The bgp_notify_conditional_adv_scanner function was/is looping
over all peers. And only matching on the passed in peer,
based upon the subgroup. As such we do not need to loop
over everything and just cut-to-the chase and just modify
the peer structure.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Unsuppress route part of the aggregation when route-map configuration
is removed before the aggregation itself.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Description:
Change is intended for fixing the issue related to
clearing of stale leaked routes:
- Whenever BGP goes down,
after bringing down tcp connection and renegotiating capabilities,
once we reestablish connection,
we are not handling clear of VRF leaked route in the bgp_clear_stale_route.
- While bgp is clearing stale routes,
we need to handle withdraw of routes for VRF route-leaking.
Co-authored-by: Kantesh Mundaragi <kmundaragi@vmware.com>
Signed-off-by: Iqra Siddiqui <imujeebsiddi@vmware.com>
rfc7196 recommends:
In addition, BGP implementations have an internal constant, which we
will call the 'maximum penalty', and the current computed penalty may
not exceed it.
Router Maximum Penalty: The internal constant for the maximum
penalty value MUST be raised to at least 50,000.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Currently the Wait for Install code ( bgp_suppress_fib ) does
not properly handle two states from zebra: ROUTE_INSTALL_FAILED
and BETTER_ADMIN_DISTANCE_WON. Pre this change the WFI code
would just never notify our peers about a route install failure
but more is needed. In the ROUTE_INSTALL_FAILED and the
BETTER_ADMIN_DISTANCE_WON we need to notify our peers with
a withdrawal about the route, else we will continue to
draw traffic to us when we cannot legally do so.
Why is this needed? In either case imagine that we've already
received a bgp route, installed it and sent to our peers.
In the Better admin distance won case, say a static route is installed
at this point in time we must stop advertising the route through
us since we are not installed. As such a withdrawal must be sent.
In the ROUTE_INSTALL_FAILED case, the code was not properly handling
the situation where we have Route A, it was successfully installed
and then we received a update to Route A that was attempted to be
installed but failed. In this case we also need to send a withdrawal
Finally update the bgp_suppress_fib topotest to test both of these
situations.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Don't hide the LABELED_UNICAST safi when processing route
updates; map it where necessary (to use the UNICAST table
for instance).
Signed-off-by: Mark Stapp <mstapp@nvidia.com>
Move the "longer-prefixes" option from show_ip_bgp_cmd to
show_ip_bgp_json_cmd so that is has access to JSON output.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Move the "route-map" option from show_ip_bgp_cmd to
show_ip_bgp_json_cmd so that is has access to JSON output.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Move the "filter-list" option from show_ip_bgp_cmd to
show_ip_bgp_json_cmd so that is has access to JSON output.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Move the "prefix-list" option from show_ip_bgp_cmd to
show_ip_bgp_json_cmd so that is has access to JSON output.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Move the "community-list" option from show_ip_bgp_cmd to
show_ip_bgp_json_cmd so that is has access to JSON output.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
There's no need to have different calls to bgp_show() when the only
difference is one argument that corresponds to a "void *" parameter.
Code duplication should be reduced to a minimum to avoid bugs like
the one fixed in the previous commit.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Like done in the other places (when "all" isn't used), pass the
actual alias name to bgp_show() instead of a null pointer.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Description:
Incorrect behavior during best path selection for the imported routes.
Imported routes are always treated as eBGP routes.
Change is intended for fixing the issues related to
bgp best path selection for leaked routes:
- FRR does ecmp for the imported routes,
even without any ecmp related config.
If the same prefix is imported from two different VRFs,
then we configure the route with ecmp even without
any ecmp related config.
- Locally imported routes are preferred over imported
eBGP routes.
If there is a local route and eBGP learned route
for the same prefix, if we import both the routes,
imported local route is selected as best path.
- Same route is imported from multiple tenant VRFs,
both imported routes point to the same VRF in nexthop.
- When the same route with same nexthop in two different VRFs
is imported from those two VRFs, route is not installed as ecmp,
even though we had ecmp config.
- During best path selection, while comparing the paths for imported routes,
we should correctly refer to the original route i.e. the ultimate path.
- When the same route is imported from multiple VRF,
use the correct VRF while installing in the FIB.
- When same route is imported from two different tenant VRFs,
while comparing bgp path info as part of bgp best path selection,
we should ideally also compare corresponding VRFs.
See-also: https://github.com/FRRouting/frr/files/7169555/FRR.and.Cisco.VRF-Lite.Behaviour.pdf
Co-authored-by: Santosh P K <sapk@vmware.com>
Co-authored-by: Kantesh Mundaragi <kmundaragi@vmware.com>
Signed-off-by: Iqra Siddiqui <imujeebsiddi@vmware.com>
We should send only 16bytes next hop, no need for 32bytes, third party
next hops kinda for LLA does not work here.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
When debugging issues for routes in multiple vrf's. It would
be extremely useful if the debug output had which vrf we
are acting on.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
AFI/SAFI is handled in bgp_vty_find_and_parse_afi_safi_bgp() properly for
IPv4, but not for IPv6. Let's have it enabled for IPv6 by default.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
AFI/SAFI is handled in bgp_vty_find_and_parse_afi_safi_bgp() properly for
IPv4, but not for IPv6. Let's have it enabled for IPv6 by default.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
```
exit1-debian-9# show ip route 172.16.16.1/32
Routing entry for 172.16.16.1/32
Known via "bgp", distance 20, metric 0, best
Last update 00:00:28 ago
* 192.168.0.2, via eth1, weight 1
AS-Path : 65003
Communities : first 65001:2 65001:3
Large-Communities: 65001:1:1 65001:1:2 65001:1:3
Selection reason : First path received
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
`bgp` pointer always exists and is used before this function call.
Calling `free` in `json` in this context will also cause a
use-after-free crash.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
In some cases where bgp is at the mpls edge, where it has a BGP-LU
peer downstream but an IP peer upstream, it can advertise the
IMPLICIT_NULL label instead of a per-prefix label.
Signed-off-by: Mark Stapp <mstapp@nvidia.com>
The '... json detail' output is missing some data that's shown
via the 'route_vty_out_detail_header' function. Integrate the
json version of that function in the 'json detail' path.
Signed-off-by: Mark Stapp <mstapp@nvidia.com>
following command: show bgp l2vpn evpn rd all tags
does not append rd contexts one after the other
before:
dut-vm# show bgp l2vpn evpn rd all tags
Network Next Hop In tag/Out tag
Route Distinguisher: 65000:999
*> [5]:[0]:[24]:[10.40.1.0]
10.209.36.1 Route Distinguisher: 65000:1000
*> [5]:[0]:[24]:[10.40.1.0]
10.209.36.1
Displayed 2 out of 2 total prefixes
after:
dut-vm# show bgp l2vpn evpn rd all tags
Network Next Hop In tag/Out tag
Route Distinguisher: 65000:999
*> [5]:[0]:[24]:[10.40.1.0]
10.209.36.1
Route Distinguisher: 65000:1000
*> [5]:[0]:[24]:[10.40.1.0]
10.209.36.1
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
There are places where we use route-maps using duplicated attributes and
neither intern nor flush them after the usage. If a route-map has set
rules for aspath/communities, they will be allocated and never freed.
We should always flush unneeded duplicated attributes.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
EVPN paths are maintained in per-ES list for efficient updates
(es→macip_global_path_list, es→macip_evi_path_list). VNI is also maintained
in path_extra for easy lookups. This (path_extra) VNI (which is always 0 for
global paths) was being displayed against the path and was mis-interpreted
as the BD.
To avoid that confusion I have removed the display.
Ticket: #2732605
Signed-off-by: Anuradha Karuppiah <anuradhak@nvidia.com>
Description:
Change is intended for fixing the following issues related to vrf route leaking:
Routes with special nexthops i.e. blackhole/sink routes when imported,
are not programmed into the FIB and corresponding nexthop is set as 'inactive',
nexthop interface as 'unknown'.
While importing/leaking routes between VRFs, in case of special nexthop(ipv4/ipv6)
once bgp announces route(s) to zebra, nexthop type is incorrectly set as
NEXTHOP_TYPE_IPV6_IFINDEX/NEXTHOP_TYPE_IFINDEX
i.e. directly connected even though we are not able to resolve through an interface.
This leads to nexthop_active_check marking nexthop !NEXTHOP_FLAG_ACTIVE.
Unable to find the active nexthop(s), route is not programmed into the FIB.
Whenever BGP leaks routes, set the correct nexthop type, so that route gets resolved
and correctly programmed into the FIB, in the imported vrf.
Co-authored-by: Kantesh Mundaragi <kmundaragi@vmware.com>
Signed-off-by: Iqra Siddiqui <imujeebsiddi@vmware.com>
if advertisement with SID structure Sub-Sub-TLV, we need to transpose
SID, so added transpose operation into bgp_update.
Signed-off-by: Ryoga Saito <contact@proelbtn.com>
This is to avoid breaking changes between existing deployments of
extended community for bandwidth encoding. By default FRR uses uint32
to encode bandwidth, which is not as the draft requires (IEEE floating-point).
This switch enables the required encoding per-peer.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
```
exit1-debian-9# show ip bgp large-community-list
(1-500) large-community-list number
LCOMMUNITY_LIST_NAME large-community-list name
large-testas
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
```
exit1-debian-9# show ip bgp community-list ?
(1-500) community-list number
COMMUNITY_LIST_NAME community-list name
testas
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
When bgp receives the admin distance from a redistribution statement
let's store that distance for later usage.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When an EVPN prefix flaps too quickly such that the new advertisement
is received prior to the full processing of the prior withdraw, we may
get into a state where the route doesn't get imported properly into
MAC or IP VRFs. Ensure that we do the route import in such cases.
Suggested-by: Sri Mohana Singamsetty <msingamsetty@vmware.com>
Suggested-by: Ameya Dharkar <adharkar@vmware.com>
Signed-off-by: Vivek Venkatraman <vivek@nvidia.com>
Add a bit of code to allow for auto-completion of the community
alias command when attempting to use it for show commands.
example:
eva(config)# bgp community alias 11:22 FOO
eva(config)# end
eva# show bgp ipv4 uni alias
ALIAS_NAME BGP community alias
FOO
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Some BGP updates received by BGP invite local router to
install a route through itself. The system will not do it, and
the route should be considered as not valid at the earliest.
This case is detected on the zebra, and this detection prevents
from trying to install this route to the local system. However,
the nexthop tracking mechanism is called, and acts as if the route
was valid, which is not the case.
By detecting in BGP that use case, we avoid installing the invalid
routes.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Force the processing of existing network configurations when VRF is
created, otherwise will be skipped in bgp_static_update().
