Implemented as per the feature description given in the source link.
Descriprion:
The BGP conditional advertisement feature uses the non-exist-map or exist-map
and the advertise-map keywords of the neighbor advertise-map command in order
to track routes by the route prefix.
non-exist-map :
If a route prefix is not present in output of the non-exist-map command, then
the route specified by the advertise-map command is announced.
exist-map :
If a route prefix is present in output of the exist-map command, then the route
specified by the advertise-map command is announced.
The conditional BGP announcements are sent in addition to the normal
announcements that a BGP router sends to its peers.
The conditional advertisement process is triggered by the BGP scanner process,
which runs every 60 seconds. This means that the maximum time for the conditional
advertisement to take effect is 60 seconds. The conditional advertisement can take
effect sooner, depending on when the tracked route is removed from the BGP table
and when the next instance of the BGP scanner occurs.
Sample Configuration on DUT
---------------------------
Router2# show running-config
Building configuration...
Current configuration:
!
frr version 7.6-dev-MyOwnFRRVersion
frr defaults traditional
hostname router
log file /var/log/frr/bgpd.log
log syslog informational
hostname Router2
service integrated-vtysh-config
!
debug bgp updates in
debug bgp updates out
!
debug route-map
!
ip route 200.200.0.0/16 blackhole
ipv6 route 2001:db8::200/128 blackhole
!
interface enp0s9
ip address 10.10.10.2/24
!
interface enp0s10
ip address 10.10.20.2/24
!
interface lo
ip address 2.2.2.2/24
ipv6 address 2001:db8::2/128
!
router bgp 2
bgp log-neighbor-changes
no bgp ebgp-requires-policy
neighbor 10.10.10.1 remote-as 1
neighbor 10.10.20.3 remote-as 3
!
address-family ipv4 unicast
network 2.2.2.0/24
network 200.200.0.0/16
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.10.1 advertise-map ADVERTISE non-exist-map CONDITION
neighbor 10.10.20.3 soft-reconfiguration inbound
exit-address-family
!
address-family ipv6 unicast
network 2001:db8::2/128
network 2001:db8::200/128
neighbor 10.10.10.1 activate
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.10.1 advertise-map ADVERTISE_6 non-exist-map CONDITION_6
neighbor 10.10.20.3 activate
neighbor 10.10.20.3 soft-reconfiguration inbound
exit-address-family
!
access-list CONDITION seq 5 permit 3.3.3.0/24
access-list ADVERTISE seq 5 permit 2.2.2.0/24
access-list ADVERTISE seq 6 permit 200.200.0.0/16
access-list ADVERTISE seq 7 permit 20.20.0.0/16
!
ipv6 access-list ADVERTISE_6 seq 5 permit 2001:db8::2/128
ipv6 access-list CONDITION_6 seq 5 permit 2001:db8::3/128
!
route-map ADVERTISE permit 10
match ip address ADVERTISE
!
route-map CONDITION permit 10
match ip address CONDITION
!
route-map ADVERTISE_6 permit 10
match ipv6 address ADVERTISE_6
!
route-map CONDITION_6 permit 10
match ipv6 address CONDITION_6
!
line vty
!
end
Router2#
Withdraw when non-exist-map prefixes present in BGP table:
----------------------------------------------------------
Router2# show ip bgp all wide
For address family: IPv4 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 10.10.10.1 0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 3.3.3.0/24 10.10.20.3 0 0 3 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Displayed 4 routes and 4 total paths
For address family: IPv6 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 fe80::a00:27ff:fecb:ad57 0 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::3/128 fe80::a00:27ff:fe76:6738 0 0 3 i
*> 2001:db8::200/128 :: 0 32768 i
Displayed 4 routes and 4 total paths
Router2#
Router2# show ip bgp neighbors 10.10.10.1
BGP neighbor is 10.10.10.1, remote AS 1, local AS 2, external link
!--- Output suppressed.
For address family: IPv4 Unicast
Update group 9, subgroup 5
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION, Advertise-map *ADVERTISE, status: Withdraw
1 accepted prefixes
For address family: IPv6 Unicast
Update group 10, subgroup 6
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION_6, Advertise-map *ADVERTISE_6, status: Withdraw
1 accepted prefixes
!--- Output suppressed.
