirable in my opinion.
But things are getting worse when we need to handle this in northbound
layer as we have to manually rewrite the config nodes. This approach is
already hacky, but still works as every daemon handles its own NB
structures. But it is completely incompatible with the central
management daemon architecture we are aiming for, as mgmtd doesn't even
have a connection with zebra to learn from it. And it shouldn't have it,
because operational state changes should never affect configuration.
To solve the problem and simplify the code, I propose to expand the `-o`
option to all daemons. By using the startup option, we let daemons know
about the rename before they read their configs so we don't need any
special code to deal with it. There's an easy way to pass the option to
all daemons by using `frr_global_options` variable.
Unfortunately, the second way of renaming by creating a file in
`/var/run/netns` is incompatible with the new mgmtd architecture.
Theoretically, we could force daemons to read their configs only after
they connect to zebra, but it means adding even more code to handle a
very specific use-case. And anyway this won't work for mgmtd as it
doesn't have a connection with zebra. So I had to remove this option.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Since f60a1188 we store a pointer to the VRF in the interface structure.
There's no need anymore to store a separate vrf_id field.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Issue #9983 explains what is wrong with the GR helper mode.
To unblock the CI that fails almost all the time on the ospf_gr_topo1
test, remove the commands and disable the test. Also add a reminder to
completely remove the helper mode if no one fixes the code in a month.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Description:
timerval datastructure is being used without initialization.
Using these uninitialized parameters can lead unexpected results
so initializing before using it.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Description:
In PointToPoint networks, There wont be DR and BDR.
But by default, All neighbours ism state is shown as
DR_OTHER.
Changed the nbr state format to <nbrsate>/- (ex : FULL/-)
to P2pnetworks.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Description:
1. Adding uptime to the 'show ip ospf neighbor' o/p.
2. Adding uptime and deadtime in string format for json consumption.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
It allows FRR to read the interface config even when the necessary VRFs
are not yet created and interfaces are in "wrong" VRFs. Currently, such
config is rejected.
For VRF-lite backend, we don't care at all about the VRF of the inactive
interface. When the interface is created in the OS and becomes active,
we always use its actual VRF instead of the configured one. So there's
no need to reject the config.
For netns backend, we may have multiple interfaces with the same name in
different VRFs. So we care about the VRF of inactive interfaces. And we
must allow to preconfigure the interface in a VRF even before it is
moved to the corresponding netns. From now on, we allow to create
multiple configs for the same interface name in different VRFs and
the necessary config is applied once the OS interface is moved to the
corresponding netns.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
The `show ip ospf neighbor json` command was displaying
state:`Full\/DR`
Where state was both the role and whether or not the neigbhor
was converged. While from a OSPF perspective this is the state.
This state is a combination of two things.
This creates a problem in testing because we have no guarantee
that a particular ospf router will actually have a particular role
given how loaded our topotest systems are. So add a bit of json
output to display both the converged status as well as the
role this router is playing on this neighbor/interface.
The above becomes:
state:`Full\/DR`
converged:`Full`
role:`DR`
Tests can now be modified to look for `Full` and allow it to
continue. Most of the tests do not actually care if this
router is the DR or Backup.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Considering that both the GR helper mode and restarting mode can be
enabled at the same time, the "graceful-restart helper-only" command
can be a bit misleading since it implies that only the helper mode
is enabled. Rename the command to "graceful-restart helper enable"
to clarify what the command does.
Start a deprecation cycle of one year before removing the original
command
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Several functions in ospf_vty.c were allocating json memory
irrelevant if it was needed or not and then at the end of the loop
free'ing it if it was not used. Clean up the access pattern.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The usage of json_object_to_json_string_ext is meant for
generation of output string and returns a `char *` pointer
to the `formatted` output. Just calling it does nothing
and it's expensive to boot.