Signed-off-by: Xiao Liang <shaw.leon@gmail.com>
Add a terse option to show bgp summary to shorten output.
Do not show the following information about the BGP
instances: the number of RIB entries, the table version and the used memory.
The "terse" option can be used in combination with the "remote-as", "neighbor",
"failed" and "established" filters, and with the "wide" option as well.
Before patch:
ubuntu# show bgp summary remote-as 123456
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
BGP table version 0
RIB entries 3, using 552 bytes of memory
Peers 5, using 3635 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
% No matching neighbor
Total number of neighbors 5
After patch:
ubuntu# show bgp summary remote-as 123456 terse
IPv4 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 0
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt Desc
10.200.200.2 4 123456 81432 4 0 56092 0 00:00:13 572106 0 N/A
Displayed neighbors 1
Total number of neighbors 4
IPv6 Unicast Summary (VRF default):
BGP router identifier X.X.X.X, local AS number XXX vrf-id 1
% No matching neighbor
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
While installing this route in the EVPN table, make sure all the conditions
mentioned in the draft
https://tools.ietf.org/html/draft-ietf-bess-evpn-prefix-advertisement-11 are
met.
Draft mentions following conditions:
- ESI and gateway IP cannot be both nonzero at the same time.
- ESI, gateway IP, RMAC and VNI label all cannot be 0 at the same time.
If the received EVPN RT-5 route does not meet these conditions, the route is
treated as withdraw.
Signed-off-by: Ameya Dharkar <adharkar@vmware.com>
Gateway IP overlay index is generated for EVPN RT-5 when following CLI is
configured.
router bgp 100 vrf vrf-blue
address-family l2vpn evpn
advertise ipv4 unicast gateway-ip
advertise ipv6 unicast gateway-ip
BGP nexthop of the VRF IP/IPv6 route is set as the gateway IP of the
corresponding EVPN RT-5
Signed-off-by: Ameya Dharkar <adharkar@vmware.com>
We are inconsistently using peer_establiahed(peer) with
sometimes using `peer->status == Established`. Just Convert
over to using the function for consistency.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
BGP configuration changes that imply recomputing the BGP route table
(e.g. modifying route-maps, setting bgp graceful-shutdown) might be a
long time process depending on the size of the BGP table and the
route-map numbers and complexity. For example, setups with full
Internet routes take something like one minute to reprocess all the
prefixes when graceful-shutdown is configured. During this time, a
"show bgp commands" request on vtysh results in blocking the shell until
the soft reconfigure table task is over.
This patch splits bgp_soft_reconfig_table task into thread jobs of 25K
prefixes.
Some tests on a full Internet route setup show that after reconfiguring
route-maps or graceful-shutdown, vtysh is not stucked anymore. We are
now able to request commands like "show bgp summary" after 1 or 2
seconds instead of 30 to 60s.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
For EVPN routes, there is specific logic in place for path selection
surrounding MAC Mobility. For pure type-5 routes, if a route is
advertised with a MED, this is ignored since it ultimately falls inside
of the EVPN specific path selection logic, and ultimately selects the
lower IP address. This change ensures only type-2 routes fall into the
EVPN BGP path selection.
Signed-off-by: Neal Shrader <neal@digitalocean.com>
Show alias name instead of numerical value in `show bgp <prefix>. E.g.:
```
root@exit1-debian-9:~/frr# vtysh -c 'sh run' | grep 'bgp community alias'
bgp community alias 65001:123 community-1
bgp community alias 65001:123:1 lcommunity-1
root@exit1-debian-9:~/frr#
```
```
exit1-debian-9# sh ip bgp 172.16.16.1/32
BGP routing table entry for 172.16.16.1/32, version 21
Paths: (2 available, best #2, table default)
Advertised to non peer-group peers:
65030
192.168.0.2 from home-spine1.donatas.net(192.168.0.2) (172.16.16.1)
Origin incomplete, metric 0, valid, external, best (Neighbor IP)
Community: 65001:12 65001:13 community-1 65001:65534
Large Community: lcommunity-1 65001:123:2
Last update: Fri Apr 16 12:51:27 2021
exit1-debian-9#
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Absolutetly cosmetic change, but let it be consistent with other checks
for optional attributes.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
This is useful to go back in the past and check when was that prefix appeared,
changed, etc.
```
exit1-debian-9# show ip bgp 172.16.16.1/32
BGP routing table entry for 172.16.16.1/32, version 6
Paths: (2 available, best #2, table default)
Advertised to non peer-group peers:
home-spine1.donatas.net(192.168.0.2) home-spine1.donatas.net(2a02:bbd::2)
65030
192.168.0.2 from home-spine1.donatas.net(2a02:bbd::2) (172.16.16.1)
Origin incomplete, metric 0, valid, external
Last update: Thu Apr 8 20:15:25 2021
65030
192.168.0.2 from home-spine1.donatas.net(192.168.0.2) (172.16.16.1)
Origin incomplete, metric 0, valid, external, best (Neighbor IP)
Last update: Thu Apr 8 20:15:25 2021
exit1-debian-9#
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Just to be more informant, copying from Cisco.
```
exit1-debian-9# sh ip bgp
BGP table version is 4, local router ID is 192.168.100.1, vrf id 0
Default local pref 100, local AS 65534
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
RPKI validation codes: V valid, I invalid, N Not found
Network Next Hop Metric LocPrf Weight Path
N*> 10.0.2.0/24 0.0.0.0 0 32768 ?
N*> 192.168.0.0/24 0.0.0.0 0 32768 ?
N*> 192.168.10.0/24 0.0.0.0 0 32768 ?
N*> 192.168.100.1/32 0.0.0.0 0 32768 ?
Displayed 4 routes and 4 total paths
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
set_vpn_nexthop/no_set_vpn_nexthop were failing due to missing
declarations and unused variables.
This adds the missing declaration and removes unused variables.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
New and improved submission for this commit -- updated to accommodate
changes from 4027d19b0.
Adds support for 'rd all' matching for EVPN and L3VPN show commands.
Introduces evpn_show_route_rd_all_macip().
Cleans up some show commands to use SHOW_DISPLAY string constants.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
During Review it was suggested that appending rpki_
to curr_state and target_state would be better
variable names. Instead of going and fixing
3 or so commits up. Just do this one.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add the ability for the end operator to query the state of valid
or invalid or no information rpki prefix information.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When displaying data about the rpki state, use the
string `rpki validation-state` instead of `validation-state:`
to avoid confusion with `(valid)`
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Setup a mh_info indirection in the path extra. This has been done to
avoid increasing evpn route's path size to add new (type based) pointers
in path_info_extra.
Ticket: CM-31398
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
There are two changes in this commit -
1. Maintain a list of global MAC-IP routes per-ES. This list is maintained
for quick processing on the following events -
a. When the first VTEP/PE becomes active in the ES-VRF, the L3 NHG is
activated and the route can be sent to zebra.
b. When there are no active PEs in the ES-VRF the L3 NHG is
de-activated and -
- If the ES is present in the VRF -
The route is not installed in zebra as there are no active PEs for
the ES-VRF
- If the ES is not present in the VRF -
The route is installed with a flat multi-path list i.e. without L3NHG.
This is to handle the case where there are no locally attached L2VNIs
on the ES (for that tenant VRF).
2. Reinstall VRF route when an ES is installed or uninstalled in a
tenant VRF (the global MAC-IP list in #1 is used for this purpose also).
If an ES is present in the VRF we use L3NHG to enable fast-failover of
routed traffic.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
This new BGP configuration is akin to "bgp bestpath aspath
multipath-relax". When applied, paths learned from different peer types
will be eligible to be considered for multipath (ECMP). Paths from all
of eBGP, iBGP, and confederation peers may be included in multipaths
if they are otherwise equal cost.
This change preserves the existing bestpath behavior of step 10's result
being returned, not the result from steps 8 and 9, in the case where
both 8+9 and 10 determine a winner.
Signed-off-by: Joanne Mikkelson <jmmikkel@arista.com>
Adds support for 'rd all' matching for EVPN and L3VPN show commands.
Introduces evpn_show_route_rd_all_macip().
Cleanup some show commands to use SHOW_DISPLAY string constants.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
When dumping data about prefixes in bgp. Let's dump the
rpki validation state as well:
Output if rpki is turned on:
janelle# show rpki prefix 2003::/19
Prefix Prefix Length Origin-AS
2003:: 19 - 19 3320
janelle# show bgp ipv6 uni 2003::/19
BGP routing table entry for 2003::/19
Paths: (1 available, best #1, table default)
Not advertised to any peer
15096 6939 3320
::ffff:4113:867a from 65.19.134.122 (193.72.216.231)
(fe80::e063:daff:fe79:1dab) (used)
Origin IGP, valid, external, best (First path received), validation-state: valid
Last update: Sat Mar 6 09:20:51 2021
janelle# show rpki prefix 8.8.8.0/24
Prefix Prefix Length Origin-AS
janelle# show bgp ipv4 uni 8.8.8.0/24
BGP routing table entry for 8.8.8.0/24
Paths: (1 available, best #1, table default)
Advertised to non peer-group peers:
100.99.229.142
15096 6939 15169
65.19.134.122 from 65.19.134.122 (193.72.216.231)
Origin IGP, valid, external, best (First path received), validation-state: not found
Last update: Sat Mar 6 09:21:25 2021
Example output when rpki is not configured:
eva# show bgp ipv4 uni 8.8.8.0/24
BGP routing table entry for 8.8.8.0/24
Paths: (1 available, best #1, table default)
Advertised to non peer-group peers:
janelle(192.168.161.137)
64539 15096 6939 15169
192.168.161.137(janelle) from janelle(192.168.161.137) (192.168.44.1)
Origin IGP, valid, external, bestpath-from-AS 64539, best (First path received)
Last update: Sat Mar 6 09:33:51 2021
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
'show bgp l2vpn evpn statistics' was returning 0 for all stats
because bgp_table_stats_walker bailed out if afi != AFI_IP or AFI_IP6.
Add case condition to catch AFI_L2VPN.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
If we are filtering a route due to any of the filter reasons
we should not be setting the BGP_NODE_FIB_INSTALL_FIB_PENDING
flag. This is especially evident with say a loopback that
is covered by a network statement. When we receive the route
back from our peer we should not be setting the
BGP_NODE_FIB_INSTALL_PENDING flag on it.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
'show bgp ipv[46] vpn neighbors ... advertised-routes' was displaying
empty output due to new command syntax using show_adj_routes() which
assumed each bgp_table was single-tier (not nested). This fixes that
assumption for safis with a two-tier bgp_table (SAFI_MPLS_VPN,
SAFI_ENCAP, and SAFI_EVPN).