Router2#
Here 2.2.2.0/24 & 200.200.0.0/16 (prefixes in advertise-map) are withdrawn
by conditional advertisement scanner as the prefix(3.3.3.0/24) specified
by non-exist-map is present in BGP table.
Router2# show ip bgp all neighbors 10.10.10.1 advertised-routes wide
For address family: IPv4 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 0.0.0.0 0 1 i
*> 3.3.3.0/24 0.0.0.0 0 3 i
Total number of prefixes 2
For address family: IPv6 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 :: 0 1 i
*> 2001:db8::3/128 :: 0 3 i
*> 2001:db8::200/128 :: 0 32768 i
Total number of prefixes 3
Router2#
Advertise when non-exist-map prefixes not present in BGP table:
---------------------------------------------------------------
After Removing 3.3.3.0/24 (prefix present in non-exist-map),
2.2.2.0/24 & 200.200.0.0/16 (prefixes present in advertise-map) are advertised
Router2# show ip bgp all wide
For address family: IPv4 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 10.10.10.1 0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Displayed 3 routes and 3 total paths
For address family: IPv6 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 fe80::a00:27ff:fecb:ad57 0 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::200/128 :: 0 32768 i
Displayed 3 routes and 3 total paths
Router2#
Router2# show ip bgp neighbors 10.10.10.1
!--- Output suppressed.
For address family: IPv4 Unicast
Update group 9, subgroup 5
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION, Advertise-map *ADVERTISE, status: Advertise
1 accepted prefixes
For address family: IPv6 Unicast
Update group 10, subgroup 6
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION_6, Advertise-map *ADVERTISE_6, status: Advertise
1 accepted prefixes
!--- Output suppressed.
Router2#
Router2# show ip bgp all neighbors 10.10.10.1 advertised-routes wide
For address family: IPv4 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 0.0.0.0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Total number of prefixes 3
For address family: IPv6 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 :: 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::200/128 :: 0 32768 i
Total number of prefixes 3
Router2#
Signed-off-by: Madhuri Kuruganti <k.madhuri@samsung.com>
If you advertise a default route (via default-originate) only if some
prefix is present in the BGP RIB (route-map specified) and this prefix
becomes unavailable, the default route keeps being advertised.
With this change, when we iterate over the BGP RIB to check if we can
advertise the default route, skip unavailable prefixes.
Signed-off-by: Alexander Chernavin <achernavin@netgate.com>
This is the bulk part extracted from "bgpd: Convert from `struct
bgp_node` to `struct bgp_dest`". It should not result in any functional
change.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Issue:
Configuring default-originate when static default route is previously
advertised results in withdrawal of the route.
Fix :
Delete the adj-out entry for the previously advertised static
default route without sending explicit withdraw message.
Signed-off-by: kssoman <somanks@gmail.com>
Add new function `bgp_node_get_prefix()` and modify
the bgp code base to use it.
This is prep work for the struct bgp_dest rework.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When withdrawing addpaths, adj_lookup was called to find the path that
needed to be withdrawn. It would lookup in the RB tree based on subgroup
pointer alone, often find the path with the wrong addpath ID, and return
null. Only the path highest in the tree sent to the subgroup could be
found, thus withdrawn.
Adding the addpath ID to the sort criteria for the RB tree allows us to
simplify the logic for adj_lookup, and address this problem. We are able
to remove the logic around non-addpath subgroups because the addpath ID
is consistently 0 for non-addpath adj_outs, so special logic to skip
matching the addpath ID isn't required. (As a side note, addpath will
also never use ID 0, so there won't be any ambiguity when looking at the
structure content.)
Signed-off-by: Mitchell Skiba <mskiba@amazon.com>
With this change, we are able to set attributes via route-map to the default
route. It's useful in cases where we have two or more spines and we want to
prefer one router over others for leaves. This simplifies configuration instead
of using 'network 0.0.0.0/0' or 'ip route 0.0.0.0/0 ...' and 'redistribute
static' combination.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Include the coalesce time for the update group `show bgp update-group`
command as well as print out how long the coalesce timer waited
for on the timer pop.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Introducing a 3rd state for route_map_apply library function: RMAP_NOOP
Traditionally route map MATCH rule apis were designed to return
a binary response, consisting of either RMAP_MATCH or RMAP_NOMATCH.
(Route-map SET rule apis return RMAP_OKAY or RMAP_ERROR).