Modify the code in ospfd to just output with the NOSLASHESCAPE
when outputting.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Problem Statement:
==================
Memory Leak seen at show_ip_ospf_neighbor_all_common (ospf_vty.c:4635)
RCA:
=================
In function show_ip_ospf_neighbor_all_common, one child json object is not
added to the parent child object when there is no nbma neighbor. Hence
the memory leak.
Fix:
=================
Add the child object to the parent json object.
Fixes: #9548
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
Problem Statement:
==================
When hello-interval is configured as 5, automatically dead interval becomes
4 times of hello i.e 20 seconds. But user wants the dead interval as
40 seconds and hello as 5 seconds. Therefore user configures it.
Now "ip ospf dead-interval 40" is not shown in "show running-config"
Therefore when user restarts the daemon, the dead interval goes back to
20 seconds and the neighbors are down.
Fix:
==================
If user configures dead-interval as 40, show it in show running config.
Fixes: #9401
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
There is a possibility that the same line can be matched as a command in
some node and its parent node. In this case, when reading the config,
this line is always executed as a command of the child node.
For example, with the following config:
```
router ospf
network 193.168.0.0/16 area 0
!
mpls ldp
discovery hello interval 111
!
```
Line `mpls ldp` is processed as command `mpls ldp-sync` inside the
`router ospf` node. This leads to a complete loss of `mpls ldp` node
configuration.
To eliminate this issue and all possible similar issues, let's print an
explicit "exit" at the end of every node config.
This commit also changes indentation for a couple of existing exit
commands so that all existing commands are on the same level as their
corresponding node-entering commands.
Fixes#9206.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
This command is currently always treated as an "unset" command, assuming
that active is the default type of the interface. In reality, the default
type of the interface can be changed using "passive-interface default"
command. Both "no" and regular commands can be "set" commands, depending
on the default value. They are treated as an "unset" when there's already
a config of the opposite type.
All this logic is in ospf_passive_interface_update.
Fixes#9240.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
The only difference in daemons' interface node definition is the config
write function. No need to define the node in every daemon, just pass
the callback as an argument to a library function and define the node
there.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Description:
Ospf process crashes upon giving 'clear ip ospf neighbor' with
self routerId. It is asserting if it is a self neighbor in ospf
neighbour kill event processing.
Added a check to validate the provided router-id is self
router-id.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Move `is_default_prefix` variations to `lib/prefix.h` and make the code
use the library version instead of implementing it again.
NOTE
----
The function was split into per family versions to cover all types.
Using `union prefixconstptr` is not possible due to static analyzer
warnings which cause CI to fail.
The specific cases that would cause this failure were:
- Caller used `struct prefix_ipv4` and called the generic function.
- `is_default_prefix` with signature using `const struct prefix *` or
`union prefixconstptr`.
The compiler would complain about reading bytes outside of the memory
bounds even though it did not take into account the `prefix->family`
part.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
RFC 3623 specifies the Graceful Restart enhancement to the OSPF
routing protocol. This PR implements support for the restarting mode,
whereas the helper mode was implemented by #6811.
This work is based on #6782, which implemented the pre-restart part
and settled the foundations for the post-restart part (behavioral
changes, GR exit conditions, and on-exit actions).
Here's a quick summary of how the GR restarting mode works:
* GR can be enabled on a per-instance basis using the `graceful-restart
[grace-period (1-1800)]` command;
* To perform a graceful shutdown, the `graceful-restart prepare ospf`
EXEC-level command needs to be issued before restarting the ospfd
daemon (there's no specific requirement on how the daemon should
be restarted);
* `graceful-restart prepare ospf` will initiate the graceful restart
for all GR-enabled instances by taking the following actions:
o Flooding Grace-LSAs over all interfaces
o Freezing the OSPF routes in the RIB
o Saving the end of the grace period in non-volatile memory (a JSON
file stored in `$frr_statedir`)
* Once ospfd is started again, it will follow the procedures
described in RFC 3623 until it detects it's time to exit the graceful
restart (either successfully or unsuccessfully).