Before:
ub18# show bgp ipv6 vpn neighbors 2001:db8:cafe::2 advertised-routes
ub18#
After:
ub20# show bgp ipv6 vpn neighbors 2001:db8:cafe::1 advertised-routes
BGP table version is 2, local router ID is 100.64.0.222, vrf id 0
Default local pref 100, local AS 1
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
Route Distinguisher: 30:30
*> 2::2/128 :: 0 100 32768 i
*> 2::22/128 :: 0 100 32768 i
Route Distinguisher: 33:33
*> 2::2/128 :: 0 100 32768 i
*> 2::22/128 :: 0 100 32768 i
Total number of prefixes 4
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
`same_attr` has been computed and `hook_call(bgp_process)` (calling
BMP module) would not change it. We could reuse the value to filter
same attribute updates, avoiding an extra comparison.
Signed-off-by: zyxwvu Shi <i@shiyc.cn>
Already not necessary, because if BGP aggregator AS attribute is with
value of 0, then the attribute is already discarded at early processing.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Description:
clear ip bgp dampening was not triggering the route
calculation for the prefix, Due to this prefix are not install in
RIB(Zebra) and not adv to neighbor
Problem Description/Summary :
clear ip bgp dampening was not triggering the route
calculation for the prefix, Due to this prefix are not install in
RIB(Zebra) and not adv to neighbor
Fix: When clear ip bgp dampening, route are put for route-calculation as
that it is install in the Zebra and adv to neighbor.
Signed-off-by: sudhanshukumar22 <sudhanshu.kumar@broadcom.com>
If we are using a nexthop for a MPLS VPN route make sure the
nexthop is over a labeled path. This new check mirrors the one
in validate_paths (where routes are enabled when a nexthop
becomes reachable). The check is introduced to the code path
where routes are added and the nexthop is looked up.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
community_str2com("no-export"); returns ALWAYS non-NULL.
If NULL returned here, we really have a bigger problems in the call path.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
RFC says to prevent propagation of the prefix outside the local AS.
So, let's use NO_EXPORT.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Issue: bgpd got kill due to out of memory, when show bgp
neighbor json and show ip bgp neighbor <ip> routes json
commands executed multiple times in a setup having 320554
routes.
RCA: Heap allocated for bgpd keeps increasing. This is verified
using top command and show memory command.
Memleak Fix-1: show ip bgp route json command
When dumping a large bit of table data via bgp_show_route
and if there is no information to display for a particular
struct bgp_node *` the data allocated via json_object_new_array()
is not freed. This is resolved now.
Memleak Fix-2:
The function bgp_peer_counts() doesn't free the memory allocated for
json_loop when there is No such neighbor or address family. This is
fixed now.
Signed-off-by: Sarita Patra <saritap@vmware.com>
rfc7999:
A BGP speaker receiving an announcement tagged with the BLACKHOLE
community SHOULD add the NO_ADVERTISE or NO_EXPORT community as
defined in [RFC1997], or a similar community, to prevent propagation
of the prefix outside the local AS. The community to prevent
propagation SHOULD be chosen according to the operator's routing
policy.
Sent:
```
router bgp 65534
no bgp ebgp-requires-policy
neighbor 192.168.0.2 remote-as 65030
!
address-family ipv4 unicast
redistribute connected
neighbor 192.168.0.2 route-map spine out
exit-address-family
!
!
ip prefix-list self seq 5 permit 192.168.100.1/32
!
route-map spine permit 10
match ip address prefix-list self
set community blackhole
!
```
Received:
```
spine1-debian-9# show ip bgp 192.168.100.1/32
BGP routing table entry for 192.168.100.1/32
Paths: (1 available, best #1, table default, inform peer to blackhole prefix)
Not advertised to any peer
65534
192.168.0.1 from 192.168.0.1 (192.168.100.1)
Origin incomplete, metric 0, valid, external, best (First path received)
Community: blackhole no-advertise
Last update: Thu Jan 21 12:56:39 2021
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
When bgp is using wait for install semantics it would be nice
to be able to debug it when it is running.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
To prepare for fixing an issue where labels do not get released back
to the labelpool when the route is deleted some refactoring is
necessary. There are 2 parts to this.
1. restructure the code to remove the circular nature of label
allocations via the labelpool and decouple the label type decision
from the notification fo the FEC.
The code to notify the FEC association to zebra has been split out
into a separate function so that it can be called from the synchronous
path (for registration of index-based labels and de-registration of all
labels), and from the asynchronous path where we need to wait for a
callback from the labelpool code with a label allocation.
The decision about whether we are using an index-based label or an
allocated label is reflected in the state of the BGP_NODE_LABEL_REQUESTED
flag so the checks on the path_info in the labelpool callback code are
no longer required.
2. change the owned of a labelpool allocated label from the path info
structure to the bgp_dest structure. This allows labels to be released
(in a subsequent commit) when the owner (bgp_dest) goes away.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
Remove awful test of a strmatch against a call to get_afi_safi_str.
These are the easy ones as that the real decision point is/was
underneath this test. This is just duplicate expensive testing.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Use user provided AD for local routes (aggregate).
address-family ipv4 unicast
distance bgp 20 200 210
network 47.2.2.8/30
aggregate-address 51.1.0.0/16
Testing Done:
Before aggr route uses default 200 AD even user provided local AD.
B>* 51.1.0.0/16 [200/0] unreachable (blackhole), weight 1, 00:01:14
After:
B>* 51.1.0.0/16 [210/0] unreachable (blackhole), weight 1, 00:00:01
Signed-off-by: Chirag Shah <chirag@nvidia.com>
bgp aggregate address installs route with self peer which
can have peer->su of unspecifed type.
bgp_distance_apply bailed out as it fails to parse
sockunion2hostprefix for af type unspec.
config:
address-family ipv4 unicast
aggregate-address 50.1.0.0/16 summary-only
Testing Done:
Before:
B>* 50.1.0.0/16 [20/0] unreachable (blackhole), weight 1, 00:00:02
After:
B>* 50.1.0.0/16 [200/0] unreachable (blackhole), weight 1, 00:01:28
Signed-off-by: Chirag Shah <chirag@nvidia.com>
1. MAC-IP routes in the VPN routing table are linked to the
destination ES for efficient handling for remote ES link flaps.
2. Only MAC-IP paths whose nexthops are active (added via EAD-ES)
are imported into the VRF routing table.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
The return from sockunion2hostprefix tells us if the conversion
succeeded or not. There are places in the code where we
always assume that it just `works`, since it can fail
notice and try to do the right thing.
Please note that failure of this function for most cases
of sockunion2hostprefix is highly highly unlikely as that
the sockunion was already created and tested elsewhere
it's just that this function can fail.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Convert usage of the attr->evpn_overlay to get/set functionality.
Future commits will allow us to abstract this data to when
we actually need it for the `struct attr`.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Abstract the access of `attr->cluster` to appropriate
accessor/set functionality.
Future commits will allow us to move this data around
to make `struct attr` smaller.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add an accessor for the bgp_attr.pmsi_tnl_type to allow
us to abstract where it is. Every attribute is paying
the price of this bit of data as part of `struct bgp_attr`
In the future we'll move it elsewhere.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When we delete the bgp_path_info_extra data structure free
the aggr_suppressors data structure that was left dangling.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
We are temporarily allocing memory to show lcommunity
information. We then immediately drop it. Account for
that memory properly.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The route_map_object_t was being used to track what protocol we were
being called against. But each protocol was only ever calling itself.
So we had a variable that was only ever being passed in from route_map_apply
that had to be carried against and everyone was testing if that variable
was for their own stack.
Clean up this route_map_object_t from the entire system. We should
speed some stuff up. Yes I know not a bunch but this will add up.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Commit: 26742171e6
Mistakenly reversed the logic for the test on the list length
when it was removed. Fix this.
Additionally limit for loop to stop when we know there are no
more items to process that have the BGP_NODE_SELECT_DEFER flag.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
* Process FIB update in bgp_zebra_route_notify_owner() and call
group_announce_route() if route is installed
* When bgp update is received for a route which is not installed earlier
(flag BGP_NODE_FIB_INSTALLED is not set) and suppress fib is enabled
set the flag BGP_NODE_FIB_INSTALL_PENDING to indicate fib install is
pending for the route. The route will be advertised when zebra send
ZAPI_ROUTE_INSTALLED status.
* The advertisement delay (BGP_DEFAULT_UPDATE_ADVERTISEMENT_TIME)
is added to allow more routes to be sent in single update message.
This is required since zebra sends route notify message for each route.
The delay will be applied to update group timer which advertises
routes to peers.
Signed-off-by: kssoman <somanks@gmail.com>
We are allocating temporary memory for information about
what to process in this thread, which is not being cleaned
up on thread cancelling.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The `struct listnode *rt_node` data structure is adding
8 bytes of size to the `struct bgp_dest`. This is a large
amount of data for a flag we are already setting on each
node for this. Just set the flag and use that to figure
out who we are doing graceful restart on.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When generating a config with 1 prefix:
BGP IPv4 Unicast RIB statistics
Total Advertisements : 0
Total Prefixes : 0
Average prefix length : 0.00
Unaggregateable prefixes : 0
Maximum aggregateable prefixes: 0
BGP Aggregate advertisements : 0
Address space advertised : 0
% announced : 0.00
/8 equivalent : 0.00
/24 equivalent : 0.00
Advertisements with paths : 0
Longest AS-Path (hops) : 0
Average AS-Path length (hops) : 0.00
Largest AS-Path (bytes) : 0
Average AS-Path size (bytes) : 0.00
Highest public ASN : 0
eva# show bgp ipv4 uni summ
BGP router identifier 10.10.3.11, local AS number 329 vrf-id 0
BGP table version 1
RIB entries 1, using 192 bytes of memory
Peers 1, using 23 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt
192.168.161.131 4 60000 24 27 0 0 0 00:01:05 (Policy) 1
Total number of neighbors 1
We are not displaying it in the statistics data. This is because FRR is walking the associated
table and comparing the current dest to the top of the tree. I have no idea why this is
the case as that when you have 1 prefix you only have 1 node in your tree. Looking at the
code this is the original code that was imported in 2006. I cannot think of any reason why
FRR needs to exclude this particular node.