Depending on this response, the following statemachine decided the
course of action:
State1:
If match cmd returns RMAP_MATCH then, keep existing behaviour.
If routemap type is PERMIT, execute set cmds or call cmds if applicable,
otherwise PERMIT!
Else If routemap type is DENY, we DENYMATCH right away
State2:
If match cmd returns RMAP_NOMATCH, continue on to next route-map. If there
are no other rules or if all the rules return RMAP_NOMATCH, return DENYMATCH
We require a 3rd state because of the following situation:
The issue - what if, the rule api needs to abort or ignore a rule?:
"match evpn vni xx" route-map filter can be applied to incoming routes
regardless of whether the tunnel type is vxlan or mpls.
This rule should be N/A for mpls based evpn route, but applicable to only
vxlan based evpn route.
Also, this rule should be applicable for routes with VNI label only, and
not for routes without labels. For example, type 3 and type 4 EVPN routes
do not have labels, so, this match cmd should let them through.
Today, the filter produces either a match or nomatch response regardless of
whether it is mpls/vxlan, resulting in either permitting or denying the
route.. So an mpls evpn route may get filtered out incorrectly.
Eg: "route-map RM1 permit 10 ; match evpn vni 20" or
"route-map RM2 deny 20 ; match vni 20"
With the introduction of the 3rd state, we can abort this rule check safely.
How? The rules api can now return RMAP_NOOP to indicate
that it encountered an invalid check, and needs to abort just that rule,
but continue with other rules.
As a result we have a 3rd state:
State3:
If match cmd returned RMAP_NOOP
Then, proceed to other route-map, otherwise if there are no more
rules or if all the rules return RMAP_NOOP, then, return RMAP_PERMITMATCH.
Signed-off-by: Lakshman Krishnamoorthy <lkrishnamoor@vmware.com>
Introducing a 3rd state for route_map_apply library function: RMAP_NOOP
Traditionally route map MATCH rule apis were designed to return
a binary response, consisting of either RMAP_MATCH or RMAP_NOMATCH.
(Route-map SET rule apis return RMAP_OKAY or RMAP_ERROR).
Depending on this response, the following statemachine decided the
course of action:
Action: Apply route-map match and return the result (RMAP_MATCH/RMAP_NOMATCH)
State1: Receveived RMAP_MATCH
THEN: If Routemap type is PERMIT, execute other rules if applicable,
otherwise we PERMIT!
Else: If Routemap type is DENY, we DENYMATCH right away
State2: Received RMAP_NOMATCH, continue on to next route-map, otherwise,
return DENYMATCH by default if nothing matched.
With reference to PR 4078 (https://github.com/FRRouting/frr/pull/4078),
we require a 3rd state because of the following situation:
The issue - what if, the rule api needs to abort or ignore a rule?:
"match evpn vni xx" route-map filter can be applied to incoming routes
regardless of whether the tunnel type is vxlan or mpls.
This rule should be N/A for mpls based evpn route, but applicable to only
vxlan based evpn route.
Today, the filter produces either a match or nomatch response regardless of
whether it is mpls/vxlan, resulting in either permitting or denying the
route.. So an mpls evpn route may get filtered out incorrectly.
Eg: "route-map RM1 permit 10 ; match evpn vni 20" or
"route-map RM2 deny 20 ; match vni 20"
With the introduction of the 3rd state, we can abort this rule check safely.
How? The rules api can now return RMAP_NOOP (or another enum) to indicate
that it encountered an invalid check, and needs to abort just that rule,
but continue with other rules.
Question: Do we repurpose an existing enum RMAP_OKAY or RMAP_ERROR
as the 3rd state (or create a new enum like RMAP_NOOP)?
RMAP_OKAY and RMAP_ERROR are used to return the result of set cmd.
We chose to go with RMAP_NOOP (but open to ideas),
as a way to bypass the rmap filter
As a result we have a 3rd state:
State3: Received RMAP_NOOP
Then, proceed to other route-map, otherwise return RMAP_PERMITMATCH by default.
Signed-off-by:Lakshman Krishnamoorthy <lkrishnamoor@vmware.com>
The FIFO_* stuff in lib/fifo.h is no different from a simple unsorted
list. Just use DECLARE_LIST here so we can get rid of FIFO_*.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The adj_out data structure is a linked list of adjacencies
1 per update group. In a large scale env where we are
not using peer groups, this list lookup starts to become
rather costly. Convert to a better data structure for this.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The bgp_info data is stored as a void pointer in `struct bgp_node`.