Testing done:
* New topotest featuring a multi-area OSPF topology (including stub
and NSSA areas);
* Successful interop tests against IOS-XR routers acting as helpers.
Co-authored-by: GalaxyGorilla <sascha@netdef.org>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Problem Statement:
==================
[FRR OSPF] show ip ospf route json does not shown metric and tag.
Root Cause Analysis:
===================
In function show_ip_ospf_route_external, type 2 cost is not added in json.
Hence it is not displayed.
Fix:
=================
1. Add type2cost in the json display
2. Tag was also missing, added that as well
Issue: #8729
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
If we have the following configuration:
```
vrf red
smth
exit-vrf
!
interface red vrf red
smth
```
And we delete the VRF using "no vrf red" command, we end up with:
```
interface red
smth
```
Interface config is preserved but moved to the default VRF.
This is not an expected behavior. We should remove the interface config
when the VRF is deleted.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Add a null check to protect against the case where the neighbor
inactive timer is disabled. That can happen when the router is
acting as a helper for another router that is attempting to restart
gracefully.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Currently, passive interface flag is configured from the router node
using "passive-interface IFNAME". There are multiple problems with this
command:
- it is not in line with all other interface-related commands - other
parameters are configured from the interface node using "ip ospf"
prefix
- it is not in line with OSPFv3 - passive flag is configured from the
interface node using "ipv6 ospf6 passive" command
- most importantly, it doesn't work correctly when the interface is in
a different VRF - when using VRF-lite, it incorrectly changes the
vrf_id of the interface and it becomes desynced with the actual state;
when using netns, it creates a new fake interface and configures it
instead of configuring the necessary interface
To fix all the problems, this commit adds a new command to the interface
configuration node - "ip ospf passive". The purpose of the command is
completely the same, but it works correctly in a multi-VRF environment.
The old command is preserved for the backward compatibility, but the
warning is added that it is deprecated because it doesn't work correctly
with VRFs.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Found that in some circumstances, when the "ip ospf area"
command was entered for the default vrf, the wrong ospf
process would be used to check for the presence of a
"network" statement, causing the "ip ospf area" command to
be rejected. This was due to the command using the ospf
instance lookup to find the right ospf process, which can
be in error depending on when the processes were created.
Signed-off-by: Don Slice <dslice@nvidia.com>
When browsing or parsing OSPF LSA TLVs, we need to use the LSA length which is
part of the LSA header. This length, encoded in 16 bits, must be first
converted to host byte order with ntohs() function. However, Coverity Scan
considers that ntohs() function return TAINTED data. Thus, when the length is
used to control for() loop, Coverity Scan marks this part of the code as defect
with "Untrusted Loop Bound" due to the usage of Tainted variable. Similar
problems occur when browsing sub-TLV where length is extracted with ntohs().
To overcome this limitation, a size attribute has been added to the ospf_lsa
structure. The size is set when lsa->data buffer is allocated. In addition,
when an OSPF packet is received, the size of the payload is controlled before
contains is processed. For OSPF LSA, this allow a secure buffer allocation.
Thus, new size attribute contains the exact buffer allocation allowing a
strict control during TLV browsing.
This patch adds extra control to bound for() loop during TLV browsing to
avoid potential problem as suggested by Coverity Scan. Controls are based
on new size attribute of the ospf_lsa structure to avoid any ambiguity.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Currently ospfd relies on vrf bitmaps in zclient to check that the
redistribution is configured. This doesn't work when the VRF for OSPF
instance doesn't exist yet, because vrf bitmaps ignore VRF_UNKNOWN id.
Because of this, the following problems occur when the VRF doesn't exist:
- repeated "redistribute smth" command is processed as a first-time
instead of an update
- "no redistribute smth" doesn't work at all
This commit fixes both issues by relying on internal redistribution
config instead of zclient vrf bitmaps.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Description:
DR information is missing under "show ip ospf interface [json]".
