NEXTHOP_FLAG_ACTIVE currently means that the nexthop is considered
good enough to be installed. With current ecmp restrictions this
translation from multipath_num is enforced in the data plane.
The problem with this is of course that every data plane now
becomes concerned about the multipath num and must enforce it
independently. Currently *bsd does not honor multipath_num at
all and linux marks all nexthops as being installed even when
it honors a multipath_num that is less than the total.
This code change moves the multipath_num enforcement from a dataplane
decision to a zebra nexthop decision. Thus dataplanes now can
just install those nexthops marked as NEXTHOP_FLAG_ACTIVE
without having to worry about multipath_num.
*BSD will now respect multipath_num and Linux now properly notes
which routes are actually installed or not:
sharpd@donna ~/f/t/topotests> ps -ef | grep frr
frr 6261 1556 0 09:12 ? 00:00:00 /usr/lib/frr/zebra -e 2 --daemon -A 127.0.0.1
frr 6279 1556 0 09:12 ? 00:00:00 /usr/lib/frr/staticd --daemon -A 127.0.0.1
donna.cumulusnetworks.com(config)# do show ip route
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
F - PBR, f - OpenFabric,
> - selected route, * - FIB route
K>* 0.0.0.0/0 [0/106] via 10.0.2.2, enp0s3, 00:00:45
S>* 4.4.4.4/32 [1/0] via 10.0.2.1, enp0s3, 00:00:02
* via 192.168.209.1, enp0s8, 00:00:02
via 192.168.210.1, enp0s9 inactive, 00:00:02
C>* 10.0.2.0/24 is directly connected, enp0s3, 00:00:45
C>* 192.168.209.0/24 is directly connected, enp0s8, 00:00:45
C>* 192.168.210.0/24 is directly connected, enp0s9, 00:00:45
donna.cumulusnetworks.com(config)#
sharpd@donna ~/f/t/topotests> ip route show
default via 10.0.2.2 dev enp0s3 proto dhcp metric 106
4.4.4.4 proto 196 metric 20
nexthop via 10.0.2.1 dev enp0s3 weight 1
nexthop via 192.168.209.1 dev enp0s8 weight 1
10.0.2.0/24 dev enp0s3 proto kernel scope link src 10.0.2.15 metric 106
172.17.0.0/16 dev docker0 proto kernel scope link src 172.17.0.1 linkdown
192.168.122.0/24 dev virbr0 proto kernel scope link src 192.168.122.1 linkdown
192.168.209.0/24 dev enp0s8 proto kernel scope link src 192.168.209.2 metric 105
192.168.210.0/24 dev enp0s9 proto kernel scope link src 192.168.210.2 metric 103
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Problem reported that kernel neighbor entries could end up in "FAILED"
state when the neighbor entry was deleted. This fix handles the
notification of the event from netlink messages and re-inserts the
deleted entry.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Recursive multipath nexthops were broken by the initial async
dataplane - we were trying to install an extra, invalid
nexthop.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Reduce or eliminate use of global zebra_ns structs in
a couple of netlink/kernel code paths, so that those paths
can potentially be made asynch eventually.
Slide netlink_talk_info into place to remove dependency on core
zebra structs; add accessors for dplane context block
Start init of route context from zebra core re and rn structs;
start queueing and event handling for incoming route updates.
Expose netlink apis that don't rely on zebra core structs;
add parallel route-update code path using the dplane ctx;
simplest possible event loop to process queued route'
updates.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Conditional code in netlink_macfdb_update() introduced in 2232a77c used
the 'dst_present' variable because not all cases were covered. Now it is
not necessary.