Fixed:
eva# show bgp ipv4 uni summ
BGP router identifier 10.10.3.11, local AS number 329 vrf-id 0
BGP table version 1
RIB entries 1, using 192 bytes of memory
Peers 1, using 23 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt
192.168.161.131 4 60000 24 27 0 0 0 00:01:05 (Policy) 1
Total number of neighbors 1
eva# show bgp ipv4 statistics
BGP IPv4 Unicast RIB statistics (VRF default)
Total Advertisements : 1
Total Prefixes : 1
Average prefix length : 32.00
Unaggregateable prefixes : 1
Maximum aggregateable prefixes: 0
BGP Aggregate advertisements : 0
Address space advertised : 1
% announced : 0.00
/8 equivalent : 0.00
/24 equivalent : 0.00
Advertisements with paths : 1
Longest AS-Path (hops) : 0
Average AS-Path length (hops) : 0.00
Largest AS-Path (bytes) : 0
Average AS-Path size (bytes) : 0.00
Highest public ASN : 0
eva#
Fixes: #7422
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Changes implement dampening profiles for peers and peer groups. This is
achieved by introducing the possibility to have multible existing
dampening configurations with their own sets of parameters and lists of
associated paths.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
We were missing the help docstring for IPV6 under the
distance src command in for bgp.
```
[root@alfred frr-2]# /usr/lib/frr/bgpd --log stdout --log-level debug
2020/10/30 16:02:26 BGP: Ran out of docstring while parsing '[no] distance (1-255) <A.B.C.D/M | X:X::X:X/M>$prefix [WORD$acl]'
2020/10/30 16:02:26 BGP: Ran out of docstring while parsing '[no] distance (1-255) <A.B.C.D/M | X:X::X:X/M>$prefix [WORD$acl]'
2020/10/30 16:02:26 BGP: Ran out of docstring while parsing '[no] distance (1-255) <A.B.C.D/M | X:X::X:X/M>$prefix [WORD$acl]'
2020/10/30 16:02:26 BGP: Ran out of docstring while parsing '[no] distance (1-255) <A.B.C.D/M | X:X::X:X/M>$prefix [WORD$acl]'
2020/10/30 16:02:26 BGP: Ran out of docstring while parsing '[no] distance (1-255) <A.B.C.D/M | X:X::X:X/M>$prefix [WORD$acl]'
```
Signed-off-by: Stephen Worley <sworley@nvidia.com>
The problem is that only prefixes were handled and any other `match`
commands were ignored. Let's do not forget them as well.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Sample Configuration with prefix-list and community match rules
---------------------------------------------------------------
R1 ------- R2(DUT) ------- R3
Router2# show running-config
Building configuration...
Current configuration:
!
frr version 7.6-dev-MyOwnFRRVersion
frr defaults traditional
hostname router
log file /var/log/frr/bgpd.log
log syslog informational
hostname Router2
service integrated-vtysh-config
!
debug bgp updates in
debug bgp updates out
!
debug route-map
!
ip route 20.20.0.0/16 blackhole
ipv6 route 2001:db8::200/128 blackhole
!
interface enp0s9
ip address 10.10.10.2/24
!
interface enp0s10
ip address 10.10.20.2/24
!
interface lo
ip address 2.2.2.2/32
!
router bgp 2
bgp log-neighbor-changes
no bgp ebgp-requires-policy
neighbor 10.10.10.1 remote-as 1
neighbor 10.10.20.3 remote-as 3
!
address-family ipv4 unicast
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.20.3 soft-reconfiguration inbound
neighbor 10.10.20.3 advertise-map ADV-MAP non-exist-map EXIST-MAP
exit-address-family
!
ip prefix-list DEFAULT seq 5 permit 1.1.1.5/32
ip prefix-list DEFAULT seq 10 permit 1.1.1.1/32
ip prefix-list EXIST seq 5 permit 10.10.10.10/32
ip prefix-list DEFAULT-ROUTE seq 5 permit 0.0.0.0/0
ip prefix-list IP1 seq 5 permit 10.139.224.0/20
ip prefix-list T2 seq 5 permit 1.1.1.5/32
!
bgp community-list standard DC-ROUTES seq 5 permit 64952:3008
bgp community-list standard DC-ROUTES seq 10 permit 64671:501
bgp community-list standard DC-ROUTES seq 15 permit 64950:3009
bgp community-list standard DEFAULT-ROUTE seq 5 permit 65013:200
!
route-map ADV-MAP permit 10
match ip address prefix-list IP1
!
route-map ADV-MAP permit 20
match community DC-ROUTES
!
route-map EXIST-MAP permit 10
match community DEFAULT-ROUTE
match ip address prefix-list DEFAULT-ROUTE
!
line vty
!
end
Router2#
Router2# show ip bgp 0.0.0.0
BGP routing table entry for 0.0.0.0/0
Paths: (1 available, best #1, table default)
Advertised to non peer-group peers:
10.10.10.1 10.10.20.3
1
10.10.10.1 from 10.10.10.1 (10.139.224.1)
Origin IGP, metric 0, valid, external, best (First path received)
Community: 64848:3011 65011:200 65013:200
Last update: Tue Oct 6 02:39:42 2020
Router2#
Sample output with non-exist-map when default route present in table
--------------------------------------------------------------------
Router2# show ip bgp
BGP table version is 4, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 0.0.0.0/0 10.10.10.1 0 0 1 i
*> 1.1.1.1/32 10.10.10.1 0 0 1 i
*> 1.1.1.5/32 10.10.10.1 0 0 1 i
*> 10.139.224.0/20 10.10.10.1 0 0 1 ?
Displayed 4 routes and 4 total paths
Router2# show ip bgp neighbors 10.10.20.3 advertised-routes
BGP table version is 4, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 0.0.0.0/0 0.0.0.0 0 1 i
*> 1.1.1.5/32 0.0.0.0 0 1 i <<<<<<<<< non-exist-map : 0.0.0.0/0 is present so, 10.139.224.0/20 not advertised
Total number of prefixes 2
Sample output with non-exist-map when default route not present in table
------------------------------------------------------------------------
Router2# show ip bgp
BGP table version is 5, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.1/32 10.10.10.1 0 0 1 i
*> 1.1.1.5/32 10.10.10.1 0 0 1 i
*> 10.139.224.0/20 10.10.10.1 0 0 1 ?
Displayed 3 routes and 3 total paths
Router2#
Router2#
Router2# show ip bgp neighbors 10.10.20.3 advertised-routes
BGP table version is 5, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.1/32 0.0.0.0 0 1 i
*> 1.1.1.5/32 0.0.0.0 0 1 i
*> 10.139.224.0/20 0.0.0.0 0 1 ? <<<<<<<<< non-exist-map : 0.0.0.0/0 is not present so, 10.139.224.0/20 advertised
Total number of prefixes 3
Router2#
Sample output with exist-map when default route present in table
--------------------------------------------------------------------
Router2# show ip bgp
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 0.0.0.0/0 10.10.10.1 0 0 1 i
*> 1.1.1.1/32 10.10.10.1 0 0 1 i
*> 1.1.1.5/32 10.10.10.1 0 0 1 i
*> 10.139.224.0/20 10.10.10.1 0 0 1 ?
Displayed 4 routes and 4 total paths
Router2#
Router2#
Router2#
Router2#
Router2# show ip bgp neighbors 10.10.20.3 advertised-routes
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 0.0.0.0/0 0.0.0.0 0 1 i
*> 1.1.1.1/32 0.0.0.0 0 1 i
*> 1.1.1.5/32 0.0.0.0 0 1 i
*> 10.139.224.0/20 0.0.0.0 0 1 ? <<<<<<<<< exist-map : 0.0.0.0/0 is present so, 10.139.224.0/20 advertised
Total number of prefixes 4
Router2#
Sample output with exist-map when default route not present in table
--------------------------------------------------------------------
Router2# show ip bgp
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.1/32 10.10.10.1 0 0 1 i
*> 1.1.1.5/32 10.10.10.1 0 0 1 i
*> 10.139.224.0/20 10.10.10.1 0 0 1 ?
Displayed 3 routes and 3 total paths
Router2#
Router2#
Router2#
Router2# show ip bgp neighbors 10.10.20.3 advertised-routes
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.5/32 0.0.0.0 0 1 i <<<<<<<<< exist-map : 0.0.0.0/0 is not present so, 10.139.224.0/20 not advertised
Total number of prefixes 1
Router2#
Signed-off-by: Madhuri Kuruganti <k.madhuri@samsung.com>
Sample configuration along with route-map filter
------------------------------------------------
Router2# show running-config
Building configuration...
Current configuration:
!
frr version 7.6-dev-MyOwnFRRVersion
frr defaults traditional
hostname router
log file /var/log/frr/bgpd.log
log syslog informational
hostname Router2
service integrated-vtysh-config
!
debug bgp updates in
debug bgp updates out
!
debug route-map
!
ip route 200.200.0.0/16 blackhole
ipv6 route 2001:db8::200/128 blackhole
!
interface enp0s9
ip address 10.10.10.2/24
!
interface enp0s10
ip address 10.10.20.2/24
!
interface lo
ip address 2.2.2.2/24
ipv6 address 2001:db8::2/128
!
router bgp 2
bgp log-neighbor-changes
no bgp ebgp-requires-policy
neighbor 10.10.10.1 remote-as 1
neighbor 10.10.20.3 remote-as 3
!
address-family ipv4 unicast
network 2.2.2.0/24
network 200.200.0.0/16
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.10.1 route-map RMAP_PERMIT_100 out
neighbor 10.10.10.1 advertise-map ADVERTISE non-exist-map CONDITION
neighbor 10.10.20.3 soft-reconfiguration inbound
exit-address-family
!
address-family ipv6 unicast
network 2001:db8::2/128
network 2001:db8::200/128
neighbor 10.10.10.1 activate
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.10.1 route-map CONDITION_6 out
neighbor 10.10.10.1 advertise-map ADVERTISE_6 non-exist-map CONDITION_6
neighbor 10.10.20.3 activate
neighbor 10.10.20.3 soft-reconfiguration inbound
exit-address-family
!
access-list CONDITION seq 5 permit 3.3.3.0/24
access-list ADVERTISE seq 6 permit 200.200.0.0/16
access-list ADVERTISE seq 7 permit 20.20.0.0/16
access-list ADVERTISE seq 5 permit 2.2.2.0/24
access-list RMAP_PERMIT_100 seq 4 permit 100.100.0.0/16
!
ipv6 access-list ADVERTISE_6 seq 5 permit 2001:db8::2/128
ipv6 access-list CONDITION_6 seq 5 permit 2001:db8::3/128
!
route-map ADVERTISE permit 10
match ip address ADVERTISE
!
route-map CONDITION permit 10
match ip address CONDITION
!
route-map ADVERTISE_6 permit 10
match ipv6 address ADVERTISE_6
!
route-map CONDITION_6 permit 10
match ipv6 address CONDITION_6
!
route-map RMAP_PERMIT_100 permit 10
match ip address RMAP_PERMIT_100
!
line vty
!