Abstract retrieval of this data and setting of this data
into functions so that in the future we can move around
what is stored in bgp_node.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The motivation for this patch is to address a concerning behavior of
tx-addpath-bestpath-per-AS. Prior to this patch, all paths' TX ID was
pre-determined as the path was received from a peer. However, this meant
that any time the path selected as best from an AS changed, bgpd had no
choice but to withdraw the previous best path, and advertise the new
best-path under a new TX ID. This could cause significant network
disruption, especially for the subset of prefixes coming from only one
AS that were also communicated over a bestpath-per-AS session.
The patch's general approach is best illustrated by
txaddpath_update_ids. After a bestpath run (required for best-per-AS to
know what will and will not be sent as addpaths) ID numbers will be
stripped from paths that no longer need to be sent, and held in a pool.
Then, paths that will be sent as addpaths and do not already have ID
numbers will allocate new ID numbers, pulling first from that pool.
Finally, anything left in the pool will be returned to the allocator.
In order for this to work, ID numbers had to be split by strategy. The
tx-addpath-All strategy would keep every ID number "in use" constantly,
preventing IDs from being transferred to different paths. Rather than
create two variables for ID, this patch create a more generic array that
will easily enable more addpath strategies to be implemented. The
previously described ID manipulations will happen per addpath strategy,
and will only be run for strategies that are enabled on at least one
peer.
Finally, the ID numbers are allocated from an allocator that tracks per
AFI/SAFI/Addpath Strategy which IDs are in use. Though it would be very
improbable, there was the possibility with the free-running counter
approach for rollover to cause two paths on the same prefix to get
assigned the same TX ID. As remote as the possibility is, we prefer to
not leave it to chance.
This ID re-use method is not perfect. In some cases you could still get
withdraw-then-add behaviors where not strictly necessary. In the case of
bestpath-per-AS this requires one AS to advertise a prefix for the first
time, then a second AS withdraws that prefix, all within the space of an
already pending MRAI timer. In those situations a withdraw-then-add is
more forgivable, and fixing it would probably require a much more
significant effort, as IDs would need to be moved to ADVs instead of
paths.
Signed-off-by Mitchell Skiba <mskiba@amazon.com>
Do a straight conversion of `struct bgp_info` to `struct bgp_path_info`.
This commit will setup the rename of variables as well.
This is being done because `struct bgp_info` is not descriptive
of what this data actually is. It is path information for routes
that we keep to build the actual routes nexthops plus some extra
information.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The following types are nonstandard:
- u_char
- u_short
- u_int
- u_long
- u_int8_t
- u_int16_t
- u_int32_t
Replace them with the C99 standard types:
- uint8_t
- unsigned short
- unsigned int
- unsigned long
- uint8_t
- uint16_t
- uint32_t
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Removed in earlier version where the I/O pthread busy-waited for packets
to be posted to an output queue. Now that it's poll()-based, it's
necessary once again. Although this time we can say what we're actually
doing instead of a side effect of a write job.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Problem reported that a receiver of a default route issued across bgp
unnumbered peering using default originate would have the route stay
as inactive. Discovered we were messing up the nexthop value sent to
the peer in this one particular case. Manual testing good, fix supplied
to the submitter and verified to resolve the problem. bgp-smoke
completed successfully.
Ticket: CM-18634
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ignore the return value of some functions in the places we know they
can't fail, and other small fixes.
Regarding the change in bgpd/rfapi/rfapi_rib.c, asserting that
rfapiRaddr2Qprefix() didn't fail is the common idiom inside the rfapi
code.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This fixes the broken indentation of several foreach loops throughout
the code.
From clang's documentation[1]:
ForEachMacros: A vector of macros that should be interpreted as foreach
loops instead of as function calls.
[1] http://clang.llvm.org/docs/ClangFormatStyleOptions.html
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This reverts commit c14777c6bf.
clang 5 is not widely available enough for people to indent with. This
is particularly problematic when rebasing/adjusting branches.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Most of the attributes in 'struct attr_extra' allow for
the more interesting cases of using bgp. The extra
overhead of managing it will induce errors as we add
more attributes and the extra memory overhead is
negligible on anything but full bgp feeds.
