Allow protocols to specify to zebra that they would like zebra
to use the distance passed down as part of determine sameness for
Route Replace semantics.
This will be used by the static daemon to allow it to have
backup static routes with greater distances.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This is the start of separating out the static
handling code from zebra -> staticd. This will
help simplify the zebra code and isolate static
route handling to it's own code base.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
As part of moving the static route handling to it's own daemon
allow zebra to accept static route types from upper level
protocols.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
show evpn mac vni all
show evpn mac vni x
does not display local svi and anycast mac into count.
Ticket:CM-20456
Testing Done:
Before:
TOR1# show evpn mac vni 1008
Number of MACs (local and remote) known for this VNI: 4
MAC Type Intf/Remote VTEP VLAN
44:38:39:00:6b:4c local vlan1008 1008
00:02:00:00:00:04 local hostbond5 1008
00:02:00:00:00:02 local hostbond4 1008
00:00:5e:00:01:01 local vlan1008-v0 1008
00:02:00:00:00:0c remote 27.0.0.15
00:02:00:00:00:0a remote 27.0.0.15
dell-s6000-07#
After:
TOR1# show evpn mac vni 1008
Number of MACs (local and remote) known for this VNI: 6
MAC Type Intf/Remote VTEP VLAN
44:38:39:00:6b:4c local vlan1008 1008
00:02:00:00:00:04 local hostbond5 1008
00:02:00:00:00:02 local hostbond4 1008
00:00:5e:00:01:01 local vlan1008-v0 1008
00:02:00:00:00:0c remote 27.0.0.15
00:02:00:00:00:0a remote 27.0.0.15
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
When I did a show ip route with `json` on a vrf when it didn't exist,
frr would output invalid json.
Signed-off-by: Nathan Van Gheem <nathan@cumulusnetworks.com>
The parameter was missing in that vty command. Then it is being added.
Also some documentation is refreshed.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
NLMSG_NEXT decrements the buffer length (status) by
the header msg length (nlmsg_len) everytime its called.
If nlmsg_len isn't accurate and set to be larger than
what it should represent, it will cause status to
decrement passed 0. This makes NLMSG_NEXT return a
pointer that references an inaccessible address.
When that is passed to NLMSG_OK, it segfaults.
Add a check to verify that there is still something to read
before we try to.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Prefix length validation checks should be returning an error
rather than 0. Switch to that and make them error messages.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Change the fuzzing code so that it fakes data from
the listening socket rather than using its own pseudo one.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Commit a2ca67d1d2 consolidated IPv4 and IPv6 handling. It also applied
our ignorance for IPv4 srcdest routes onto IPv6.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Each ipset with port value monitors either src port or dst port.
The information is added to show pbr iptable commmand.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Bad nexthop messages from netlink were causing zebra
to hang here. Added a check to verify the length
of the nexthop so it doesn't keep trying to read.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Some more address family filters we can safely ignore
as well as typos in logger. Added AF_MPLS as filterable.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Zebra needed a check that varifies the prefix length
of an address is a valid length when receiving route
changes and interface address changes.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Zebra needed a check for mtu from the message it
received from the kernel before adding the new link.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
The zebra netlink socket was attempting to read netlink
messages with invalid address families in a couple areas.
Added filters and warn messages.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
This code allows you to fuzz the netlink listening socket
in zebra by --enable-fuzzing and passing the -w [FILE]
option when running zebra.
File collection is stored in /var/run/frr/netlink_*
where each number is just a counter to keep the
files distinct.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
To keep configuration consistent, vrf that have not been able to be
associated with netns are removed.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