end
Sample output when non-exist-map prefixes present in BGP table
--------------------------------------------------------------
Router2# show ip bgp all wide
For address family: IPv4 Unicast
BGP table version is 5, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 10.10.10.1 0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 3.3.3.0/24 10.10.20.3 0 0 3 i
*> 100.100.0.0/16 10.10.20.3 0 0 3 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Displayed 5 routes and 5 total paths
For address family: IPv6 Unicast
BGP table version is 4, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 fe80::a00:27ff:fecb:ad57 0 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::3/128 fe80::a00:27ff:fe76:6738 0 0 3 i
*> 2001:db8::200/128 :: 0 32768 i
Displayed 4 routes and 4 total paths
Router2#
Router2#
Router2#
Router2#
Router2# show ip bgp all neighbors 10.10.10.1 advertised-routes wide
For address family: IPv4 Unicast
BGP table version is 5, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 100.100.0.0/16 0.0.0.0 0 3 i
Total number of prefixes 1
For address family: IPv6 Unicast
BGP table version is 4, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::3/128 :: 0 3 i
Total number of prefixes 1
Router2#
Sample output when non-exist-map prefixes not present in BGP table
------------------------------------------------------------------
Router2# show ip bgp all wide
For address family: IPv4 Unicast
BGP table version is 6, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 10.10.10.1 0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 100.100.0.0/16 10.10.20.3 0 0 3 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Displayed 4 routes and 4 total paths
For address family: IPv6 Unicast
BGP table version is 5, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 fe80::a00:27ff:fecb:ad57 0 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::200/128 :: 0 32768 i
Displayed 3 routes and 3 total paths
Router2#
Router2# show ip bgp all neighbors 10.10.10.1 advertised-routes wide
For address family: IPv4 Unicast
BGP table version is 6, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 100.100.0.0/16 0.0.0.0 0 3 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Total number of prefixes 3
For address family: IPv6 Unicast
BGP table version is 5, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::2/128 :: 0 32768 i
Total number of prefixes 1
Router2#
Signed-off-by: Madhuri Kuruganti <k.madhuri@samsung.com>
Implemented as per the feature description given in the source link.
Descriprion:
The BGP conditional advertisement feature uses the non-exist-map or exist-map
and the advertise-map keywords of the neighbor advertise-map command in order
to track routes by the route prefix.
non-exist-map :
If a route prefix is not present in output of the non-exist-map command, then
the route specified by the advertise-map command is announced.
exist-map :
If a route prefix is present in output of the exist-map command, then the route
specified by the advertise-map command is announced.
The conditional BGP announcements are sent in addition to the normal
announcements that a BGP router sends to its peers.
The conditional advertisement process is triggered by the BGP scanner process,
which runs every 60 seconds. This means that the maximum time for the conditional
advertisement to take effect is 60 seconds. The conditional advertisement can take
effect sooner, depending on when the tracked route is removed from the BGP table
and when the next instance of the BGP scanner occurs.
Sample Configuration on DUT
---------------------------
Router2# show running-config
Building configuration...
Current configuration:
!
frr version 7.6-dev-MyOwnFRRVersion
frr defaults traditional
hostname router
log file /var/log/frr/bgpd.log
log syslog informational
hostname Router2
service integrated-vtysh-config
!
debug bgp updates in
debug bgp updates out
!
debug route-map
!
ip route 200.200.0.0/16 blackhole
ipv6 route 2001:db8::200/128 blackhole
!
interface enp0s9
ip address 10.10.10.2/24
!
interface enp0s10
ip address 10.10.20.2/24
!
interface lo
ip address 2.2.2.2/24
ipv6 address 2001:db8::2/128
!
router bgp 2
bgp log-neighbor-changes
no bgp ebgp-requires-policy
neighbor 10.10.10.1 remote-as 1
neighbor 10.10.20.3 remote-as 3
!
address-family ipv4 unicast
network 2.2.2.0/24
network 200.200.0.0/16
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.10.1 advertise-map ADVERTISE non-exist-map CONDITION
neighbor 10.10.20.3 soft-reconfiguration inbound
exit-address-family
!
address-family ipv6 unicast
network 2001:db8::2/128
network 2001:db8::200/128
neighbor 10.10.10.1 activate
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.10.1 advertise-map ADVERTISE_6 non-exist-map CONDITION_6
neighbor 10.10.20.3 activate
neighbor 10.10.20.3 soft-reconfiguration inbound
exit-address-family
!
access-list CONDITION seq 5 permit 3.3.3.0/24
access-list ADVERTISE seq 5 permit 2.2.2.0/24
access-list ADVERTISE seq 6 permit 200.200.0.0/16
access-list ADVERTISE seq 7 permit 20.20.0.0/16
!
ipv6 access-list ADVERTISE_6 seq 5 permit 2001:db8::2/128
ipv6 access-list CONDITION_6 seq 5 permit 2001:db8::3/128
!
route-map ADVERTISE permit 10
match ip address ADVERTISE
!
route-map CONDITION permit 10
match ip address CONDITION
!
route-map ADVERTISE_6 permit 10
match ipv6 address ADVERTISE_6
!
route-map CONDITION_6 permit 10
match ipv6 address CONDITION_6
!
line vty
!
end
Router2#
Withdraw when non-exist-map prefixes present in BGP table:
----------------------------------------------------------
Router2# show ip bgp all wide
For address family: IPv4 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 10.10.10.1 0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 3.3.3.0/24 10.10.20.3 0 0 3 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Displayed 4 routes and 4 total paths
For address family: IPv6 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 fe80::a00:27ff:fecb:ad57 0 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::3/128 fe80::a00:27ff:fe76:6738 0 0 3 i
*> 2001:db8::200/128 :: 0 32768 i
Displayed 4 routes and 4 total paths
Router2#
Router2# show ip bgp neighbors 10.10.10.1
BGP neighbor is 10.10.10.1, remote AS 1, local AS 2, external link
!--- Output suppressed.
For address family: IPv4 Unicast
Update group 9, subgroup 5
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION, Advertise-map *ADVERTISE, status: Withdraw
1 accepted prefixes
For address family: IPv6 Unicast
Update group 10, subgroup 6
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION_6, Advertise-map *ADVERTISE_6, status: Withdraw
1 accepted prefixes
!--- Output suppressed.
Router2#
Here 2.2.2.0/24 & 200.200.0.0/16 (prefixes in advertise-map) are withdrawn
by conditional advertisement scanner as the prefix(3.3.3.0/24) specified
by non-exist-map is present in BGP table.
Router2# show ip bgp all neighbors 10.10.10.1 advertised-routes wide
For address family: IPv4 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 0.0.0.0 0 1 i
*> 3.3.3.0/24 0.0.0.0 0 3 i
Total number of prefixes 2
For address family: IPv6 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 :: 0 1 i
*> 2001:db8::3/128 :: 0 3 i
*> 2001:db8::200/128 :: 0 32768 i
Total number of prefixes 3
Router2#
Advertise when non-exist-map prefixes not present in BGP table:
---------------------------------------------------------------
After Removing 3.3.3.0/24 (prefix present in non-exist-map),
2.2.2.0/24 & 200.200.0.0/16 (prefixes present in advertise-map) are advertised
Router2# show ip bgp all wide
For address family: IPv4 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 10.10.10.1 0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Displayed 3 routes and 3 total paths
For address family: IPv6 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 fe80::a00:27ff:fecb:ad57 0 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::200/128 :: 0 32768 i
Displayed 3 routes and 3 total paths
Router2#
Router2# show ip bgp neighbors 10.10.10.1
!--- Output suppressed.
For address family: IPv4 Unicast
Update group 9, subgroup 5
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION, Advertise-map *ADVERTISE, status: Advertise
1 accepted prefixes
For address family: IPv6 Unicast
Update group 10, subgroup 6
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION_6, Advertise-map *ADVERTISE_6, status: Advertise
1 accepted prefixes
!--- Output suppressed.
Router2#
Router2# show ip bgp all neighbors 10.10.10.1 advertised-routes wide
For address family: IPv4 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 0.0.0.0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Total number of prefixes 3
For address family: IPv6 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 :: 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::200/128 :: 0 32768 i
Total number of prefixes 3
Router2#
Signed-off-by: Madhuri Kuruganti <k.madhuri@samsung.com>
Convert IPv4 and IPv6 unicast address family clis
to transactional clis and implementation of
northbound callbacks.
Signed-off-by: Chirag Shah <chirag@nvidia.com>
- tracepoint() -> frrtrace()
- tracelog() -> frrtracelog()
- tracepoint_enabled() -> frrtrace_enabled()
Also removes copypasta'd #ifdefs for those LTTng macros, those are
handled in lib/trace.h
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Replace all lib/thread cancel macros, use thread_cancel()
everywhere. Only the THREAD_OFF macro and thread_cancel() api are
supported. Also adjust thread_cancel_async() to NULL caller's pointer (if
present).
Signed-off-by: Mark Stapp <mjs@voltanet.io>
Instead of just counting the route suppressions, keep a reference for
all aggregations that are doing it. It should help the with the
following problems:
- Which aggregation suppressed the route.
- Double suppression
- Double unsuppression
- Avoids calling `bgp_process` if already suppressed/unsuppressed.
- Easier code maintenance and understanding
This also fixes a crash when modifying a route map that is
associated with a working aggregate-address.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Add new aggregate-address option to selectively suppress routes based
on route map results.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
We currently have a global process queue for handling route
updates in bgp. This is fine, in general, except there are
places and times where we plug the queue for no new work
during certain peer states of bgp update delay. If we
happen to be processing multiple bgp instances on startup
why do we want to stop processing in vrf A when vrf B
is in a bit of a pickle?
Also this separation will allow us to start forward thinking
about how to fully integrate pthreads into route processing
in bgp.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Create appropriate accessor functions for the rn->lock
data. We should be accessing this data through accessor
functions since it is private data to the data structure.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
bgp_show_neighbor_route() was rewriting safi from LU to uni
before checking if the peer was enabled for LU. This resulted
in the peer's address-family check looking for unicast, which
would always fail for LU peers since unicast + LU are
mutually-exclusive AFIs.
This moves this safi reassignment after the peer AFI check,
ensuring that the peer's address-family check looks for LU
while the call to bgp_show() still uses uni.