Signed-off-by: F. Aragon <paco@voltanet.io>
Reduce or eliminate use of global zebra_ns structs in
a couple of netlink/kernel code paths, so that those paths
can potentially be made asynch eventually.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Use boolean variables instead of unsigned int for certain VxLAN-EVPN
flags which are really used as boolean.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Chirag Shah <chirag@cumulusnetworks.com>
Ticket: CM-22288
Reviewed By: CCR-7832
Testing Done:
Along with a subsequent, related commit
When a MAC moves from local to remote, a replace is allowed, EVPN
no longer has to delete the local MAC before installing the remote
MAC.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Reviewed-by: Chirag Shah <chirag@cumulusnetworks.com>
So the linux kernel uses the RT_TABLE_MAIN for the table
id used for ip routing. The multicast routing tables use
RT_TABLE_DEFAULT. We changed the internal code of zebra_vrf
a few months back to use RT_TABLE_MAIN as the tableid to
use. This caused the pim sg stats to stop working because
of the kernel bug where it uses a different table
for ip routing and ip multicast.
Put a bit of a special case in to do the right thing.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Newer linux kernels apparently send data down the netlink
bus for the creation of mroutes. Add a bit of code
to notice this and to handle it appropriately( ie do
nothing at this point in time ) as that the correct
place to do this is in the pim socket in pimd.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When we are displaying data about a netlink message
in debugs or errors, print out the message type
as a string instead of a number.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
There exists a possibility that the ifindex we are passed
does not exist and as such we should check for it not
resolving as part of the debug.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
We were ignoring mpls labels encapped with static routes.
Added support for single and multipath labels.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow protocols to specify to zebra that they would like zebra
to use the distance passed down as part of determine sameness for
Route Replace semantics.
This will be used by the static daemon to allow it to have
backup static routes with greater distances.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Prefix length validation checks should be returning an error
rather than 0. Switch to that and make them error messages.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Commit a2ca67d1d2 consolidated IPv4 and IPv6 handling. It also applied
our ignorance for IPv4 srcdest routes onto IPv6.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Bad nexthop messages from netlink were causing zebra
to hang here. Added a check to verify the length
of the nexthop so it doesn't keep trying to read.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Some more address family filters we can safely ignore
as well as typos in logger. Added AF_MPLS as filterable.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Zebra needed a check that varifies the prefix length
of an address is a valid length when receiving route
changes and interface address changes.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
The zebra netlink socket was attempting to read netlink
messages with invalid address families in a couple areas.
Added filters and warn messages.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
EVPN ND ext community support NA flag R-bit, to have proxy ND.
Set R-bit in EVPN NA if a given router is default gateway or there is a
local
router attached, which can be determine based on local neighbor entry.
Implement BGP ext community attribute to generate and parse R-bit and
pass along zebra to program neigh entry in kernel.
Upon receiving MAC/IP update with community type 0x06 and sub_type 0x08,
pass the R-bit to zebra to program neigh entry.
Set NTF_ROUTER in neigh entry and inform kernel to do proxy NA for EVPN.
Ref:
https://tools.ietf.org/html/draft-ietf-bess-evpn-na-flags-01
Ticket:CM-21712, CM-21711
Reviewed By:
Testing Done:
Configure Local vni enabled L3 Gateway, which would act as router,
checked
show evpn arp-cache vni x ip <ip of svi> on originated and remote VTEPs.
"Router" flag is set.
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Add 'const' to prefix args to several zebra route update,
redistribution, and route owner notification apis.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
The interface lookup algorithm is different according to if we are on
netns vrf or not. If we are on the former case, then we only have to
parse the interfaces of the netns, while if we are on the other case, we
have to parse all the interfaces of all the vrfs ( since index is not
overlapping in the latter case).
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When we receive a netlink message from the kernel we have
handler functions for when we send a netlink command, if these
return a failure ( < 0 ) then we output that we had a parse
issue. But if all we get is:
2018-06-21T23:47:45.298156+00:00 qct-ix1-08 zebra[1484]: netlink-cmd (NS 0) filter function error
Then it is not very useful to figure out *where* the error happened.
Add more error code when in a decode path to hopefully allow us
to figure out where this message is coming from.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add a bit of code to allow return of data plane
request messages.
Add the ability to pass the result back to callers
of kernel_route_rib.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
