Clean up a few lines of cli command installation; remove a
duplicate; follow the command grouping pattern better.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
There can be cases where evpn traffic is not meshed across various
endpoints, but sent to a central pe. For this situation, remove the
nexthop unchanged default behaviour for bgp evpn. Also add route
reflector commands to bgp evpn node.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The `bgp bestpath bandwidth` command should not be a legal
command. Pull out the `no` form to allow this. Allow
`no bgp bestpath bandwidth` to work as we would expect.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The problem is that peer_af_array returns NULL when SAFI is changed to
unicast. We use unicast table, but peer is created and activated under
labeled-unicast, hence we should lookup with a proper SAFI id.
Without this patch peer_af_find() returns NULL and we can't show
PfxSnt in `show bgp summary`.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Modify the import-check command to require the underlying prefix
to exist in the rib. General consensus is that this is the correct
behavior.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Problem reported that in many circumstances, RAs created in the
process of bringing up numbered IPv6 peers with extended-nexthop
capability enabled (for ipv4 over ipv6) were not stopped on the
interface when those peers were deleted. Found several circumstances
where this occurred and fix them in this patch.
Ticket: CM-26875
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
- Fix 1 byte overflow when showing GR info in bgpd
- Use PATH_MAX for path buffers
- Use unsigned specifiers for uint16_t's in zebra pbr
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Replace sprintf with snprintf where straightforward to do so.
- sprintf's into local scope buffers of known size are replaced with the
equivalent snprintf call
- snprintf's into local scope buffers of known size that use the buffer
size expression now use sizeof(buffer)
- sprintf(buf + strlen(buf), ...) replaced with snprintf() into temp
buffer followed by strlcat
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
And again for the name. Why on earth would we centralize this, just so
people can forget to update it?
Signed-off-by: David Lamparter <equinox@diac24.net>
Same as before, instead of shoving this into a big central list we can
just put the parent node in cmd_node.
Signed-off-by: David Lamparter <equinox@diac24.net>
There is really no reason to not put this in the cmd_node.
And while we're add it, rename from pointless ".func" to ".config_write".
[v2: fix forgotten ldpd config_write]
Signed-off-by: David Lamparter <equinox@diac24.net>
The only nodes that have this as 0 don't have a "->func" anyway, so the
entire thing is really just pointless.
Signed-off-by: David Lamparter <equinox@diac24.net>
Some competitive vendors like Cisco, Bird, OpenBGPD,
Nokia already have this by default enabled.
The list is here: https://github.com/bgp/RFC8212
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
... Oops ...
(for context, the defaults code originally didn't have a dedicated
"bool" variant and just used long for bools... I derp'd this when
adding bool as a separate case :( )
Reported-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@diac24.net>
This macro is undefined if vnc is disabled, and while it defaults to 0,
this is still wrong and causes issues with -Werror
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Support configurable options to control how link bandwidth is handled
by the receiver. The default behavior is to automatically honor the
link bandwidths received and use it to perform a weighted ECMP BUT only
if all paths in the multipath have associated link bandwidth; if one or
more paths do not have link bandwidth, normal ECMP is performed among
the multipaths. This behavior is as recommended by
https://tools.ietf.org/html/draft-ietf-idr-link-bandwidth.
The additional options available are to (a) completely ignore any link
bandwidth (i.e., weighted ECMP is effectively disabled), (b) skip paths
in the multipath which do not have link bandwidth and perform weighted
ECMP among the other paths (if at least some paths have the bandwidth)
or (c) use a default weight (value chosen is 1) for the paths which
do not have link bandwidth.
The command syntax is
bgp bestpath bandwidth <ignore|skip-missing|default-weight-for-missing>
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
In the past, we always displayed the number of buffered ingress packets
as zero because there was no packet buffering in the input path and
therefore never any queue size to report. They're buffered now so we can
display something meaningful instead of 0.
Also change the inq / outq lookups to be atomic, since they can be
modified elsewhere. These should still compile down to an unfenced word
read but it's good to be explicit.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Add new function `bgp_node_get_prefix()` and modify
the bgp code base to use it.
This is prep work for the struct bgp_dest rework.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Problem seen that if "import vrf route-map RMAP" was entered
without any vrfs being imported, the configuration was displayed
as "route-map vpn import RMAP". Additionally, if "import vrf
route-map" was entered without specifying a route-map name,
the command was accepted and the word "route-map" would be
treated as a vrf name. This fix resolves both of those issues
and also allows deleting the "import vrf route-map" line without
providing the route-map name.
Ticket: CM-28821
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Some were converted to bool, where true/false status is needed.
Converted to void only those, where the return status was only false or true.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
RCA: When doppelganger still around and clear bgp is issued
there are chances of peer getting deleted and next pointer
is a freed peer pointer.
Fix: Pass address of nnode to get next safe peer pointer.
Signed-off-by: Santosh P K <sapk@vmware.com>
annie# show bgp ipv4 uni summ
BGP router identifier 192.168.201.136, local AS number 64539 vrf-id 0
BGP table version 22458946
RIB entries 1458006, using 178 MiB of memory
Peers 4, using 68 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
45.33.5.119 4 0 0 0 0 0 0 never Active
65.19.134.122 4 15096 4611832 108292 0 0 0 6d22h55m 800670
107.13.46.23 4 0 0 0 0 0 0 never Connect
robot(192.168.201.139) 4 64540 11159975 11365599 0 0 0 05w2d05h Connect
Total number of neighbors 4
On very busy systems The column output for MsgRcvd and MsgSent can quickly move past 7 columns.
Add a couple more to allow for even display.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
