RFC 8966 requires a bit of work to make FRR forward compabitble with
it for the moment.
tl;dr -> Flags of hellos should be 0 except the main bit and
The Unicast Hello bit if set should cause the packet to be ignored.
Additionally FRR needs to ignore Hello packets with the interval field
set to 0.
Fixes: #11349
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Moving the common lines of pim_show_nexthop cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_neighbors_vrf_all cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_neighbors cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_local_membership cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_jp_agg cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_interface_vrf_all cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_interface cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Moving the common lines of pim_show_channel cli
in pim_cmd.c and pim6_cmd.c to pim_cmd_common.c file
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
The test for setting pimDesignatedRouterLocal was comparing
the result of pim_addr_cmp to non zero to say that the
pim_dr_addr and primary_address are the same. This is
not correct in that pim_addr_cmp returns 0 for being the
same, so the correct test is !pim_addr_cmp
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
PIM conformance test case 11.12 sends a register stop msg with
source address as 0. This should trigger a register stop for
all the upstreams. It is not happening as such because we are not
considering 0.0.0.0 source address for starg_handling.
Fixed it.
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
Prior to this fix, restarting the client just failed b/c the code tried to
"refresh" the existing LSA being added, except that code checked for meta-data
to exist, which was deleted when the client disconnected previously (or had
never connected and the LSA state was picked up from the network).
Signed-off-by: Christian Hopps <chopps@labn.net>
Reachable router information is used by OSPF opaque clients in order
to determine if the router advertising the opaque LSA data is
reachable (i.e., 2-way conectivity check).
Signed-off-by: Christian Hopps <chopps@labn.net>
The reachable router table is used by OSPF opaque clients in order to
determine if the router advertising the opaque LSA data is
reachable (i.e., 2-way conectivity check).
Signed-off-by: Christian Hopps <chopps@labn.net>
Only the multi-topology command can use 'ipv4-unicast' keyword to
configure standard topology.
The remaining code: dump from show commands, and yang definition,
uses 'standard' keyword instead.
The test have not been modified. The change would consists in
modifying test_fuzz_isis_tlv_tests.h.gz:
- replacing ipv4-unicast occurences with standard
\x69\x70\x76\x34\x2d\x75\x6e\x69\x63\x61\x73\x74
with
\x73\x74\x61\x6e\x64\x61\x72\x64
- align the buffer length by removing 4 bytes per occurence
Instead, a specific isis_mtid2str_fake() routing has been
put in place in isis_tlvs.c file.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