Added DR infomation to display in "show ip ospf interface".
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
Currently, if NSSA area is configured before redistribution is enabled,
Type-7 LSA's are installed and flooded. But if NSSA area is configured
after redistribution is enabled, Type-7 LSA's are not installed.
With this change, when NSSA area is configured, schedule a task that
scans for external LSA's. If they exist, install Type-7 and flood to
all NSSA Areas.
There already was an attempt to fix this problem in 0f321812f where
ospf_asbr_nssa_redist_task() was triggered in ospf_abr_task_timer().
This turns out to be incorrect place for this operation because it's
a one-off operation needed only after "area <ID> nssa" execution. And
ospf_abr_task_timer() is a periodic operation. Triggering
ospf_asbr_nssa_redist_task() in ospf_abr_task_timer() caused a problem
that was fixed in 945eec2b6 making the problem with NSSA area
configured after redistribution actual again.
Signed-off-by: Alexander Chernavin <achernavin@netgate.com>
Allow over-write of message-digest-key interface config. Most
attributes handle multi-instance by ... ignoring instances,
and tolerating repeated config: do the same for md5 auth.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
When you set OSPF hello-interval for an interface and dead-interval is
not set for this interface, dead-interval will be calculated and set
automatically. "show running-config" will contain an invalid command:
test(config)# interface vpp1
test(config-if)# ip ospf area 0
test(config-if)# ip ospf hello-interval 1
test(config-if)# exit
test(config)#
test(config)# do show running-config
...
interface if1
ip ospf area 0
ip ospf dead-interval minimal hello-multiplier 0
ip ospf hello-interval 1
!
...
It causes frr-reload.py to fail because of this:
# vtysh -c "show running-config no-header" | vtysh -m -f -
line 9: % Unknown command: ip ospf dead-interval minimal hello-multiplier 0
...
With this change, output "ip ospf dead-interval" only if it has value
configured explicitly.
Signed-off-by: Alexander Chernavin <achernavin@netgate.com>
Instead of trying to maintain if_ospf_cli_count, let's directly count
the number of configured interfaces when it is needed. Current approach
sometimes leads to an incorrect counter.
Fixes#8321.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Description:
OSPF does not have an option to control the maximum multiple
equal cost paths to reach a destination/route(ECMP).
Currently, it is using the system specific max multiple paths.
But Somtimes, It requires to control the multiple paths from ospf.
This cli helps to configure the max number multiple paths in ospf.
Signed-off-by: Rajesh Girada <rgirada@vmware.com>
This command will trigger the OSPF forwarding address suppression in
translated type-5 LSAs, causing a NSSA ABR to use 0.0.0.0 as a forwarding
address instead of copying the address from the type-7 LSA
Example: In a topology like: R1 --- R2(ABR) --- R3(ASBR)
R3 is announcing a type-7 LSA that is translated to type-5 by the R2 ABR.