-- highlights from manual testing
config:
router bgp 2
neighbor 1.1.1.1 remote-as external
neighbor 1.1.1.1 disable-connected-check
neighbor 1.1.1.1 update-source 2.2.2.2
!
address-family ipv4 unicast
no neighbor 1.1.1.1 activate
exit-address-family
!
address-family ipv4 labeled-unicast
neighbor 1.1.1.1 activate
exit-address-family
before:
spine01# show bgp ipv4 unicast neighbors 1.1.1.1 routes
% No such neighbor or address family
spine01# show bgp ipv4 labeled-unicast neighbors 1.1.1.1 routes
% No such neighbor or address family
after:
spine01# show bgp ipv4 unicast neighbors 1.1.1.1 routes
% No such neighbor or address family
spine01# show bgp ipv4 label neighbors 1.1.1.1 routes
BGP table version is 1, local router ID is 2.2.2.2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 11.11.11.11/32 1.1.1.1 0 0 1 i
Displayed 1 routes and 1 total paths
Signed-off-by: Trey Aspelund <taspelund@cumulusnetworks.com>
if (pcout > (pcount * peer->max_threshold[afi][safi] / 100 ))
is always true. So the very first route received will always
trigger the warning. We actually want the warning to happen
when we hit the threshold.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Current code in bgp bestpath selection would accept the newest
locally originated path as the best path. Making the selection
non-deterministic. Modify the code to always come to the
same bestpath conclusion when you have multiple locally originated
paths in bestpath selection.
Before:
eva# conf
eva(config)# router bgp 323
eva(config-router)# address-family ipv4 uni
eva(config-router-af)# redistribute connected
eva(config-router-af)# network 192.168.161.0/24
eva(config-router-af)# do show bgp ipv4 uni 192.168.161.0
BGP routing table entry for 192.168.161.0/24
Paths: (2 available, best #1, table default)
Not advertised to any peer
Local
0.0.0.0(eva) from 0.0.0.0 (192.168.161.245)
Origin IGP, metric 0, weight 32768, valid, sourced, local, bestpath-from-AS Local, best (Origin)
Last update: Wed Sep 16 15:03:03 2020
Local
0.0.0.0(eva) from 0.0.0.0 (192.168.161.245)
Origin incomplete, metric 0, weight 32768, valid, sourced
Last update: Wed Sep 16 15:02:52 2020
eva(config-router-af)# no redistribute connected
eva(config-router-af)# do show bgp ipv4 uni 192.168.161.0
BGP routing table entry for 192.168.161.0/24
Paths: (1 available, best #1, table default)
Not advertised to any peer
Local
0.0.0.0(eva) from 0.0.0.0 (192.168.161.245)
Origin IGP, metric 0, weight 32768, valid, sourced, local, bestpath-from-AS Local, best (First path received)
Last update: Wed Sep 16 15:03:03 2020
eva(config-router-af)# redistribute connected
eva(config-router-af)# do show bgp ipv4 uni 192.168.161.0
BGP routing table entry for 192.168.161.0/24
Paths: (2 available, best #2, table default)
Not advertised to any peer
Local
0.0.0.0(eva) from 0.0.0.0 (192.168.161.245)
Origin incomplete, metric 0, weight 32768, valid, sourced
Last update: Wed Sep 16 15:03:32 2020
Local
0.0.0.0(eva) from 0.0.0.0 (192.168.161.245)
Origin IGP, metric 0, weight 32768, valid, sourced, local, bestpath-from-AS Local, best (Origin)
Last update: Wed Sep 16 15:03:03 2020
eva(config-router-af)#
Notice the route choosen depends on order received
Fixed behavior:
eva# conf
eva(config)# router bgp 323
eva(config-router)# address-family ipv4 uni
eva(config-router-af)# redistribute connected
eva(config-router-af)# network 192.168.161.0/24
eva(config-router-af)# do show bgp ipv4 uni 192.168.161.0
BGP routing table entry for 192.168.161.0/24
Paths: (2 available, best #1, table default)
Not advertised to any peer
Local
0.0.0.0(eva) from 0.0.0.0 (192.168.161.245)
Origin IGP, metric 0, weight 32768, valid, sourced, local, bestpath-from-AS Local, best (Origin)
Last update: Wed Sep 16 15:03:03 2020
Local
0.0.0.0(eva) from 0.0.0.0 (192.168.161.245)
Origin incomplete, metric 0, weight 32768, valid, sourced
Last update: Wed Sep 16 15:02:52 2020
eva(config-router-af)# no redistribute connected
eva(config-router-af)# do show bgp ipv4 uni 192.168.161.0
BGP routing table entry for 192.168.161.0/24
Paths: (1 available, best #1, table default)
Not advertised to any peer
Local
0.0.0.0(eva) from 0.0.0.0 (192.168.161.245)
Origin IGP, metric 0, weight 32768, valid, sourced, local, bestpath-from-AS Local, best (First path received)
Last update: Wed Sep 16 15:03:03 2020
eva(config-router-af)# redistribute connected
eva(config-router-af)# do show bgp ipv4 uni 192.168.161.0
BGP routing table entry for 192.168.161.0/24
Paths: (2 available, best #2, table default)
Not advertised to any peer
Local
0.0.0.0(eva) from 0.0.0.0 (192.168.161.245)
Origin incomplete, metric 0, weight 32768, valid, sourced
Last update: Wed Sep 16 15:03:32 2020
Local
0.0.0.0(eva) from 0.0.0.0 (192.168.161.245)
Origin IGP, metric 0, weight 32768, valid, sourced, local, bestpath-from-AS Local, best (Origin)
Last update: Wed Sep 16 15:03:03 2020
eva(config-router-af)#
Ticket: CM-31490
Found-by: Trey Aspelund <taspelund@nvidia.com>
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add code to handle MED matching:
- When MED matches act as normal.
- When MED doesn't match do the following:
* Uninstall the aggregate route
* Unsuppress routes (if using summary-only)
- When MED didn't match, but now matches:
* Install the aggregate route
* Suppress all routes (if using summary-only)
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
If you are including a network statement of a /32
then the current bgp martian checks will match the /32
together.
Problem:
!
router bgp 3235
neighbor 192.168.161.2 remote-as external
neighbor 192.168.161.131 remote-as external
!
address-family ipv4 unicast
network 10.10.3.11/32
network 192.168.161.0/24
no neighbor 192.168.161.2 activate
neighbor 192.168.161.2 route-map BLUE in
exit-address-family
!
eva# show bgp ipv4 uni
BGP table version is 1, local router ID is 10.10.3.11, vrf id 0
Default local pref 100, local AS 3235
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
10.10.3.11/32 0.0.0.0(eva) 0 32768 i
*> 192.168.161.0/24 0.0.0.0(eva) 0 32768 i
Displayed 2 routes and 2 total paths
eva# show bgp import-check-table
Current BGP import check cache:
192.168.161.0 valid [IGP metric 0], #paths 1
if enp39s0
Last update: Fri Sep 25 08:00:42 2020
10.10.3.11 valid [IGP metric 0], #paths 1
if lo
Last update: Fri Sep 25 08:00:42 2020
eva# show bgp ipv4 uni summ
BGP router identifier 10.10.3.11, local AS number 3235 vrf-id 0
BGP table version 1
RIB entries 3, using 576 bytes of memory
Peers 1, using 21 KiB of memory
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd PfxSnt
janelle(192.168.161.131) 4 60000 69 70 0 0 0 00:03:21 0 1
Total number of neighbors 1
When we are deciding that a nexthop is valid there is not much point in checking
that a static route has a martian nexthop or not, since we self derived it already.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
bgp_attr_intern(attr) takes an attribute, duplicates it, and inserts it
into the attribute hash table, returning the inserted attr. This is done
when processing a bgp update. We store the returned attribute in the
path info struct. However, later on we modify one of the fields of the
attribute. This field is inspected by attrhash_cmp, the function that
allows the hash table to select the correct item from the hash chain for
a given key when doing a lookup on an item. By modifying the field after
it's been inserted, we open the possibility that two items in the same
chain that at insertion time were differential by attrhash_cmp becomes
equal according to that function. When performing subsequent hash
lookups, it is then indeterminate which of the equivalent items the hash
table will select from the chain (in practice it is the first one but
this may not be the one we want). Thus, it is illegal to modify
data used by a hash comparison function after inserting that data into
a hash table.
In fact this is occurring for attributes. We insert two attributes that
hash to the same key and thus end up in the same hash chain. Then we
modify one of them such that the two items now compare equal. Later one
we want to release the second item from the chain before XFREE()'ing it,
but since the two items compare equal we get the first item back, then
free the second one, which constitutes two bugs, the first being the
wrong attribute removed from the hash table and the second being a
dangling pointer stored in the hash table.
To rectify this we need to perform any modifications to an attr before
it is inserted into the table, i.e., before calling bgp_attr_intern().
This patch does that by moving the sole modification to the attr that
occurs after the insert (that I have seen) before that call.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
This will check route-maps as well, not only prefix-lists, access-lists, and
filter-lists.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
until now, the assumption was done in bgp flowspec code that the
information contained was an ipv4 flowspec prefix. now that it is
possible to handle ipv4 or ipv6 flowspec prefixes, that information is
stored in prefix_flowspec attribute. Also, some unlocking is done in
order to process ipv4 and ipv6 flowspec entries.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When a SYNC route i.e. a route with a local ES as destination is
rxed on a switch (say L11) from an ES peer (say L12) a local
MAC/neigh entry is created on L11 with the local access port
as dest port.
Creation of the local entry triggers a local path advertisement from
L11. This could be a "locally-active" path or a "locally-inactive"
path. Inactive paths are advertised with the proxy bit.
To ensure that the local entry is not deleted by a SYNC route it is
given absolute precedence over peer-paths.