Additionally this greatly simplifies the code for
the handling of data.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
bgpd: Fix missing label set
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
- All ipv4 labeled-unicast routes are now installed in the ipv4 unicast
table. This allows us to do things like take routes from an ipv4
unicast peer, allocate a label for them and TX them to a ipv4
labeled-unicast peer. We can do the opposite where we take routes from
a labeled-unicast peer, remove the label and advertise them to an ipv4
unicast peer.
- Multipath over a labeled route and non-labeled route is not allowed.
- You cannot activate a peer for both 'ipv4 unicast' and 'ipv4
labeled-unicast'
- The 'tag' variable was overloaded for zebra's route tag feature as
well as the mpls label. I added a 'mpls_label_t mpls' variable to
avoid this. This is much cleaner but resulted in touching a lot of
code.
The FSF's address changed, and we had a mixture of comment styles for
the GPL file header. (The style with * at the beginning won out with
580 to 141 in existing files.)
Note: I've intentionally left intact other "variations" of the copyright
header, e.g. whether it says "Zebra", "Quagga", "FRR", or nothing.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
The way thread.c is written, a caller who wishes to be able to cancel a
thread or avoid scheduling it twice must keep a reference to the thread.
Typically this is done with a long lived pointer whose value is checked
for null in order to know if the thread is currently scheduled. The
check-and-schedule idiom is so common that several wrapper macros in
thread.h existed solely to provide it.
This patch removes those macros and adds a new parameter to all
thread_add_* functions which is a pointer to the struct thread * to
store the result of a scheduling call. If the value passed is non-null,
the thread will only be scheduled if the value is null. This helps with
consistency.
A Coccinelle spatch has been used to transform code of the form:
if (t == NULL)
t = thread_add_* (...)
to the form
thread_add_* (..., &t)
The THREAD_ON macros have also been transformed to the underlying
thread.c calls.
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Implement support for negotiating IPv4 or IPv6 labeled-unicast address
family, exchanging prefixes and installing them in the routing table, as
well as interactions with Zebra for FEC registration. This is the
implementation of RFC 3107.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
To handle BGP NLRI EVPN messages, bgp is modified to handle AFI_L2VPN
and SAFI_EVPN values.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When clearing the adj-out for a subgroup (e.g., upon peer going down),
ensure that the adj-out is removed before unlocking the route node that
it points to, otherwise, there is a possibility that the route node may
be prematurely freed.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Ticket: CM-13690
Reviewed By: None
Testing Done: bgp-smoke, resilient-hash tests
(cherry picked from commit c3d7d35f3b7152c9e50e52c3cfd60b0dc52df703)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
* Solaris doesn't have u_int64_t, so use uint64_t instead. C99-style
fixed-width integers should always be preferred to improve portability;
* 's_addr' is a macro on Solaris, so we can't use it as a variable name.
Rename the 's_addr' variable to 'addr' in the
bgp_peer_conf_if_to_su_update_v4() function.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
lib/zebra.h has FILTER_X #define's. These do not belong there.
Put them in lib/filter.h where they belong.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
(cherry picked from commit 0490729cc033a3483fc6b0ed45085ee249cac779)
The nexthop setting for IPv6 default origination was incorrect, resulting in
the same (incorrect) IPv6 link-local nexthop being advertised to multiple
peers. The issue was also present for IPv4 default origination when IPv4
routes are advertised with IPv6 nextops (RFC 5549).
For default origination, we should just reset the nexthop when forming the
update for the update-group and let the outbound update/nexthop setting code
set it correctly.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-10623
Reviewed By: CCR-4677
Testing Done: Manual, bgp-min
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-8295
This is a regression from the addpath-tx commit. We loop over the adj_out list
but the adj can be freed within the body of the loop so we need to note adj->next
prior to the free.
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-8122
per draft-ietf-idr-ix-bgp-route-server-09:
2.3.2.2.2. BGP ADD-PATH Approach
The [I-D.ietf-idr-add-paths] Internet draft proposes a different
approach to multiple path propagation, by allowing a BGP speaker to
forward multiple paths for the same prefix on a single BGP session.
As [RFC4271] specifies that a BGP listener must implement an implicit
withdraw when it receives an UPDATE message for a prefix which
already exists in its Adj-RIB-In, this approach requires explicit
support for the feature both on the route server and on its clients.