The forwarding address in the type-5 is by default copied from the type-7
r1# sh ip os da external
AS External Link States
LS age: 6
Options: 0x2 : *|-|-|-|-|-|E|-
LS Flags: 0x6
LS Type: AS-external-LSA
Link State ID: 3.3.3.3 (External Network Number)
Advertising Router: 10.0.25.2
LS Seq Number: 80000001
Checksum: 0xcf99
Length: 36
Network Mask: /32
Metric Type: 2 (Larger than any link state path)
TOS: 0
Metric: 20
Forward Address: 10.0.23.3 <--- address copied from type-7 lsa
External Route Tag: 0
r2# sh ip os database
NSSA-external Link States (Area 0.0.0.1 [NSSA])
Link ID ADV Router Age Seq# CkSum Route
3.3.3.3 10.0.23.3 8 0x80000001 0x431d E2 3.3.3.3/32 [0x0]
AS External Link States
Link ID ADV Router Age Seq# CkSum Route
3.3.3.3 10.0.25.2 0 0x80000001 0xcf99 E2 3.3.3.3/32 [0x0]
r2# conf t
r2(config)# router ospf
r2(config-router)# area 1 nssa suppress-fa
r2(config-router)# exit
r2(config)# exit
r2# sh ip os database
NSSA-external Link States (Area 0.0.0.1 [NSSA])
Link ID ADV Router Age Seq# CkSum Route
3.3.3.3 10.0.23.3 66 0x80000001 0x431d E2 3.3.3.3/32 [0x0]
AS External Link States
Link ID ADV Router Age Seq# CkSum Route
3.3.3.3 10.0.25.2 16 0x80000002 0x0983 E2 3.3.3.3/32 [0x0]
r1# sh ip os da external
OSPF Router with ID (11.11.11.11)
AS External Link States
LS age: 34
Options: 0x2 : *|-|-|-|-|-|E|-
LS Flags: 0x6
LS Type: AS-external-LSA
Link State ID: 3.3.3.3 (External Network Number)
Advertising Router: 10.0.25.2
LS Seq Number: 80000002
Checksum: 0x0983
Length: 36
Network Mask: /32
Metric Type: 2 (Larger than any link state path)
TOS: 0
Metric: 20
Forward Address: 0.0.0.0 <--- address set to 0
External Route Tag: 0
r2# conf t
r2(config)# router ospf
r2(config-router)# no area 1 nssa suppress-fa
r2(config-router)# exit
r1# sh ip os da external
OSPF Router with ID (11.11.11.11)
AS External Link States
LS age: 1
Options: 0x2 : *|-|-|-|-|-|E|-
LS Flags: 0x6
LS Type: AS-external-LSA
Link State ID: 3.3.3.3 (External Network Number)
Advertising Router: 10.0.25.2
LS Seq Number: 80000003
Checksum: 0xcb9b
Length: 36
Network Mask: /32
Metric Type: 2 (Larger than any link state path)
TOS: 0
Metric: 20
Forward Address: 0.0.0.0 <--- address set to 0
External Route Tag: 0
r2# conf t
r2(config)# router ospf
r2(config-router)# no area 1 nssa suppress-fa
r2(config-router)# exit
r1# sh ip os da external
OSPF Router with ID (11.11.11.11)
AS External Link States
LS age: 1
Options: 0x2 : *|-|-|-|-|-|E|-
LS Flags: 0x6
LS Type: AS-external-LSA
Link State ID: 3.3.3.3 (External Network Number)
Advertising Router: 10.0.25.2
LS Seq Number: 80000003
Checksum: 0xcb9b
Length: 36
Network Mask: /32
Metric Type: 2 (Larger than any link state path)
TOS: 0
Metric: 20
Forward Address: 10.0.23.3 <--- address copied from type-7 lsa
External Route Tag: 0
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
Current implementation of commands `show_ip_ospf_instance_database_cmd`
and `show_ip_ospf_instance_database_type_adv_router_cmd` have the
following problems:
- they doesn't have "vrf all" argument, however the processing of this
argument is implemented,
- they incorrectly implement json output for instances - they don't
output anything to the vty and don't release the json object.
To fix the problems, let's do the following:
1. Split `show_ip_ospf_instance_database_cmd` into two aliases to
`show_ip_ospf_database_max_cmd` and `show_ip_ospf_instance_database_max_cmd`.
The code is the same and doesn't need to be duplicated.
2. Split `show_ip_ospf_instance_database_type_adv_router_cmd` into two
separate functions - one regular and one for instances, which now
correctly implements the processing for json output.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Store instance index at startup and use it when processing vty commands.
The instance itself may be created and deleted by the user in runtime
using `[no] router ospf X` command.
Fixes#7908
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
The #if 0 code in ospfd, has not been compiled since at least
2012. If we are at least 9 years old at this point with no effort
to use or save, we should just get rid of it.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
