```
donatas-pc(config-router)# timers bgp 8 12
% keeplive value 8 is larger than 1/3 of the holdtime, setting to 4
donatas-pc(config-router)# do sh run | include timers bgp
timers bgp 4 12
donatas-pc(config-router)#
```
Closes https://github.com/FRRouting/frr/issues/14287
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
When the BGP 'redistribute table' command is used for a given route
table, and BGP configuration is flushed and rebuilt, the redistribution
does not work.
Actually, when flushing the BGP configuration with the 'no router bgp'
command, the BGP redistribute entries related to the 'redistribute table'
entries are not flushed. Actually, at BGP deletion, the table number is
not given as parameter in bgp_redistribute_unset() function, and the
redistribution entry is not removed in zebra.
Fix this by adding some code to flush all the redistribute table
instances.
Fixes: 7c8ff89e93 ("Multi-Instance OSPF Summary")
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
As part of the conversion to a `struct peer_connection` it will
be desirable to have 2 pointers one for when we open a connection
and one for when we receive a connection. Start this actual
conversion over to this in `struct peer`. If this sounds confusing
take a look at the bgp state machine for connections and how
it resolves the processing of this router opening -vs- this
router receiving an open. At some point in time the state
machine decides that we are keeping one of the two connections.
Future commits will allow us to untangle the peer/doppelganger
duality with this abstraction.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The status and ostatus are a function of the `struct peer_connection`
move it into that data structure.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Move PEER_THREAD_WRITES_ON and PEER_THREAD_READS_ON to
be a part of the `struct peer_connection` since this is
a connection oriented bit of data.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Move the peer->t_write and peer->t_read into `struct peer_connection`
as that these are properties of the connection.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
P# Please enter the commit message for your changes. Lines starting
BGP tracks connections based upon the peer. But the problem
with this is that the doppelganger structure for it is being
created. This has introduced a bunch of fragileness in that
the peer exists independently of the connections to it.
The whole point of the doppelganger structure was to allow
BGP to both accept and initiate tcp connections and then
when we get one to a `good` state we collapse into the
appropriate one. The problem with this is that having
2 peer structures for this creates a situation where
we have to make sure we are configing the `right` one
and also make sure that we collapse the two independent
peer structures into 1 acting peer. This makes no sense
let's abstract out the peer into having 2 connection
one for incoming connections and one for outgoing connections
then we can easily collapse down without having to do crazy
stuff. In addition people adding new features don't need
to have to go touch a million places in the code.
This is the start of this abstraction. In this commit
we'll just pull out the fd and input/output buffers
into a connection data structure. Future commits
will abstract further.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Before the patch:
```
donatas-laptop(config-router)# bgp confederation
identifier AS number in plain <1-4294967295> or dotted <0-65535>.<0-65535> format
peers Peer ASs in BGP confederation
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Even if some of the attributes in bgp_path_info_extra are
not used, their memory is still allocated every time. It
cause a waste of memory.
This commit code deletes all unnecessary attributes and
changes the optional attributes to pointer storage. Memory
will only be allocated when they are actually used. After
optimization, extra info related memory is reduced by about
half(~400B -> ~200B).
Signed-off-by: Valerian_He <1826906282@qq.com>
Add this logic inside bgp_capability_send() instead of repeating the whole
logic before calling bgp_capability_send().
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
When setting local-role for the neighbor, force sending ROLE capability via
dynamic capability if it's enabled.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
We have dynamic capability support, but it handles only MP capability.
With this change, we can enable software version capability dynamicaly, without
resetting the session.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Include an event ptr-to-ptr in the event_execute() api
call, like the various schedule api calls. This allows the
execute() api to cancel an existing scheduled task if that
task is being executed inline.
Signed-off-by: Mark Stapp <mjs@labn.net>
The last_reset_cause is a plain old BGP_MAX_PACKET_SIZE buffer
that is really enlarging the peer data structure. Let's just
copy the stream that failed and only allocate how ever much
the packet size actually was. While it's likely that we have
a reset reason, the packet typically is not going to be 65k
in size. Let's save space.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
problem:
In CLI config codeflow there are memory leaks in failure scenario
Fix:
Code changes are done to free ecommunity
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
Useful to have it for datacenter profile only, disabled for traditional.
If the peer is not established or established, but has no description set,
we will show the FRR version instead, which is kinda handy to have instead of
nothing.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
More details: https://www.rfc-editor.org/rfc/rfc8810.html
Not sure if we want to maintain the old code more.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
Also, this is visible only if `capability software-version` is enabled.