If the ADD-PATH capability is negotiated bidirectionally between the
route server and a route server client, and the route server client
propagates multiple paths for the same prefix to the route server,
then this could potentially cause the propagation of inactive,
invalid or suboptimal paths to the route server, thereby causing loss
of reachability to other route server clients. For this reason, ADD-
PATH implementations on a route server should enforce send-only mode
with the route server clients, which would result in negotiating
receive-only mode from the client to the route server.
This allows us to delete all of the following code:
- All XXXX_rsclient() functions
- peer->rib
- BGP_TABLE_MAIN and BGP_TABLE_RSCLIENT
- RMAP_IMPORT and RMAP_EXPORT
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vivek Venkataraman <vivek@cumulusnetworks.com
Ticket: CM-8014
This implements addpath TX with the first feature to use it
being "neighbor x.x.x.x addpath-tx-all-paths".
One change to show output is 'show ip bgp x.x.x.x'. If no addpath-tx
features are configured for any peers then everything looks the same
as it is today in that "Advertised to" is at the top and refers to
which peers the bestpath was advertise to.
root@superm-redxp-05[quagga-stash5]# vtysh -c 'show ip bgp 1.1.1.1'
BGP routing table entry for 1.1.1.1/32
Paths: (6 available, best #6, table Default-IP-Routing-Table)
Advertised to non peer-group peers:
r1(10.0.0.1) r2(10.0.0.2) r3(10.0.0.3) r4(10.0.0.4) r5(10.0.0.5) r6(10.0.0.6) r8(10.0.0.8)
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r2(10.0.0.2) (10.0.0.2)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 8
Last update: Fri Oct 30 18:26:44 2015
[snip]
but once you enable an addpath feature we must display "Advertised to" on a path-by-path basis:
superm-redxp-05# show ip bgp 1.1.1.1/32
BGP routing table entry for 1.1.1.1/32
Paths: (6 available, best #6, table Default-IP-Routing-Table)
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r2(10.0.0.2) (10.0.0.2)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 8
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:44 2015
Local, (Received from a RR-client)
34.34.34.34 (metric 20) from r3(10.0.0.3) (10.0.0.3)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 7
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
56.56.56.56 (metric 20) from r6(10.0.0.6) (10.0.0.6)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 6
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
56.56.56.56 (metric 20) from r5(10.0.0.5) (10.0.0.5)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 5
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
34.34.34.34 (metric 20) from r4(10.0.0.4) (10.0.0.4)
Origin IGP, metric 0, localpref 100, valid, internal
AddPath ID: RX 0, TX 4
Advertised to: r8(10.0.0.8)
Last update: Fri Oct 30 18:26:39 2015
Local, (Received from a RR-client)
12.12.12.12 (metric 20) from r1(10.0.0.1) (10.0.0.1)
Origin IGP, metric 0, localpref 100, valid, internal, best
AddPath ID: RX 0, TX 3
Advertised to: r1(10.0.0.1) r2(10.0.0.2) r3(10.0.0.3) r4(10.0.0.4) r5(10.0.0.5) r6(10.0.0.6) r8(10.0.0.8)
Last update: Fri Oct 30 18:26:34 2015
superm-redxp-05#
Ticket: CM-7861
Reviewed by: CCR-3651
Testing: See bug
bgp is using both bm->master and master pointers interchangebly
for thread manipulation. Since they are the same thing consolidate
to one pointer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-6789
Reviewed By: CCR-3263
Testing Done: Manual Testing and smoke tests
Whenever some sort of output is encountered, added a json version with
proper logic as well.
This patch implements the 'update-groups' functionality in BGP. This is a
function that can significantly improve BGP performance for Update generation
and resultant network convergence. BGP Updates are formed for "groups" of
peers and then replicated and sent out to each peer rather than being formed
for each peer. Thus major BGP operations related to outbound policy
application, adj-out maintenance and actual Update packet formation
are optimized.
BGP update-groups dynamically groups peers together based on configuration
as well as run-time criteria. Thus, it is more flexible than update-formation
based on peer-groups, which relies on operator configuration.
[Note that peer-group based update formation has been introduced into BGP by
Cumulus but is currently intended only for specific releases.]
From 11098af65b2b8f9535484703e7f40330a71cbae4 Mon Sep 17 00:00:00 2001
Subject: [PATCH] updgrp commits