If there are two non-local paths with the same dest ES and same MM
seq number the non-proxy path is preferred. This is done to ensure
that we don't lose track of the peer-activity.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
1. Sample ES display
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
torm-11# sh bgp l2vpn evpn es
ES Flags: L local, R remote, I inconsistent
VTEP Flags: E ESR/Type-4, A active nexthop
ESI Flags RD #VNIs VTEPs
03:00:00:00:00:01:11:00:00:01 LR 27.0.0.15:15 10 27.0.0.16(EA)
03:00:00:00:00:01:22:00:00:02 LR 27.0.0.15:16 10 27.0.0.16(EA)
03:00:00:00:00:01:22:00:00:03 LR 27.0.0.15:17 10 27.0.0.16(EA)
03:00:00:00:00:02:11:00:00:01 R - 10 27.0.0.17(A),27.0.0.18(A)
03:00:00:00:00:02:22:00:00:02 R - 10 27.0.0.17(A),27.0.0.18(A)
03:00:00:00:00:02:22:00:00:03 R - 10 27.0.0.17(A),27.0.0.18(A)
torm-11#
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
2. Sample ES-EVI display
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
torm-11# sh bgp l2vpn evpn es-evi
Flags: L local, R remote, I inconsistent
VTEP-Flags: E EAD-per-ES, V EAD-per-EVI
VNI ESI Flags VTEPs
1005 03:00:00:00:00:01:11:00:00:01 LR 27.0.0.16(EV)
1005 03:00:00:00:00:01:22:00:00:02 LR 27.0.0.16(EV)
1005 03:00:00:00:00:01:22:00:00:03 LR 27.0.0.16(EV)
1005 03:00:00:00:00:02:11:00:00:01 R 27.0.0.17(EV),27.0.0.18(EV)
1005 03:00:00:00:00:02:22:00:00:02 R 27.0.0.17(EV),27.0.0.18(EV)
1005 03:00:00:00:00:02:22:00:00:03 R 27.0.0.17(EV),27.0.0.18(EV)
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
3. Sample EAD route display
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
torm-11# sh bgp l2vpn evpn route type ead
BGP table version is 19, local router ID is 27.0.0.15
Status codes: s suppressed, d damped, h history, * valid, > best, i - internal
Origin codes: i - IGP, e - EGP, ? - incomplete
EVPN type-1 prefix: [4]:[ESI]:[EthTag]:[IPlen]:[VTEP-IP]
EVPN type-2 prefix: [2]:[EthTag]:[MAClen]:[MAC]:[IPlen]:[IP]
EVPN type-3 prefix: [3]:[EthTag]:[IPlen]:[OrigIP]
EVPN type-4 prefix: [4]:[ESI]:[IPlen]:[OrigIP]
EVPN type-5 prefix: [5]:[EthTag]:[IPlen]:[IP]
Network Next Hop Metric LocPrf Weight Path
Extended Community
Route Distinguisher: 27.0.0.15:5
*> [1]:[0]:[03:00:00:00:00:01:11:00:00:01]:[128]:[0.0.0.0]
27.0.0.15 32768 i
ET:8 RT:5550:1009
*> [1]:[0]:[03:00:00:00:00:01:22:00:00:02]:[128]:[0.0.0.0]
27.0.0.15 32768 i
ET:8 RT:5550:1009
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Add ESI as an inline attribute field along with the other EVPN
attributes. This may be re-worked when the rest of the EVPN
attributes find a new home.
Some cleanup has been done to get rid of stale/unused references
to ESI. And also to consolidate duplicate definitions of ES ID
types.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
When we have a prefix that has been selected, note that that
particular flag has been set and give that information to the
end user.
eva# show bgp ipv4 uni neighbors 192.168.161.131 prefix-counts
Prefix counts for 192.168.161.131, IPv4 Unicast
PfxCt: 814246
Counts from RIB table walk:
Adj-in: 0
Damped: 0
Removed: 0
History: 0
Stale: 0
Valid: 814246
All RIB: 814246
PfxCt counted: 814246
PfxCt Best Selected: 0
Useable: 814246
eva# show bgp ipv4 uni neighbors 192.168.161.2 prefix-counts
Prefix counts for 192.168.161.2, IPv4 Unicast
PfxCt: 814070
Counts from RIB table walk:
Adj-in: 0
Damped: 0
Removed: 0
History: 0
Stale: 0
Valid: 814070
All RIB: 814070
PfxCt counted: 814070
PfxCt Best Selected: 814070
Useable: 814070
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If _force_ is set, then ALL prefixes are counted for maximum instead of
accepted only. This is useful for cases where an inbound filter is applied,
but you want maximum-prefix to act on ALL (including filtered) prefixes.
For instance, we have a configuration like:
neighbor r1 maximum-prefix 10
neighbor r1 prefix-list custom in
!
ip prefix-list custom seq 1 permit 10.0.0.0/24
ip prefix-list custom seq 2 permit 10.0.1.0/24
This will accept only 2 prefixes and discard all others instead of
shutting down the session when 10 is reached.
With this new knob (force), we will count all received prefixes and shutdown
the session when 10 is reached.
The bigger problem is when you have lots of peers with full feed and such a
configuration like in an example.
This is kinda re-ordering of how to treat filter vs. maximum-prefix.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
```
(gdb) bt
0 0x00007f45a6f0a781 in raise () from /lib/x86_64-linux-gnu/libc.so.6
1 0x00007f45a6ef455b in abort () from /lib/x86_64-linux-gnu/libc.so.6
2 0x00007f45a7781920 in core_handler (signo=11, siginfo=0x7fffac7b84b0, context=<optimized out>) at lib/sigevent.c:228
3 <signal handler called>
4 0x000055a4133c0f32 in bgp_table_stats (vty=vty@entry=0x55a415acb240, bgp=0x0, afi=AFI_IP, safi=SAFI_UNICAST, json_array=json_array@entry=0x0) at bgpd/bgp_route.c:11412
5 0x000055a4133c13fb in show_ip_bgp_afi_safi_statistics (self=<optimized out>, vty=0x55a415acb240, argc=6, argv=<optimized out>) at bgpd/bgp_route.c:10749
6 0x00007f45a773917d in cmd_execute_command_real (vline=vline@entry=0x55a415ab7e10, vty=vty@entry=0x55a415acb240, cmd=cmd@entry=0x0, filter=FILTER_RELAXED)
at lib/command.c:909
7 0x00007f45a773afdf in cmd_execute_command (vline=vline@entry=0x55a415ab7e10, vty=vty@entry=0x55a415acb240, cmd=0x0, vtysh=vtysh@entry=0) at lib/command.c:968
8 0x00007f45a773b135 in cmd_execute (vty=vty@entry=0x55a415acb240, cmd=cmd@entry=0x55a415ace950 "show ip bgp vrf all statistics", matched=matched@entry=0x0,
vtysh=vtysh@entry=0) at lib/command.c:1122
9 0x00007f45a7794d62 in vty_command (vty=vty@entry=0x55a415acb240, buf=0x55a415ace950 "show ip bgp vrf all statistics") at lib/vty.c:526
10 0x00007f45a7794fb6 in vty_execute (vty=vty@entry=0x55a415acb240) at lib/vty.c:1293
11 0x00007f45a7797804 in vtysh_read (thread=<optimized out>) at lib/vty.c:2126
12 0x00007f45a778f641 in thread_call (thread=thread@entry=0x7fffac7bb040) at lib/thread.c:1550
13 0x00007f45a775b6d8 in frr_run (master=0x55a415542820) at lib/libfrr.c:1098
14 0x000055a4133815d6 in main (argc=10, argv=0x7fffac7bb2a8) at bgpd/bgp_main.c:509
```
"show ip bgp vrf all statistics" should show statistics for all VRFs if "all"
is specified.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Remove mid-string line breaks, cf. workflow doc:
.. [#tool_style_conflicts] For example, lines over 80 characters are allowed
for text strings to make it possible to search the code for them: please
see `Linux kernel style (breaking long lines and strings)
<https://www.kernel.org/doc/html/v4.10/process/coding-style.html#breaking-long-lines-and-strings>`_
and `Issue #1794 <https://github.com/FRRouting/frr/issues/1794>`_.
Scripted commit, idempotent to running:
```
python3 tools/stringmangle.py --unwrap `git ls-files | egrep '\.[ch]$'`
```
Signed-off-by: David Lamparter <equinox@diac24.net>
It's hard to cope with cases when next-hop is changed/unchanged or
peers are non-direct.
It would be better to show the hostname and nexthop IP address (both)
under `show bgp` to quickly identify the source and the real next-hop
of the route.
If `bgp default show-nexthop-hostname` is toggled the output looks like:
```
spine1-debian-9# show bgp
BGP table version is 1, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 65002
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
* 2a02:4780::/64 fe80::a00:27ff:fe09:f8a3(exit1-debian-9)
0 0 65001 ?
spine1-debian-9# show ip bgp
BGP table version is 5, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 65002
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 10.255.255.0/24 192.168.0.1(exit1-debian-9)
0 0 65001 ?
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
If the RT changes on a L3VPN route then any leak of this route into
a VRF should be withdrawn.
Extend existing EVPN check for RT change to cover L3VPN routes.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
This is the bulk part extracted from "bgpd: Convert from `struct
bgp_node` to `struct bgp_dest`". It should not result in any functional
change.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
If we have something like:
```
ip route 1.1.1.0/24 Null0
!
router bgp 100
no bgp ebgp-requires-policy
neighbor 192.168.0.2 remote-as 200
!
address-family ipv4 unicast
network 1.1.1.0/24
redistribute connected
exit-address-family
!
line vty
!
```
1.1.1.0/24 is not advertised due to martian nexthop (0.0.0.0). It starts
working only when we use `redistribute static`.
By checking if it's a BGP static route we able to announce
1.1.1.0/24 with `network 1.1.1.0/24` without redistribute even when
`bgp import-check` is enabled.
Disabling `bgp import-check` works as well, but it's enabled by default
since 7.4.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Non-best paths (path info structures) also need to be freed during
table cleanup not only to release their memory but to also ensure
any linkages are updated correctly. One such example is for EVPN
where there is a link between the imported path info (in a L2 or
L3 vrf instance) and its parent path info.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Without specifying a default afi/safi we get a segfault:
```
(gdb) frame 4
bgp_table_stats (..., afi=32724, safi=SAFI_UNICAST, ...
11349 if (!bgp->rib[afi][safi]) {
(gdb)
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
unicast and labeled-unicast share the same table, but configuration should
be visible for both independently. Without this fix it confuses a bit
because when you enter `network 10.0.0.0/24` under labeled-unicast it's
written in unicast family block.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Replace sprintf with snprintf where straightforward to do so.
- sprintf's into local scope buffers of known size are replaced with the
equivalent snprintf call
- snprintf's into local scope buffers of known size that use the buffer
size expression now use sizeof(buffer)
- sprintf(buf + strlen(buf), ...) replaced with snprintf() into temp
buffer followed by strlcat
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
When we receive an UPDATE with MP_NEXTHOP len as 32 bytes, we shouldn't
check if the global (1st) nexthop is unspecified.
Peering between bird and FRRouting we receive from Bird something like:
```
rcvd UPDATE w/ attr: , origin i, mp_nexthop ::(fe80::a00:27ff:fe09:f8a3)
```
The link-local (2nd) nexthop is valid and validated later in the code.
Before it was marked:
```
IPv6 unicast -- DENIED due to: martian or self next-hop;
```
After it's a valid prefix:
```
spine1-debian-9# show bgp
BGP table version is 0, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 65002
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
2a02:4780::/64 fe80::a00:27ff:fe09:f8a3
0 65001 i
Displayed 1 routes and 1 total paths
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
In real world sometimes happens that bgp_nexthop_cache is NULL. Avoid
segfaulting when using `show [ip] bgp ...` CLI commands.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
The problem is when using kinda such topologies:
(192.168.1.1/32) r1 <-- eBGP --> r2 <-- iBGP --> r3
Looking at r3's nexthop for 192.168.1.1/32 we have it as r2, but really
it MUST be r1.