Example:
```
r1# show ip bgp summary
IPv4 Unicast Summary (VRF default):
BGP router identifier 192.168.1.1, local AS number 65001 vrf-id 0
BGP table version 0
RIB entries 0, using 0 bytes of memory
Peers 1, using 725 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
192.168.1.2 4 65002 54 54 0 0 0 00:00:52 0 0 FRRouting/9.1-dev-My
Total number of neighbors 1
r1#
```
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
After some VRF imports are removed and "no bgp retain route-target all"
is set, prefixes that are not imported anymore remain in the BGP table.
Parse the BGP table and remove un-imported prefixes in such a case.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
When acting as intermediate device for BGP signaling, and
as transit device for data traffic, the device is not able
to modify the label value from incoming MPLS VPN updates:
- as BGP device, modifying the label value is necessary
when redistributing VPN prefixes with its own next-hop.
- as transit device that connects two ethernet segments
on separate interfaces, the return MPLS traffic must be
handled: the modified label value must be swapped with
the original label value and sent back to the original
next-hop.
The border router use case can be taken as example, when
it acts both as transit and as BGP device:
- When receiving updates from a border router peer, and where
interior traffic is expected to transit through the local
border router.
- When receiving updates from interior devices, and where
exterior traffic will transit through the local border router.
In those two situations, a new label is bound to the received
entry, and the entry is advertised to a new peer with the new
label. In the same time, an MPLS entry is created to handle
return traffic with the new mpls label: the traffic would be
swapped to the original MPLS label and the original next-hop.
This is the first commit of a series of patches, that address
the above mentioned issue.
The first commit introduces a new per-interface command:
> interface eth0
> [no] mpls bgp l3vpn-multi-domain-switching
> exit
This command will authorise mpls vpn updates to have a new
label value bound to the mpls vpn routes received over that
interface.
Link: https://www.rfc-editor.org/rfc/rfc3107.html#section-3
> When a BGP speaker redistributes a route, the label(s) assigned to
> that route must not be changed (except by omission), unless the
> speaker changes the value of the Next Hop attribute of the route.
Link: https://www.rfc-editor.org/rfc/rfc3031.html#section-4.6
Link: https://www.rfc-editor.org/rfc/rfc4364.html#section-10
sub-chapter b.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When using `addpath-tx-all` BGP announces all known paths instead of announcing
only an arbitrary number of best paths.
With this new command we can send N best paths to the neighbor. That means, we
send the best path, then send the second best path excluding the previous one,
and so on. In other words, we run best path selection algorithm N times before
we finish.
Signed-off-by: Donatas Abraitis <donatas@opensourcerouting.org>
The only places entry->any could ever be set to true was
when str was NULL. Unfortunately with the way our CLI works
str is impossible to be NonNULL. The entry->any value *used*
to work prior to commit e961923c72
but it was changed back in 2016 and no-one has noticed the changed
ability.
Let's just admit that there are no users of this and remove this
dead code.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Let's account for vpn_policy_getafi having a failure
situation and back out of the whole thing gracefully.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
A new VTY command is introduced in ipv4 unicast and ipv6 unicast
address family, under a BGP instance.
> r1# label vpn export allocation-mode per-nexthop|per-vrf
This command will update the label values associated for each
BGP update to export to the global instance. Two modes are
available: per-nexthop and per-vrf. The latter is the default
one.
With this commit only, configuring label allocation per nexthop
will only reset the BGP updates, and the per-vrf mode label
allocation will be chosen.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Until now, the bgp local paths were using the default null label
defined. It was not possible to select the null label for the ipv4
or the ipv6 address families.
This commit addresses this issues by adding two extra-parameters
to the BGP labeled-unicast command.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
In BGP labeled unicast address-family, it is not possible to
send explicit-null label values with redistributed or network
declared prefixes.
A new CLI command is introduced:
> [no] bgp labeled-unicast explicit-null
When used, the explicit-null value for IPv4 ('0' value) or
IPv6 ('2' value) will be used.
It is necessary to reconfigure the networks or the
redistribution in order to inherit this new behaviour.
Add the documentation.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When we have these sequence of events causing a crash in
evpn_type5_test_topo1:
(A) no router bgp vrf RED 100
this schedules for deletion the vrf RED instance
(B) a l3vni change event from zebra
this creates a bgp instance for VRF RED in some cases
additionally it auto imports evpn routes into VRF RED
Please note this is desired behavior to allow for the
auto importation of evpn vrf routes
(C) no router bgp 100
The code was allowing the deletion of the default
instance and causing tests to crash.
Effectively the test in bgp_vty to allow/dissallow
the removal of the default instance was not correct
for the case when (B) happens.
Let's just not allow the command to succeed in this case as that
the test was wrong.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Fix for missing neighbor description in "show bgp summary [wide]"
when its length exceeds 20[64] chars and it doesn't contain
withespaces.
Existing behavior remains if description contains whitespaces
before size limit.
Signed-off-by: rbarroetavena <rbarroetavena@gmail.com>