Checking if the nexthop is connected solves the problem even for cases
when route-reflectors are used.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Some competitive vendors like Cisco, Bird, OpenBGPD,
Nokia already have this by default enabled.
The list is here: https://github.com/bgp/RFC8212
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Problem Description:
=====================
+--+ +--+
|R1|-(192.201.202.1)----iBGP----(192.201.202.2)-|R2|
+--+ +--+
Routes on R2:
=============
S>* 202.202.202.202/32 [1/0] via 192.201.78.1, ens256, 00:40:48
Where, the next-hop network, 192.201.78.0/24, is a directly connected network address.
C>* 192.201.78.0/24 is directly connected, ens256, 00:40:48
Configurations on R1:
=====================
!
router bgp 201
bgp router-id 192.168.0.1
neighbor 192.201.202.2 remote-as 201
!
Configurations on R2:
=====================
!
ip route 202.202.202.202/32 192.201.78.1
!
router bgp 201
bgp router-id 192.168.0.2
neighbor 192.201.202.1 remote-as 201
!
address-family ipv4 unicast
redistribute static
exit-address-family
!
Step-1:
=======
R1 receives the route 202.202.202.202/32 from R2.
R1 installs the route in its BGP RIB.
Step-2:
=======
On R1, a connected interface address is added.
The address is the same as the next-hop of the BGP route received from R2 (192.201.78.1).
Point of Failure:
=================
R1 resolves the BGP route even though the route's next-hop is its own connected address.
Even though this appears to be a misconfiguration it would still be better to safeguard the code against it.
Fix:
====
When BGP receives a connected route from Zebra, it processes the
routes for the next-hop update.
While doing so, BGP must ignore routes whose next-hop address matches
the address of the connected route for which Zebra sent the next-hop update
message.
Signed-off-by: NaveenThanikachalam <nthanikachal@vmware.com>
Ensure that upon a link-bandwidth change - for e.g., due to change in
the number of multipaths - EVPN type-5 route injection is triggered.
In the absence of this, the proper link-bandwidth is not updated in
EVPN type-5 routes originated by the router.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
take into account polychaeta tips ono code style.
also, take into account miscellaneous code style recommandations like
braces usage.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This macro is undefined if vnc is disabled, and while it defaults to 0,
this is still wrong and causes issues with -Werror
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
- each statistics is encapsulated into concatenated "<afi><safi>" value.
- the json encoding for floating and double values is using json api
double api. this change is done for bgp statistics.
- the lines over 80 characters have been handled.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
this command is a shortcut to facilitate the extraction of statistics
for all afi/safi related to one bgp instance.
the command is: show bgp [vrf XX] statistics-all [json]
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
safis that use a route distinguisher in bgp tables, and as such
introduce a two level hierarchy on the bgp table, must be made available
to statistics too.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
add json support for show bgp statistics command.
The title of the stats entry is aggregated without spaces.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Support configurable options to control how link bandwidth is handled
by the receiver. The default behavior is to automatically honor the
link bandwidths received and use it to perform a weighted ECMP BUT only
if all paths in the multipath have associated link bandwidth; if one or
more paths do not have link bandwidth, normal ECMP is performed among
the multipaths. This behavior is as recommended by
https://tools.ietf.org/html/draft-ietf-idr-link-bandwidth.
The additional options available are to (a) completely ignore any link
bandwidth (i.e., weighted ECMP is effectively disabled), (b) skip paths
in the multipath which do not have link bandwidth and perform weighted
ECMP among the other paths (if at least some paths have the bandwidth)
or (c) use a default weight (value chosen is 1) for the paths which
do not have link bandwidth.
The command syntax is
bgp bestpath bandwidth <ignore|skip-missing|default-weight-for-missing>
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
When announcing ourselves as the next hop (e.g., to EBGP peers), if the
best path has the link bandwidth extended community and it is transitive,
change the value of the link bandwidth to the cumulative downstream
bandwidth (sum of the link bandwidths of all our multipaths) as this
makes the most sense. It is also implied by
https://tools.ietf.org/html/draft-mohanty-bess-ebgp-dmz. Of course, do
not override the link bandwidth if it has been specified by policy.
Note: Transitive extended communities will be automatically passed along
to EBGP peers; this commit is updating the value that is announced to
something that is the most appropriate.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Implement the code to handle the other route-map options to generate
the link bandwidth, namely, to use the cumulative bandwidth or to
base this on the number of multipaths. In the latter case, a reference
bandwidth is internally chosen - the implementation uses a value of
1 Gbps.
These additional options mean that the prefix may need to be advertised
if there is a link bandwidth change, which is a new criteria. Define a
new path (change) flag to support this and implement the advertisement.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Add new function `bgp_node_get_prefix()` and modify
the bgp code base to use it.
This is prep work for the struct bgp_dest rework.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Show if this malformed under `show [ip] bgp <prefix>`:
```
eva# sh ip bgp 103.79.124.0/22
BGP routing table entry for 103.79.124.0/22
Paths: (1 available, best #1, table default)
Advertised to non peer-group peers:
192.168.201.136
64539 15096 6939 7545 7545 136001, (aggregated by 0(malformed) 0.0.0.0)
192.168.201.136 from 192.168.201.136 (192.168.201.136)
Origin IGP, valid, external, best (First path received)
Last update: Thu Mar 26 10:02:07 2020
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Line break at the end of the message is implicit for zlog_* and flog_*,
don't put it in the string. Mid-message line breaks are currently
unsupported. (LF is "end of message" in syslog.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Modify code to use lookup function agg_node_get_prefix()
as the abstraction layer. When we rework bgp_node to
bgp_dest this will allow us to greatly limit the amount
of work needed to do that.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Future work needs the ability to specify a
const struct prefix value. Iterate into
bgp a bit to get this started.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Defer the grabbing of the prefix for as long as is possible.
This is a long term rework of how we access the `struct bgp_node`
to only use accessor functions.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Modify more code to use `const struct prefix` throughout
bgp. This is all prep work for adding an accessor function
for bgp_node to get the prefix and reduce all the places that
code needs to be touched when we get that work done.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Some were converted to bool, where true/false status is needed.
Converted to void only those, where the return status was only false or true.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Ensure that the EVPN advertise route-map is applied on a copy of the
original path_info and associated attribute, so that if the route-map
has SET clauses, they can operate properly. This closely follows
the model already in use in other route-map application code.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
A BGP update-group is dynamically created to group together a set of peers
such that any BGP updates can be formed just once for the entire group and
only the next hop attribute may need to be modified when the update is sent
out to each peer in the group. The update formation code attempts to
determine as much as possible if the next hop will be set to our own IP
address for every peer in the group. This helps to avoid additional checks
at the point of sending the update (which happens on a per-peer basis) and
also because some other attributes may/could vary depending on whether the
next hop is set to our own IP or not. Resetting the next hop to our own IP
address is the most common behavior for EBGP peerings in the absence of
other user-configured or internal (e.g., for l2vpn/evpn) settings and
peerings on a shared subnet.
The code had a flaw in the multiaccess check to see if there are peers in
the update group which are on a shared subnet as the next hop of the path
being announced - the source peer could itself be in the same update group
and cause the check to give an incorrect result. Modify the check to skip
the source peer so that the check is more accurate.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
The bgp reason code was being reset in bgp_best_selection
by rerunning bgp_path_info_cmp multiple times under certain
receiving patterns of data from peers.
This is the debugs that show this issue:
2020/03/16 19:17:22.523780 BGP: 2001:20:1:1::6 rcvd UPDATE w/ attr: nexthop 20.1.1.6, origin i, metric 600, community 1000:1006, path 20
2020/03/16 19:17:22.523819 BGP: 2001:20:1:1::6 rcvd 20.10.0.6/32 IPv4 unicast
2020/03/16 19:17:22.556168 BGP: 20.1.1.6 rcvd UPDATE w/ attr: nexthop 20.1.1.6, origin i, metric 500, community 1000:1006, path 20
2020/03/16 19:17:22.556209 BGP: 20.1.1.6 rcvd 20.10.0.6/32 IPv4 unicast
2020/03/16 19:17:22.572358 BGP: bgp_process_main_one: p=20.10.0.6/32 afi=IPv4, safi=unicast start
2020/03/16 19:17:22.572408 BGP: 20.10.0.6/32: Comparing path 2001:20:1:1::6 flags 0x410 with path 20.1.1.6 flags 0x410
2020/03/16 19:17:22.572415 BGP: 20.10.0.6/32: path 2001:20:1:1::6 loses to path 20.1.1.6 due to MED 600 > 500
2020/03/16 19:17:22.572422 BGP: 20.10.0.6/32: path 20.1.1.6 is the bestpath from AS 20
2020/03/16 19:17:22.572429 BGP: 20.10.0.6/32: path 20.1.1.6 is the initial bestpath
2020/03/16 19:17:22.572435 BGP: bgp_best_selection: pi 0x5627187c66c0 dmed
2020/03/16 19:17:22.572441 BGP: 20.10.0.6/32: After path selection, newbest is path 20.1.1.6 oldbest was NONE
2020/03/16 19:17:22.572447 BGP: 20.10.0.6/32: path 20.1.1.6 is the bestpath, add to the multipath list
2020/03/16 19:17:22.572453 BGP: 20.10.0.6/32: path 2001:20:1:1::6 has the same nexthop as the bestpath, skip it
2020/03/16 19:17:22.572460 BGP: 20.10.0.6/32: starting mpath update, newbest 20.1.1.6 num candidates 1 old-mpath-count 0 old-cum-bw u0
2020/03/16 19:17:22.572466 BGP: 20.10.0.6/32: comparing candidate 20.1.1.6 with existing mpath NONE
2020/03/16 19:17:22.572473 BGP: 20.10.0.6/32: New mpath count (incl newbest) 1 mpath-change NO all_paths_lb 0 cum_bw u0
Effectively if BGP receives 2 paths it could end up running bgp_path_info_cmp multiple times
and in some situations overwrite the reason selected the first time through.
In this example path selection is run and the MED is the reason for the choice.
Then in bgp_best_selection is run again this time clearing new_select
to NULL before calling path selection for the first time. This second
call into path selection resets the reason, since it is only passing in one
path. So save the last reason selected and restore in this case.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Override ORIGIN attribute if defined.
E.g.: Cisco and Juniper set ORIGIN for aggregated address
to IGP which is not what rfc4271 says.
This enables the same behavior, optionally.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
The act of peer_sort() being called always set this value
even when we are just looking it up. We need to seperate
out the idea of lookup from set.
For those places that this is immediately obvious that
this is a lookup switch over to using this function.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
